The length of the IROM and DROM segments should be related to the extent
of the address space, and not be limited to the capacity of the External
Flash device.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
* Remove the 'COEXISTENCE' suffix from Wi-Fi's STA + SoftAP mode.
Coexistence usually refers to Wi-Fi + BLE, instead of Wi-Fi's
operation mode;
* Remove commented debug code;
* Remove outdate function descriptions;
Initially supporting ESP32-C3 chip, to be followed by other RISC-V-based
chips from Espressif.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
There is currently a big problem in the address environment handling which
is that the address environment is released too soon when the process is
exiting. The current MMU mappings will always be the exiting process's, which means
the system needs them AT LEAST until the next context switch happens. If
the next thread is a kernel thread, the address environment is needed for
longer.
Kernel threads "lend" the address environment of the previous user process.
This is beneficial in two ways:
- The kernel processes do not need an allocated address environment
- When a context switch happens from user -> kernel or kernel -> kernel,
the TLB does not need to be flushed. This must be done only when
changing to a different user address environment.
Another issue is when a new process is created; the address environment
of the new process must be temporarily instantiated by up_addrenv_select().
However, the system scheduler does not know that the process has a different
address environment to its own and when / if a context restore happens, the
wrong MMU page directory is restored and the process will either crash or
do something horribly wrong.
The following changes are needed to fix the issues:
- Add mm_curr which is the current address environment of the process
- Add a reference counter to safeguard the address environment
- Whenever an address environment is mapped to MMU, its reference counter
is incremented
- Whenever and address environment is unmapped from MMU, its reference
counter is decremented, and tested. If no more references -> drop the
address environment and release the memory as well
- To limit the context switch delay, the address environment is freed in
a separate low priority clean-up thread (LPWORK)
- When a process temporarily instantiates another process's address
environment, the scheduler will now know of this and will restore the
correct mappings to MMU
Why is this not causing more noticeable issues ? The problem only happens
under the aforementioned special conditions, and if a context switch or
IRQ occurs during this time.
PWM driver for multiple peripherals supplied in gateware.
Only single channel frequency and duty cycle control is implemented. Pulse counting and multichannel features are not currently feasible.
Additions also include a new board configuration for arty-a7 which enables the PWM driver and example application.
MCUboot support is no longer behind EXPERIMENTAL for the following
chips:
- ESP32
- ESP32-S2
- ESP32-S3
- ESP32-C3
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Summary:
- This commit adds knetnsh64 and knetnsh64_smp
Impact:
- None
Testing:
- Tested with ping, telnet and iperf on QEMU-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit fixes the CI build errors regressed by
https://github.com/apache/incubator-nuttx/pull/7351
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Currently the IHC (Inter Hart Communication) depends on OpenAMP and
rptun. However, the bootloader portion of the IHC doesn't need
either of them. Now they are wasting a lot of bootloader space.
Reorganize the bootloader portion into a separate file 'mpfs_ihc_sbi.c'.
This file contains the OpenSBI vendor extensions, or the only required
functionalities for the bootloader. On the other hand, 'mpfs_ihc.c'
contains the non-bootloader code.
This patch also makes it possible to utilize 2 RPMSG channels. This
has been tested so that 2 separate NuttXs on harts 1 and 2 communicate
with Linux kernel that runs on harts 3 and 4.
New configuration files are added as well:
- rpmsg-ch1: sample config for RPMSG
- rpmsg-ch2: sample config for another RPMSG channel
- rpmsg-sbi: sample bootloader config for RPMSG/OpenSBI
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- This commit updates README.txt regarding how to build kernel
and apps for BUILD_KERNEL
- Also update on parallel build for BUILD_FLAT
Impact:
- None
Testing:
- Tested with qemu-7.1.0
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds ksmp64 configuration to test BUILD_KERNEL+SMP
- NOTE: README.txt has been updated
Impact:
- None
Testing:
- Tested with QEMU 6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that the OpenSBI library depends on the BSD license
- This commit fixes this issue
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Simplify the clock mode from the board.h -files. Also make the
SD clock definable as well.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Some related products, such as Aries m100pfs, don't support eMMC
speeds up to 200MHz. Thus, provide option to select slower clock.
This has only to do with the clocking, no CMD6 is sent to select
high speed modes.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The underlying hardware supports 9 endpoints:
- EP0
- 4x IN EPs
- 4x OUT EPs
Currently the driver assumes every EP number is unique. This limits
the amount of EPs to 1 + 4 = 5. Utilize the EPs in such a manner
that all may be used.
Also fix a few error handling related bugs. Update the composite
driver to match the current situation as well.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
rename the UDP_BINDTODEVICE to SO_BINDTODEVICE to follow the linux
style to be compatible with non-UDP protocol binding requirements
Signed-off-by: chao.an <anchao@xiaomi.com>
It is not really needed; g_hart_stacks is only used during SBI init as
a temporary stack area. We can use the scratch area buffers for this, as
the scratch areas define almost 4K of extra space, which is used for
exception stacks anyway.
After #6400 the prebuilt bootloader may be used for loading the NuttX
images when BUILD_PROTECTED is enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Sync some of the AXI configuration and DDR training parameters with the manufacturer's
defaults.
The TIP_CFG parameter correction helps with DDR training failures on some individual boards
The AXI end address values fix early random crash in power-on boot on some individual boards
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Linux kernel uses M-mode trap for handling Inter-Hart Communication (IHC).
This patch provides all the required functionalities for this purpose.
