Adds board definition for imx93-evk board
- Support for the Cortex-A55 core in i.MX93, support for the Cortex-M33
core is _not_ provided
- "nsh" profile is provided, this includes a minimalistic feature set
which boots the SoM to nsh console
- A bootloader is required, u-boot has been tested
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Current `CONFIG_PAGING` refers to an experimental implementation
to enable embedded MCUs with some limited RAM space to execute
large programs from some non-random access media.
On-demand paging should be implemented for the kernel mode with
address environment implementation enabled.
This patch update documents to reflect the fact that remote node is kicked
off by master node. It also adds debug dump to aid the MISA reading issue
investigation.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Add documentation about the RMT peripheral (and using it to drive
WS2812 addressable RGB LEDs) for ESP32-S2, ESP32-S3, ESP32-C3,
ESP32-C6 and ESP32-H2.
This adds initial document for using TMPFS based on my short experience,
hoping to save people's time on guessing how to use.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
"
I used
cd nuttx
cmake -B build -DBOARD_CONFIG=stm32f401rc-rs485:nsh -GNinja
to config
and when following the instruction in this official websites I found the
command to use cmake to build the target is wrong.
which is "cmake --build build -t menuconfig" also wrong the output dir
"build/nuttx".
and by the way, In my practice I find the bin file and elf file is not
in build/nuttx but in build/. So I changed these. But I'm not 100% sure
that my fix is right as I'm a beginner, but what I fix works fine in my
computer. This is my first PR to the public doc. My fix maybe totally
wrong as I am not get into the nuttx, just following the instruction and
encountered some mistakes.
thx for reviewing
"
K230 chip has two T-Head C908 RiscV cores, previously we run NuttX
on either little or big cores. This patch runs NuttX on both cores
with OpenAMP support via the RPTUN driver.
New additions:
- in arch/risc-v/src/k230
- k230_rptun.c K230 RPTUN driver
- k230_rptun.h K230 RPTUN driver header file
- in baords/risc-v/k230/canmv230
- configs/master Build config for master node
- configs/remote Build config for remote node
- scripts/ld-rptun.script Build script for RPTUN
Major changes:
- arch/risc-v/Kconfig Select NUTTSBI_LATE_INIT upon NUTTSBI
- in arch/risc-v/include
- k230/irq.h Add UART3 IRQ defs
- in arch/risc-v/src/k230
- Kconfig Add RPTUN related config items
- Make.defs Add k230-rptun.c to sources
- hardware/k230_memorymap.h Add K230 device and CSR defs
- k230_hart.c Add hart ctrl for RPTUN
- k230_hart.h Add hart ctrl for RPTUN
- k230_mm_init.c Add Svpmbt to support RPTUN
- k230_start.c Revised to support RPMsg UART
- in boards/risc-v/k230/canmv230
- scripts/Make.defs Add RPTUN script selection
- src/canmv_init.c Add RPTUN and RPMsg_UART initialization
- in Documentation/platforms/risc-v/k230/boards/canmv230
- index.rst Add AMP usage information.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
This adds support for creating an early frame buffer and primatives for
writing to this frame buffer as a console. This does require the font
infrastructure as well as multiboot2.
Additionally this can now be used with a UEFI bootloader long as it
boots NuttX via Multiboot2. There does seem to be a PCI interrupt
issue when running in UEFI mode.
I was able to boot my laptop using this and see PCI devices enumerate.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
x86_64: Add conditionals around the multiboot framebuffer
Squashed commits:
1. Porting prior PCI work in place of jailhouse code
At this point the PCI enumeration works for x86_64 including over
pci-pci bridges.
