Add basic sample rate conversion to the CXD56 Spresense audio
driver using libsamplerate. Currently conversion is only done
during playback and all output is fixed at 48 kHz.
Issues:
- 16 kHz SRC has glitches (unless data dump is enabled)
- 44.1 kHz SRC gets stuck
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
When audio fails it is usefull to have I2S transfer errors in place
to be able to track the issue
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
- Add new functions of GNSS
- Support the lower PWM frequency
- Add CONFIG_CPUFREQ_RELEASE_LOCK
- Add high speed ADC support
- Add HPADC input gain configuration
- Add eMMC device
- Frame buffer support
- Fix SD/GNSS/sensor drivers not worked
- Build errors
- Fix nxstyle issues
Because user may replace math library with other implementation
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Idb5f2a8b2a70302c8561553b3bcbc40529b5257f
In the previous implementation, cxd56_stop() checked the internal
state before sending AUDIO_MSG_STOP to the message queue. However,
if the worker thread took time to turn on AMP, cxd560_stop() was
not able to send the message and caused a deadlock.
This commit fixes this issue by always sending AUDIO_MSG_STOP
regardless of the internal state.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Add recording support to the Nuttx audio driver for Spresense.
- Supports 16 bit data with 48 kHz sample rate only for now.
- Supports 1 (dual mono) 2 or 4 channels.
- Only analog mics have been tested so digital is considered
unsupported.
Adds an initial Nuttx audio driver supporting the Spresense CXD56.
Being a work in progress the driver has a number of limitations:
- Audio playback only, no recording yet.
- Only 16 bit stereo playback is supported.
- In practice only 48kHz playback is supported due to missing SRC.
- Configure driver in "Device Drivers --> Audio Device Support".
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for those files under drivers/audio, drivers/net, and drivers/lcd.
This commit does two things:
1. First, it reorganizes the driver Kconfig files so that each is self contained. Before, a part of the driver configuration was in drivers/Kconfig and the rest was in in drivers/xyz/Konfig. Now, all of the driver configuration is consolitated in the latter.
2. Second, this commit correct numerous serious errors introduced in a previous reorganization of the driver Kconfig files. This was first noted by Nicholas Chin in PR270 for the case of the drivers/i2c/Kconfig but some examination indicates that the error was introduced into several other Kconfig files as well.
The nature of the introduced error was basically this:
- Nothing must intervene between the menuconfig selection and the following conditional configuration otpions.
- A previous PR erroneously introduced unconditional options between the menuconfig and the following confditional logic, thus corrupting the driver menus.
This error was easy to make because the driver Kconfig files were not well modularized. Making them fully self-contained should eliminate this kind of error in the future.
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
Squashed commit of the following:
net/netlink: Mark netlink support as EXPERIMENTAL.
net/netlink/netlink_sockif.c: Add netlink_getpeername to the socket interface.
net: Add getpeeername() support for netlink sockets.
include/netpacket/netlink.h: Add a few more definitions and structures used at the NetLink interface. Still missing many.
net/netlink: Add basic framework for Netlink socket support.
include/: Add basic Netlink definitions.
Change all Sony related copyright to conform with our company's internal rules.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
lc823450 smp improvement
* arch/arm/src/common: Apply irq_spin APIs to modifyregXX
Replace enter_critical_section with spin_lock_irqsave.
Replace leave_critical_section with spin_unlock_irqrestore.
Please see 6150299f54 as well.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Do not use modifyreg32() to enable Mutex.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Modify IRQ control for i2s
Interrupt will be handled on CPU0 with this change.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Apply irq_spin APIs to dma/syscontrol/usbdev.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/lc823450-xgevk: Assign CPU1 to lpwork
This change will improve load balancing for networking with RNDIS.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* drivers/audio/wm8776.c: Improve stability in SMP mode
Apply irq_spin APIs to improbe performance.
Repeat to process a message to avoid deadlock.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/lc823450-xgevk: Enable SPINLOCK_IRQ and NXPLAYER in rndis
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Change all calls to mq_receive() and mq_timedreceive() in the OS to calls to nxmq_receive() and nxmq_timedreceive(), making appropriate changes for differences in return values.
sched/mqueue: Add nxmq_receive() and mxmq_timedreceive() which are functionally equivalent to the standard mq_receive and mq_timedreceive() except that (1) they do not create cancellation points, and (2) the do not modify the application's errno variable.
Change all calls to mq_send() and mq_timedsend() in the OS to calls to nxmq_send() and nxmq_timedsend(), making appropriate changes for differences in return values.
sched/mqueue: Add internal function nxmq_send() and nxmq_timedsend() that are equivalent to mq_send() and mq_timedsend() except that they do not create cancellation points and do to not modify the errno variable.
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
