This revises PROTECTED build for qemu-rv mainly to avoid hard-coded
addresses in linker scripts. It also added rv32 support, cleaned up
config `pnsh64` and added config `pnsh`.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This adds NuttSBI support for rv-virt device so that to enable CI
checks for NuttSBI later. It allows using `-bios nuttx` option to
run NuttX with QEMU v6.2 w/o OpenSBI.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This change implements a driver for the two watchdog timers on the BL808, and enables it as part of the timer config. The driver is based on the GP timer driver.
This revises FLAT build ld.script so that to use CONFIG_RAM_START
instead of hard coded address to increase flexibility.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This allows virtio devices to be probed upon board_early_init, thus
making virito-serial ready earlier for console use.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
- This PR adds the LED Driver for QEMU RISC-V 32-bit and 64-bit (User LEDs and Auto LEDs)
- QEMU RISC-V LED Driver will be used by the Rust Blinky App for Google Summer of Code
- Blinking the LED is probably the most common Embedded Demo, and now it's supported by QEMU RISC-V
- We added NuttX Configs `rv-virt:leds` and `rv-virt:leds64` to support User LEDs for 32-bit and 64-bit RISC-V
- Turning on/off a Simulated User LED will print a log message: "LED 1 set to 1"
- The code is derived from NuttX PinePhone LED Driver
This adjusts canmv230 `master` and `remote` configs to support both
k230 and k230d devices and drop unused items.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This revises canm230:pnsh in a few ways:
- adjusting linker scripts structure,
- asserting PMP setting results,
- adjusting configs for both k230d and k230 devices.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This commit implements a character driver for the general purpose ADC of the BL808, based on the hardware scanning functionality. The driver supports setting different conversion resolutions and the order of channels to be scanned via menuconfig.
- This PR adds the LED Driver for Ox64 Board (User LEDs and Auto LEDs)
- Ox64 LED Driver will be used by the Rust Blinky App for Google Summer of Code
- User LED 1 is configured for GPIO 29. Other User LEDs and Auto LEDs shall be configured by the NuttX Dev.
- The code is derived from NuttX PinePhone LED Driver
This revises ld-nuttsbi.script for easier use. It also adjusts
canmv230/nsbi to fit both k230d and k230 devices.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This commit modifies the existing serial driver to add support for the remaining UARTs on the BL808. It also introduces support for setting baud rate, character length, stop bits, parity, flow control and which serial port acts as the console.
This change implements a system for allowing the D0 core (which runs NuttX) to receive forwarded interrupts from the M0 core. This makes it possible for drivers that rely on interrupts to work with peripherals attached to the M0 core.
This PR adds support for Milk-V Duo S 64-bit RISC-V SBC, based on SOPHGO SG2000 SoC (T-Head C906 Core). Most of the code is derived from NuttX for Ox64 BL808. The source files are explained in the articles here: https://github.com/lupyuen/nuttx-sg2000
Modified Files:
`boards/Kconfig`: Added Milk-V Duo S board
`arch/risc-v/src/sg2000/sg2000_timerisr.c`: Fixed MTIMER_FREQ for sleep() to work correctly
New Files in boards/risc-v/sg2000/milkv_duos:
`src/sg2000_appinit.c`: Startup Code
`include/board.h`: Milk-V Duo S Definitions
`include/board_memorymap.h`: Memory Map
`src/etc/init.d/rc.sysinit`, `rcS`: Startup Script
`src/.gitignore`: Ignore the tmp filesystem
`scripts/ld.script`: Linker Script
`scripts/Make.defs`: Milk-V Duo S Makefile
`src/Makefile`: Milk-V Duo S Makefile
`Kconfig`: Milk-V Duo S Config
`configs/nsh/defconfig`: Build Config for `milkv_duos:nsh`
Updated Documentation:
`platforms/risc-v/sg2000/index.rst`: New page for SOPHGO SG2000 SoC
`platforms/risc-v/sg2000/boards/milkv_duos/index.rst`: Building and booting NuttX for Milk-V Duo S
There is no need to use kernel build for S-mode all the time. As cpu
scratch is supported for non kernel mode build, it is possible to use
flat build for S-mode.
Add flat build support for risc-v S mode.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
This provides an alternate tickless scheduling method, which uses the riscv
mtimer as a timebase, allowing the time and timeh registers to used
throughout an application.
The exiting tickless method, using Litex's timer0 has been left in place, as
it is a more performant option, but currently has the potential issue
identified in #11189.