Fixed coding standard error in several files. Use of while( is incorrect; a space is required between while and (. Also ran tools/nxstyle and fix thoses complaints as well in most files.
Changes to comply with coding standard. Mostly focused on files with missing space after keyword in if(, switch(, and for(. Offending files also got changes to comply with tools nxstyle. If there were logs of nxstyle complaints, the file also got a taste of tools/indent.sh. Still need to fix occurrences of while( with missing space. There are a lot of them.
Squashed commit of the following:
arch/arm/src/stm32f0l0: Various changes for a clean compilation. Still does not compile correctly due to missing FLASH latency definitions.
arch/arm/src/stm32f0l0/hardware: Add framework for the STM32 L0. Currently set to same as the STM32F0.
arch/arm/src/stm32f0l0/hardware: Very fragmentary FLASH header register definitions for the STM32 L0.
arch/arm/src/stm32f0l0: Bring in DMA v1. Cannot possibly be functionaly yet due to the limited number for M0 interrupts.
arch/arm/src/stm32f0l0: Add STM32 F0/L0 LSE and backup power domain controls.
arch/arm/src/stm32f0l0/hardware/stm32l0_pwr.h: Add STM32L0 PWR header file.
arch/arm/include/stm32f0l0/chip.h: Clean up WIP chip header file.
arch/arm/include/stm32f0l0/chip.h: WIP.
arm/src/stm32f0l0: Resolve some small differences between F0 and L0 GPIO pin options.
arch/arm/src/stm32f0l0: Better integrate STM32L0 header files.
nuttx/arch/arm/include/stm32f0l0: Add STM32L0 IRQ number definition file.
arch/arm/src/stm32f0l0: Add STM32L0 RCC driver.
arch/arm/src/stm32f0l0/hardware: Adds basic STM32L0 header files.
arch/arm/src/stm32f0l0: Add STM32L0 chip selections.
configs/: Hook new STM32L0 boards into the configuration system.
configs: nucleo boards use as default ST LINK MCO as clock input from MCU and for this HSEBYP must be enabled
configs: add basic support for nucleo-l073rz
configs: add basic support for b-l072z-lrwan1
Master
configs/nucleo-f334r8: add example for the SPWM generation (custom STM32 PWM usage)
arch/arm/src/stm32/stm32_pwm: fix compilation errors if the upper-half PWM logic is not enabled
include/nuttx/drivers/pwm.h: remove dependency on CONFIG_PWM for the upper-half PWM header. This allows compilation for the lower-level PWM drivers even if the upper-half PWM logic is not used.
arch/arm/src/stm32/stm32_tim.c: fix compilation error if there is no TIM8
configs/nucleo-f334r8/highpri: remove the upper-half ADC from configuration
configs/nucleo-f302r8/highpri: remove the upper-half ADC from configuration
configs/stm32f429i-disco/highpri: remove the upper-half ADC from configuration
Approved-by: GregoryN <gnutt@nuttx.org>
Improvements in STM32 ADC
arch/arm/src/stm32/stm32_adc.c: start conversion on startup is now possible if TIM triggering selected. This can be useful to start ADC TIM conversion for ADC IPv2 when opening ADC device.
arch/arm/src/stm32/stm32_adc.c: fix compilation errors for chips with one ADV TIM
configs/nucleo-f303re: refresh ADC example
configs/nucleo-f334r8: refresh ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
configs/nucleo-f207zg, configs/nucleo-f103rb: add ADC and PWM examples; arch/arm/src/stm32_adc.c: there is no DMA CFG bit for the basic IPv1 ADC
Approved-by: GregoryN <gnutt@nuttx.org>
Improvements in STM32 ADC, minor changes in STM32 PWM, DMA, HRTIM and add some highpri ADC examples
arch/arch/src/stm32/stm32_adc: fix RCC reset logic
arch/arch/src/stm32/stm32_adc: move sample time change functions to low-level ADC ops
arch/arch/src/stm32/stm32_adc: configurable ADC DMA mode (one shot mode, circular mode)
arch/arch/src/stm32/stm32_pwm: remove llops_get interface. We can use structure casting to get pwm low-level ops
arch/arch/src/stm32/stm32_pwm: add timer enable/disable and frequency update to low-level ops
arch/src/arm/stm32: remove redundant stm32f33xxx_dma.c
arch/arm/src/stm32/stm32f40xxx_dma.c: add interfaces to interact with highp priority DMA interupts
arch/src/arm/stm32/stm32_hrtim: do not enable timers on startup if option from Kconfig selected and add interface to enable/disable timers
arch/src/arm/stm32/stm32_hrtim: fix some warnings
configs/nucleo-f334r8/highpri: update configuration due to changes in stm32_adc
configs/stm32f334-disco/buckboost: update configuration due to changes in stm32_adc
configs/nucleo-f334r8/highpri: add support for ADC injected sequence, add triggering from TIM1
configs/nucleo-f302r8/highpri: add high priority ADC interrupts example
configs/stm32f429i-disco/highpri: add high priority ADC interrupts example
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm: Remove support for CONFIG_ARMV7M_CMNVECTOR. It is now the only vector support available. Also remove CONFIG_HAVE_CMNVECTOR. That no longer signifies anything."
arch/arm/src/stm32: This commit removes support for the dedicated vector handling from the STM32 architecture support. Only common vectors are now supported.
Master
* stm32_hrtim: fix warnings related with RCC
* stm32f33xxx_adc: add some publicly visable interfaces and some code to support injected channels
* stm32f33xxx_dma: add public interface to handle with DMA interrupts
* stm32_hrtim: change some names and add some coments
* chip/stm32f33xxx_adc.h: cosmetics
* nucleo-f334r8: add logic for zero latency high priority interrupts example
* stm32: update some ADC-related configuration in Kconfig
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* stm32f33xxx_adc.c: fix some warnings and compilation error when extsel not in use
* nucleo-f334r8/adc: change serial console to USART2 (STLINK COM)
Approved-by: Gregory Nutt <gnutt@nuttx.org>