Previously, HSS bootloader was required. Now, NuttX is run as the
bootloader providing OpenSBI vendor extensions instead. This setup has
been tested on the following configuration:
- Hart 0 has NuttX in bootloader mode with OpenSBI
- Hart 1 unused
- Hart 2 has NuttX configured at 0xa2000000
- Hart 3 has U-boot / Linux kernel (at 0x80200000)
- Hart 4 has U-boot / Linux kernel (at 0x80200000)
Upon startup, NuttX on hart 0 will initialize SD-card driver, loads
the hart 2 NuttX from the SD-card and loads the U-boot to 0x80200000.
Also the nuttx.sbi -binary is loaded from SD-card into address 0x80000000,
which is also marked as reserved area in the Linux kernel device tree (for
the chuck 0x80000000 - 0x80200000).
Hart 2 NuttX waits until Linux kernel (IHC master) is started. After the
initial handshake, RPMsg / virtIO bus along with the IHC may be used for
proper AMP mode.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- This commit adds hostfs support to nsh and nsh64 defconfigs
Impact:
- None
Testing:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Mappings are done with vaddr=paddr.
- I/O space mapped with two gigapages
- Kernel space mapped to statically allocated page tables. 2MB of kernel
memory is supported.
- Page pool is mapped to the kernel space, to allow virtual memory access
for the kernel e.g. to initialize the page memory when it is allocated.
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Follow: http://glennastory.net/boot/sysinit.html
This is first script that init runs is rc.sysinit. This
script does serval initialization tasks about basic service.
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(Peripherals driver, core driver, ...)->
run rcS script(mount fs, run service) ->
board_appinitialize->
After this patch:
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(core driver,...)->
run rc.sysinit script(mount fs, run core service) ->
board_appinitialize(Peripherals driver)->
run rcS script(run other service)->
So, Peripheral drivers can do more with the file system and
core services.
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
- Add config "ARCH_USE_S_MODE" which controls whether the kernel
runs in M-mode or S-mode
- Add more MSTATUS and most of the SSTATUS register definitions
- Add more MIP flags for interrupt delegation
- Add handling of interrupts from S-mode
- Add handling of FPU from S-mode
- Add new context handling functions that are not dependent on the trap
handlers / ecall
NOTE: S-mode requires a companion SW (SBI) which is not yet implemented,
thus S-mode is not usable as is, yet.
RISC-V GCC is configured with --enable-initfini-array so it emits an
.init_array section instead of .ctors
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
## Summary
`esp32c3_spi2_cmddata()` implements SPI Cmd/Data `SPI_CMDDATA()` for only 3 LCD drivers: ST7735, ST7789 and GC9A01.
This patch removes the check for LCD drivers, so that SPI Cmd/Data will work for all LCD drivers.
More details: https://github.com/apache/incubator-nuttx/pull/5898
## Impact
This change impacts LCD drivers that call `SPI_CMDDATA()`.
Previously `SPI_CMDDATA()` would fail with `ENODEV` for LCD drivers other than ST7735, ST7789 and GC9A01.
After patching, `SPI_CMDDATA()` will work correctly with all LCD drivers.
## Testing
This is a minor patch so no testing is needed.
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Move the target specific memory map to a separate file so there is no
need to copy&paste the __xxram_start etc linker symbols to each file
that needs them.
Also add MMU flags for I/O and kernel areas, they will be needed
when the kernel runs with virtual addresses also.
Mux USB IO pins one-by-one using package specific pinmux definitions. This avoids accidentally overwriting IO settings for other pins.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a simple USB device driver for the mpfs. However,
this driver is still at its early phase. Only limited testing
with CDC/ACM has been conducted.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
## Summary
A lot of linker scripts were listed twice, once for unix, once for windows.
This PR cleans up the logic so they're only listed once.
## Impact
Any opportunity to use a single source of truth and reduce lines of code is a win!
## Testing
CI will test all build
Summary:
- Apply the same style as sabre-6quad
Impact:
- None
- NOTE: esp32c3-devkit still remains old style because of link errors
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
since the related code was removed by:
commit 4d5a964f29
Author: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
Date: Tue Feb 23 18:04:13 2021 +0800
net: unify socket into file descriptor
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The image must be placed into:
boards/risc-v/mpfs/icicle/include/boot_romfsimg.h
The image is mounted by mpfs_bringup, which is run by the application
itself, or by board_late_initialize() in the case when
CONFIG_BOARD_LATE_INITIALIZE is defined, e.g. with CONFIG_BUILD_KERNEL
NOTE: THIS ONLY WORKS WHEN KERNEL RUNS IN M-MODE FOR NOW
This frees the PMP for other use, e.g. HART memory separation.
The page tables are statically allocated, 1 per level.
This feature is now behind CONFIG_MPFS_USE_MMU_AS_MPU, because
only the MPFS target supports this (others are not tested).
If the MMU is used for memory separation within a HART, the PMP must
still be configured to allow user access to the memory mapped for the
HART, because PMP *rekoves* access by default. At this point all of
the user memory as well as the kernel RAM are opened.
A more flexible solution for PMP configuration will follow.
The old implementation used the default ld.script for the kernel side
which did not obey the memory.ld limits whatsoever.
Also, provide the user space addresses from the linker script to get rid
of the pre-processor macros that define (incorrect) default values for
the user space composition.
Some of the configuration options have changed, so update this
config file accordingly.
In this example config, the following hart configuration takes
place:
hart1: 0xafb00000 (Another NuttX)
hart2: unused
hart3: 0x80200000 (u-boot and Linux kernel)
hart4: 0x80200000 (u-boot and Linux kernel)
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
There is no such section. Instead, place the object mpfs_head.o at the start of
the text.
Put mpfs_head.o directly into the arch library; there is no need to define
it separately in HEAD_ASRC.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Add the rest of the OpenSBI code to .text.sbi -section. They belong
to there. This frees up some space in the very limited eNVM.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