Running QEMU with this configuration we see the bridge and the
device on the bridge. It also detected the qemu test device
qemu-system-x86_64 \
-cpu host,+pcid,+x2apic,+tsc-deadline,+xsave,+rdrand \
--enable-kvm -smp 1 -m 2G -cdrom boot.iso --nographic -no-reboot \
-device pci-testdev \
-device pci-bridge,id=bridge0,chassis_nr=2 \
-device e1000,bus=bridge0,addr=0x3
qemu_pci_init: Initializing PCI Bus
pci_probe_device: [00:00.0] Found 8086:1237, class/revision 06000002
pci_probe_device: [00:01.1] Found 8086:7010, class/revision 01018000
pci_probe_device: [00:01.2] Found ffff:ffff, class/revision ffffffff
pci_probe_device: [00:01.3] Found 8086:7113, class/revision 06800003
pci_probe_device: [00:01.4] Found ffff:ffff, class/revision ffffffff
pci_probe_device: [00:01.5] Found ffff:ffff, class/revision ffffffff
pci_probe_device: [00:01.6] Found ffff:ffff, class/revision ffffffff
pci_probe_device: [00:01.7] Found ffff:ffff, class/revision ffffffff
pci_probe_device: [00:02.0] Found 1234:1111, class/revision 03000002
pci_probe_device: [00:03.0] Found 8086:100e, class/revision 02000003
pci_probe_device: [00:04.0] Found 1b36:0005, class/revision 00ff0000
pci_probe_device: [00:04.0] Probing
pci_check_pci_bridge: [00:05.0] Found Bridge
pci_probe_device: [01:03.0] Found 8086:100e, class/revision 02000003
pci_probe_device: [00:05.0] Found 1b36:0001, class/revision 06040000
2. Remove unused CONFIG_PCI_MAX_BDF option
3. Add a workaround for Jailhouse pci scanning
4. Extend BAR parsing and handle PIO and MMIO for pci-testdev
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
5. PCI: Add initial support for QEMU 'edu' test device
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
6. Bring up PCI later in boot process
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
7. Add ISR and DMA support to QEMU edu test pci device
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
8. Fix bad function prototype definition in qemu_edu
9. intel64: Add a pci test configuration and instructions
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
10. PCI: Fix issue in identification of 64bit bar
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
- spi/slave.h: revise comments in pulic types section
- doc/sim.rst: minor formatting, add ways to escape cu
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
USART peripheral can work in SPI mode as well. This commit adds support
for such functionality. Only 1 slave device is supported by the
peripheral therefore board level does not have to ensure correct CS
setup.
The usage of the peripheral is the same as with other SPI drivers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This slightly revised the USB host documentation and fixed typos
encountered in the document and some source files.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Changes:
- Documentation/platforms/risc-v/k230 revised for both modes
- arch/risc-v/include/k230/irq.h add S-mode IRQs
- under arch/risc-v/src/k230 folder:
- Make.defs drop use of k230_exception_m.S
- hardware/k230_clint.h add S-mode defs, revised freq
- k230_head.S unified flat/kernel mode support
- k230_irq.c add S-mode support with debug dump
- k230_mm_init.c revised for K230 S-mode
- k230_start.c revised for flat/s-mode,
- arch/risc-v/src/k230/k230_timerisr.c unified flat/s-mode support.
- under boards/risc-v/k230/canmv230 folder:
- configs/nsh/defconfig fix RAM size
- include/board_memorymap.h cleanup for S-mode
- src/.gitignore ignore romfs_boot.c
- src/Makefile add romfs support
Renames:
- under boards/risc-v/k230/canmv230/src/ folder:
- canmv_init.c from k230_appinit.c making room for more k230 devices
Dropped:
- under arch/risc-v/src/k230/
- k230_exception_m.S as hybrid mode not ready yet.
New files in boards/riscv/k230/canmv230:
- configs/knsh/defconfig S-mode config
- scripts/ld-kernel.script S-mode linker script
- src/romfs.h User space ROMFS defs needed in S-mode
- src/romfs_stub.c Stub ROMFS image
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
The code is mainly derived from the NuttX qemu-rv/rv-virt codebase.
Major changes:
- boards/Kconfig: add new BOARD_K230_CANMV
- arch/risc-v/Kconfig: add new CHIP_K230 chip and ARCH_RV_MMIO_BITS
- arch/risc-v/src/common/riscv_mtimer.c: use ARCH_RV_MMIO_BITS to
select MMIO access width
New additions:
- arch/risc-v/include/k230/: k230 SoC definitions
- arch/risc-v/src/k230/: k230 SoC sources
- boards/risc-v/k230/canmv230/: CanMV-K230 board sources and configs
- Documentation/platforms/risc-v/k230/: simple doc
Note that only FLAT build works for canmv230 now.
