imxrt_gpioirq.c
- Add check for interrupt mask register before dispatching ISR. The GPIO_ISR bits are set independent of the GPIO_IMR bits.
imxrt_irq.c
- fixed a range check for extint in function imxrt_irqinfo().
Squashed commit of the following:
arch/arm/src/kinetis: Add K28F memory map.
arch/arm/src/include/kinetis and src/kinetis: Add basic chip features and interrupt-related definitions for the K28F
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Fix some spacing
arch/arm/src/tiva: Verify that the EEPROM driver at least builds.
arch/arm/src/tiva: Move unused function added to tm4c129_syscontrol.c to tiva_eeprom.c where it is actually used.
arch/arm/src/tiva: Reorganize EEPROM register definitions so that the file organization is more like other platforms.
arch/arm/src/tiva: Trying to resolve EEPROM register addressing. Still some issues.
arch/arm/src/tiva: Ran uncrustify on tiva_eeprom.c
arch/arm/src/tiva: EEPROM driver is a little closer to coding standard. Still a way to go.
Author: Shirshak Sengupta <sgshirshak@gmail.com>
arch/arm/src/tiva: Implemented EEPROM driver in compliance with MTD driver as provided by NUTTX for TM4C1294. The EEPROM driver needs to be initialized by calling the function tiva_EEPROMInit The EEPROM driver currently supports only two functionalities - read bytes(multiple of 4) and write bytes (multiple of 4). Note - Rest of the features of EEPROM will be implemented in the future.
kinetis usb device fixes
* kinetis:usb device use correct CONFIG OTG control
* kinetis:usb device fix interrupt storm when cable is disconnected
The DM, DP state were incorrect because the pulldowns were not
enabled.
Also the pending asynchronous resume interrupt needed to be
re-armed after the suspend is in effect. This is now done in
the isr.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Update README.
configs/or1k: Should include header file file where exported functin is prototyped.
arch/or1k/src: Eliminate some warnings.
arch/or1k: Complete review
Fix some recently introduced build issues
configs/or1k/nsh: Convert to proper, compressed defconfig file.
Another README update.
Update README
configs/or1k: Updates from initial review.
Update README.
Author: Matt Thompson <matt@extent3d.com>
or1k: Added configurable CPU frequency to Kconfig. Calculate tick timer match period based on configured frequency.
OpenRISC: Enable instruction and data cache
OpenRISC: Initial support.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
include/nuttx/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
drivers/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
configs/photon: Cosmetic, coding standard changes from review of last merge.
arch/arm/src/stm32: SDIO changes from last review: Fix a few long lines and other coding standard issues; Make additions for SDIO card support dependent on a configuration option.
Author: hhuysqt <hyq9606@126.com>
Return IEEE 802.11 MAC address just as ethernet does
Modifyed bcmf_board_setup_oob_irq declaration
Modified OOB ISR function types
Add some logic according to WICED SDK
Bug fixed: data_offset counts in 4-bytes
Add BCM43438 logic for future developement
Add tips on using telnet
Use SDIO in-band interrupt instead of OOB interrupt, because Photon seems to unconnect the OOB interrupt line...
add SDIO in-band interrupt logic
drivers/1wire: add PM hooks and unlink support to sht21 sensor (allowing hot-swappable I2C bus from 1-wire converter)
* drivers/1wire: add PM hook to 1wire bus
* drivers/1wire/ds28e17.c: i2c instance must be zeroed
* drivers/sht21: add unlink support
Unlike most other unlink implementations in NuttX drivers, this one
does not allow any I2C operations after unlink, making it possible to
deallocate the I2C bus.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
