Gregory Nutt
ba55e8c7d8
SAMV7: Add RTC register definition header file
2015-06-16 07:23:47 -06:00
Gregory Nutt
c76a1f92c2
SAMV7: Add MCAN register definition header file
2015-06-15 11:37:59 -06:00
Gregory Nutt
416af1b54f
Update README
2015-05-13 13:30:26 -06:00
Gregory Nutt
5b687f4b0f
Fix several defien -> define. Thanks Pierre
2015-05-13 06:33:17 -06:00
Gregory Nutt
c4db8e440d
SAMV7 TWIHS: Fix logic that performs multi-message tranfers with and without repeated starts. This change is the final piece that was required to get the maXTouch Xplained Pro workding.
2015-05-12 17:56:35 -06:00
Gregory Nutt
8f0fb36f11
In go_os_start that sets the IDLE thread stack coloration, mov does not set condition codes which are tested by the following beq. Need to use movs instead. Noted by David Sidrane
2015-05-07 20:36:08 -06:00
Gregory Nutt
55ac01399b
Correct some cloned typos involving EHCI
2015-04-27 14:03:24 -06:00
Gregory Nutt
0092f79696
Two r's and only two r's in the word interrupt
2015-04-23 14:04:43 -06:00
Gregory Nutt
068fc43170
Revert commit b80e8be652dfa52e97daa65aa3e550cf31cb2409
2015-04-12 06:26:50 -06:00
Gregory Nutt
63c0de86fe
Remove all traces of CONFIG_ARMV7M_STACKCHECK
2015-04-11 10:01:44 -06:00
Gregory Nutt
2aa80e06f5
Remove executable flag from more .c and .h files
2015-04-09 08:20:57 -06:00
Gregory Nutt
e113be1bff
SAMA5 Serial: Reading IMR and disabling interrupt must be atomic
2015-04-08 15:27:31 -06:00
Gregory Nutt
2a9bd3ad73
SAM3/4 and SAMV7 UART: The IMR register is read-only. This means that sam_restoreints() does not actually re-enable UART interrupts.
2015-04-08 15:04:10 -06:00
Gregory Nutt
662757c77a
SAM3/4 and SAMV7 Serial: Serial interrupts left disabled.
...
A side-effect of changing serial settings via TERMIOS (such as tcsetattr) is that serial interrupts were being left disabled. This is not a problem if the serial configuration is changed when there are no open references to the serial device. In that case, serial interrupts are disabled and will not be enabled enabled until the serial device is first opened. But it is fatal if the serial device is already opened and if there is a task waiting to receive data. In that case, the side-effect of disabling interrupts is fatal: That task is then left hanging with interrupts disabled.
2015-04-08 14:14:01 -06:00
Gregory Nutt
16814e2b00
Make some file section headers more consistent with standard
2015-04-08 08:04:12 -06:00
Gregory Nutt
65d9d18159
Minor changes to SAMV7 USB register definition file from review
2015-04-06 13:00:48 -06:00
Gregory Nutt
0c40f93c42
SAMV7 USB device: Finish option to force full speed mdoe
2015-04-06 10:07:12 -06:00
Gregory Nutt
fca4c51420
Update comments and README
2015-04-05 07:22:46 -06:00
Gregory Nutt
cf4bbae526
SAMV7: Fix SDRAM initialization instabiilties by changing the order of initialization
2015-04-04 19:58:31 -06:00
Gregory Nutt
c1886c6181
SAMV7: Apparently the data sheet is wrong, SDRAM clocking must be enabled at the PMC or the SDRAM does not work! The data sheet says that there is no clock control for SDRAMC
2015-04-04 19:04:29 -06:00
Gregory Nutt
8aeaff1e95
SAMV7: Fix a errort in GPIO bit encoding. Correct naming of a variable
2015-04-04 16:54:53 -06:00
Gregory Nutt
fda98ebeab
SAMV7: Fix typo in some GPIO definitions
2015-04-04 14:04:58 -06:00
Gregory Nutt
0cf5088475
SAMV71-XULT ILI9488 LCD driver is code complete but untested
2015-04-03 16:36:58 -06:00
Gregory Nutt
b72cf3366c
SAMV7: Add SMC register definition header file; SAMV71-Xult: Add an LCD driver. The initial commit is simply the SAVM4E-EK ILI9375 driver will bogus name changes to ILI9488.