This PR has changes in RiscV common layer thus may affect other RiscV ports
It changes the mtime/mtimecmp access control from using config ARCH_RV64 to
newly intorduced config ARCH_RV_MMIO_BITS.
Original design uses ARCH_RV64 to select 64bit MMIO in riscv_mtimer.c, this
can't cope with the situation with K230 --- it has ARCH_RV64 but only can do
32bit MMIO. So a new ARCH_RV_MMIO_BITS config has been introduced. Its value
depicts the MMIO width in bits. The MMIO_BITS defaults to 32/64 for RV32/
RV64 respectively. This allows the macro to replace current use of ARCH_RV64
in riscv_mtimer.c.
The new MMIO_BITS config is a derived one, and for RiscV chips with
equal CPU and MMIO widths there is no need to explicitly set it as the
default rule will do that. Only chips with different CPU and MMIO widths
need set it in Kconfig.
So by design this change should be safe but RiscV ports should be checked.
"ostest" verification has been done for:
- canmv230/nsh
- rv-vivt/nsh
- rv-virt/nsh64
configuration generation and manual check of derived RV_MMIO_BITS has been
done for:
- star64/nsh
- arty_a7/nsh
- bl602evb/nsh
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This PR adds support for PINE64 Ox64 64-bit RISC-V SBC, based on Bouffalo Lab BL808 SoC (T-Head C906 Core). Most of the code is derived from NuttX for Star64 JH7110. The source files are explained in the articles here: https://github.com/lupyuen/nuttx-ox64
### Modified Files
`boards/Kconfig`: Added Ox64 board
### New Files in boards/risc-v/bl808/ox64
`src/bl808_appinit.c`: Startup Code
`include/board.h`: Ox64 Definitions
`include/board_memorymap.h`: Memory Map
`src/etc/init.d/rc.sysinit`, `rcS`: Startup Script
`src/.gitignore`: Ignore the tmp filesystem
`scripts/ld.script`: Linker Script
`scripts/Make.defs`: Ox64 Makefile
`src/Makefile`: Ox64 Makefile
`Kconfig`: Ox64 Config
`configs/nsh/defconfig`: Build Config for `ox64:nsh`
### Updated Documentation
`platforms/risc-v/bl808/index.rst`: New page for Bouffalo Lab BL808 SoC
`platforms/risc-v/bl808/boards/ox64/index.rst`: Building and booting NuttX for Ox64
`platforms/risc-v/jh7110/boards/star64/index.rst`: Fix typo
ignore known warnings:
/home/raiden00/git/RTOS/nuttx/nuttx/Documentation/reference/os/netdev.rst:61: WARNING: Duplicate C declaration, also defined at reference/os/netdev:39.
Declaration is '.. c:struct:: net_driver_s'.
/home/raiden00/git/RTOS/nuttx/nuttx/Documentation/reference/user/07_signals.rst:180: WARNING: Duplicate C declaration, also defined at reference/user/structures:112.
Declaration is '.. c:struct:: sigaction'.
There are ICs available on the market that integrate various power inverter
features. The driver for such a device must be tightly coupled to a FOC device
as using it as a separate device doesn't make sense.
Summary:
- Upgraded to xpack-riscv-none-elf-gcc-12.3.0-2 to resolve symbol recognition
issues in riscv-none-elf-gdb, as reported in
https://github.com/xpack-dev-tools/riscv-none-elf-gcc-xpack/issues/22.
Impact:
- Expected to enhance toolchain stability with no negative side effects.
Testing:
- Verified with rv-virt:netnsh and rv-virt:netnsh64 configurations
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Copyright notice and author contact/information should not be included
in file header anymore. Only standard Apache 2.0 licensing information
should be used.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Documentation/legacy_README.md:675: WARNING: duplicate label introduction/resources:installation, other instance in Documentation/introduction/resources.rst
testing badges
Converted legacy readme from .md to .rst
Revert "Converted legacy readme from .md to .rst"
This reverts commit e33fef7a5aaa5dd377f87b90a667a2704b9fb834.
- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
