stm32: Align ethernet config name to netnsh
nsh-ethernet was only used for stm32f7*-disco,
other configurations with network enabled are commonly
named netnsh or derived: (eg: nucleo-144/f7670-netnsh)
Change-Id: I80a33c8e22fbc7ccc9caf6b483478ae2c3a075ad
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
nucleo-144-f767-netnsh: Add ethernet config
* nucleo-f767zi: Use on board USB UART as default console
Board is powered by USB which can be used as UART link for upload and console
Previously it was set to use Arduino shield which developer may not have,
Change-Id: If3c1e3a71b4af0ca5f842f70e8b4dd2701bd4155
Signed-off-by: Philippe Coval <p.coval@samsung.com>
* nucleo-144-f767-netnsh: Add ethernet config
Based on nsh's config
plus stm32f769i-disco/nsh-ethernet
(which should be renamed to align netnsh)
Usage:
mount -t procfs /proc ; ifconfig -a
mkdir /tmp ; mount -t tmpfs /tmp
ifdown eth0
ifconfig eth0 hw 00:80:E1:34:ff:ff; ifconfig
ifup eth0; renew eth0 ; ifconfig
ping 8.8.8.8 ; ping ifconfig.me
cd /tmp/ ; wget http://ifconfig.me/ip ; cat ip
Change-Id: If7da7f33da8676726c42bce41077faf956b99701
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
drivers/lcd/tda19988.c: Numerous changes for a clean compilation.
drivers/lcd/tda19988: Bring in the final pieces from the FreeBSD TDA19988 driver. The driver is now code complete.
drivers/lcd/tda19988.c: Flesh on EDID read logic (still not complete). Add unlink shutdown logic.
drivers/lcd/tda19988.c: Add logic to read one EDID block.
drivers/lcd/tda19988.c: Add tda19988_read_edid() interface. Flesh read() and seek() methods.
drivers/lcd/st7032.c: Fix another error in seek method: Does not account for negative offsets!
drivers/lcd/tda19988.c: Add basic IOCTL infrastructure to support configuratin the video mode. Mostly just a framework for now.
drivers/lcd/tda19988.c: Add more register definitions. Encode page+address in the same was as FreeBSD.
drivers/lcd/tda19988.c: Add support for CEC messaging.
drivers/lcd/tda19988.c: Implement the unlink method. No IOCTLs defined yet.
drivers/lcd/tda19988.c: Add placeholders for missing character driver methods.
drivers/lcd/tda19988.c: Trivial interface improvement to permit reading multiple TDA19988 registers.
drivers/lcd/tda19988.c: Feeble start of TCA19988 drivers. Consists of lower half interface definition and some I2C helper functions. Nothing more.
configs/stm32f4discovery: Update rndis configuration
Add NFS and adjusted stack size for usermain and telnetd client.
Add support for loadable application and ping.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva/cc13xx: Trim code now kind of looks like NuttX code. But does not yet compile.
arch/arm/src/tiva/cc13xx: The first few, feeble steps toward getting the overall trim files compatible with the requirements of the NuttX coding standard.
arch/arm/src/tiva/cc13xx: Replace last of TI hardware access macros with NuttX hardware access macros.
arch/arm/src/tiva/cc13xx: Change TI HWREGB to NuttX getreg8 or putreg8 in trim logic.
arch/arm/src/tiva/cc13xx: Change TI HWREGBITW to NuttX getreg32/putreg32 sequence in trim logic.
arch/arm/src/tiva/hardware/cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Completes the DDIO OSC header file.
cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Updated, but still not finished.
arch/arm/src/tiva/hardware/cc13x2_cc26x2/cc13x2_cc26x2_ddi0_osc.h: Add DDI0 OSC header file. Still a work in progress. Does not yet conform to the NuttX coding standard.
Change _M and _S to _MASK and _SHIFT.
Some minor improvements.
Clean up typos in some comments.
Run all new files against tools/indent.sh
arch/arm/src/tiva/cc13xx: Bring in trim files from SDK. Convert to C-style comments, lowercase hex contants. Remove Windows-style line endings.
I still observe data abort crash if I compile the code with optimization enabled.
The next steps are to investigate the optimization issue and add Watchdog module. Currently, NSH does not run for a long time ;)
arch/arm/src/am335x/am335x_irq.c: Correct interrupt processing routine
configs/beaglebone-black/nsh/defconfig: Enable debug compilation options. Otherwise data abort crash is observed
arch/arm/src/am335x/am335x_lowputc.c and arch/arm/src/am335x/chip/am335x_uart.h: UART-related cosmetic changes
arch/arm/src/am335x/am335x_timerisr.c: Make sure that Timer 1 interrupts are disabled before any access to peripheral registers
stm32f0l0: SPI and GPIO EXTI support
arch/arm/src/stm32f0l0: add support for GPIO EXTI
configs/nucleo-l073rz: support for nrf24l01
configs/b-l072z-lrwan1/include/board.h: add note about onboard Murata CMWX1ZZABZ-09 module and definitions for available peripherals
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
fs/littlefs: Fix some compilation errors.
fs/littlefs: Brings code a little closer to NuttX coding standard. Not 100%, but closer.
fs/littlefs: Convert all C++ style comments to C comments.
Author: lihaichen <li8303@163.com>
fs/littlefs: Adds port of the mbed littlefs.
depends on !DISABLE_MOUNTPOINT && MTD_BYTE_WRITE
register_mtddriver("/dev/w25", mtd, 0755, NULL);
mount("/dev/w25", "/w25", "littlefs", 0, NULL);