2015-04-03 10:28:32 -06:00
Gregory Nutt
eb21ad0cf2
SAMV71-XULT: Add option to support connection of the maXTouch Xplained Pro on the 50-pin LCD connector
2015-03-31 09:01:38 -06:00
Gregory Nutt
8aa133029f
SAMV7 Ethernet: Fix a write-past-end-of-buffer and trash-the-heap problem
2015-03-29 16:45:05 -06:00
Gregory Nutt
dab3dbc75b
Cortex-M7: Add support for enabled the D-Cache in write only mode.
...
SAMV7 Ethernet: I- and D-Cache are now enabled in the netnsh/ configuration. D-Cache is enabled in write-though mode. This mode is necessary because the DMA descriptors are each 8-bytes in size but the D-Cache cache line is 32-bits in size. So it is impossible make coherency for every 8-byte DMA descriptor without write-through.
2015-03-29 14:42:03 -06:00
Gregory Nutt
4593fe3797
SAMV7/Cortex-M7: Add support for write through D-Cache. SAMV7 Ethernet look like it needs this
2015-03-29 13:09:22 -06:00
Gregory Nutt
a60fa12e86
Clean up pointer handling to make code more readability. This re-introduces the compiler optimization problem but this is the correct thing to do. I will have to drop back from -Os to -O2.
2015-03-28 14:46:35 -06:00
Gregory Nutt
d2fd139ebc
SAMV7 EMAC: Fix alignment issue: RX buffers need to be invalidated. This means the alignment of buffers must be at least to the data cache line size at both ends of the buffer
2015-03-28 13:09:01 -06:00
Gregory Nutt
d7dbdfef58
SAMV7 EMAC: Sometimes TX is not started when TSTART is set??? Workaround seems to be to set it twice. Restored full optimization. Also CONFIG_NET_NOINTS is set so that interrupt level provessing is avoided
2015-03-28 09:42:45 -06:00
Gregory Nutt
79734c3c13
SAMV7 Ethernet: Fix some errors in circular queue handling
2015-03-27 13:04:43 -06:00
Gregory Nutt
66670c1738
SAMV7 Ethernet+USB Updates
2015-03-27 10:47:03 -06:00
Gregory Nutt
3c433f7f35
Updated comments/README
2015-03-26 12:33:03 -06:00
Gregory Nutt
6f4116add0
SAMV6 USB updates
2015-03-26 09:49:01 -06:00
Gregory Nutt
0ec1407add
SAMV7 USB: Move clock initialization back to sam_clockconfig.c; add seperate UTMI register definition header file; fix a couple of typo bugs
2015-03-26 07:56:26 -06:00
Gregory Nutt
8bce3f19d8
SAMV7 USB: Replace 0 with something a little more informative
2015-03-25 18:59:59 -06:00
Gregory Nutt
3568dcd22f
SAMV7 USB: Add some conditioned out test code
2015-03-25 18:45:04 -06:00
Gregory Nutt
8a9d5aa465
Add UTMI register definitions
2015-03-25 18:09:41 -06:00
Gregory Nutt
8b1475665c
SAMV7 USB: More changes
2015-03-25 17:19:36 -06:00
Gregory Nutt
dd06cef845
SAMV7 USB: more updates
2015-03-25 15:56:10 -06:00
Gregory Nutt
2b3aee6940
SAMV7 USB DCD: A few more fixed from early intergration. Still does not work
2015-03-25 09:04:51 -06:00
Gregory Nutt
7e69535daf
SAMV7 USB: More fixes at beginning of testing. Still a long way from working
2015-03-25 08:06:59 -06:00
Gregory Nutt
6ef2911dbf
SAMV7 USB DCD is code complete and ready for test
2015-03-24 14:30:53 -06:00
Gregory Nutt
9a79129dd4
SAMV7 USB: Updates to interrupt handling logic
2015-03-24 14:07:20 -06:00
Gregory Nutt
2b8853f4fd
SAMV7 USB: Updates to endpoint configuration logic
2015-03-24 11:19:34 -06:00
Gregory Nutt
c0c92411ce
SAMV7 USB: Updates to early initialization logic
2015-03-24 10:05:21 -06:00
Gregory Nutt
3875e86436
SAMV7: Add framework for USB DCD. Initial check-in is just the SAMA5 USB DCD with naming changes to get a clean compilation. Needs careful review and comparison with datasheet and, of course, testing
2015-03-23 14:06:53 -06:00
Gregory Nutt
5ed5187175
PIC23MX Starter Kit: Looks like we need to use a different linker script with Pinguino
2015-03-21 15:40:22 -06:00
Gregory Nutt
b41738ed62
SAMV7: A little more USB-related stuff
2015-03-21 08:54:01 -06:00
