arch/arm/src/tiva: Add GPIO IRQ stubs for clean compile
arch/arm/src/tiva/cc13xx: Add build framework for CC13xx GPIO interrupts. Change prototypes of some GPIO IRQ interfaces so that the function prototype is common between LM3S, LM4F, TM4C, and CC13xx.
Master
configs/nucleo-f334r8: add example for the SPWM generation (custom STM32 PWM usage)
arch/arm/src/stm32/stm32_pwm: fix compilation errors if the upper-half PWM logic is not enabled
include/nuttx/drivers/pwm.h: remove dependency on CONFIG_PWM for the upper-half PWM header. This allows compilation for the lower-level PWM drivers even if the upper-half PWM logic is not used.
arch/arm/src/stm32/stm32_tim.c: fix compilation error if there is no TIM8
configs/nucleo-f334r8/highpri: remove the upper-half ADC from configuration
configs/nucleo-f302r8/highpri: remove the upper-half ADC from configuration
configs/stm32f429i-disco/highpri: remove the upper-half ADC from configuration
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva: Add CC13xx GPIO driver plus various fixes for clean compilation.
arch/arm/src/tiva/ and configs/launchxl-cc1312r1: Make type of the GPIO pin configuration an abstract type so that CC13xx MCUs can share the same GPIO function prototypes and usage model.
Improvements in STM32 ADC
arch/arm/src/stm32/stm32_adc.c: start conversion on startup is now possible if TIM triggering selected. This can be useful to start ADC TIM conversion for ADC IPv2 when opening ADC device.
arch/arm/src/stm32/stm32_adc.c: fix compilation errors for chips with one ADV TIM
configs/nucleo-f303re: refresh ADC example
configs/nucleo-f334r8: refresh ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
Use STM32 DMA IP core version instead of chip family names and some minor improvements
arch/arm/src/stm32/chip/stm32_adc.h: raise error if two IP cores seleceted
libs/libdsp/Kconfig: cosmetic change
arch/arm/src/stm32/Kconfig: hide TIMER menu, HRTIM menu and USB Host debug menu if peripherals not enabled
configs/stm32f429i-disco/highpri/defconfig: fix configuration warning
Approved-by: GregoryN <gnutt@nuttx.org>
configs/nucleo-f207zg, configs/nucleo-f103rb: add ADC and PWM examples; arch/arm/src/stm32_adc.c: there is no DMA CFG bit for the basic IPv1 ADC
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/tiva/Make.defs: Trivial change to conditional VPATH.
arch/arm/src/tiva: Move LM3S and LM4F source files to lm/ sub-directory. Move all TM4C source files to tm4c sub-directory.
arch/arm/src/tiva and configs/: Change include patch from chip/ to hardware/ in all Tiva files includes.
arch/tmp/src: Rename chip/ subdirectory to hardware/. This is a better name since it does not conflict with other directory names and, well, we are going to be change a lot of the Tiva directory structure in the next few commits.
arch/arm/src/max326xx/max32660/max32660_spim.c: SPI0 master mode support is complete (sans DMA and completely untested). configs/max32660-evsys/src: Add framework for SPI support.
arch/arm/src/max326xx/max32660/max32660_spim.c: Fleshes out some of the data transfer logic. More needs to be done. Also removes leveraged DMA support. It will be a long time (if ever) before DMA is supported. No point in dragging all of that bogus logic around.
Squashed commit of the following:
arch/arm/src/max326xx/max32660/max32660_spim.c: A few updates tot he SPI master driver. Still incomplete and does not even compile.
Update some comments
arch/arm/src/max326xx: Clean up some general build issues. Still STM32 code posing as MAX32660.
arch/arm/src/max326xx: Starting SPI driver. Initial commit is just the STM32 SPI driver with name changes.
arch/arm/src/max326xx and configs/max32660-evsys/src: Fix some issues with GPIO setup of output pins. Correct polarity of on-board LED output. The on-board LED is now functional.
arch/arm/src/max326xx: WFI instruction in IDLE loop seems to interfere with stability. Commented out for now. Needs to be investigated further.
arch/arm/src/max326xx: Fixes for GPIO configuration problems and serial driver problems. I now get the NuttShell prompt (if I also band on ENTER to force all of the characters out). Progress, but not yet ready.
configs/max32660-evsys: Support CONFIG_BOOT_RUNFROMISRAM=y.
arch/arm/src/max326xx/max32660/max32660_clockconfig.c: Fix an error in a register name.
arm/src/max326xx/max32660: Fix a few new compilation errors when DEBUG is enabled.
Improvements in STM32 ADC, minor changes in STM32 PWM, DMA, HRTIM and add some highpri ADC examples
arch/arch/src/stm32/stm32_adc: fix RCC reset logic
arch/arch/src/stm32/stm32_adc: move sample time change functions to low-level ADC ops
arch/arch/src/stm32/stm32_adc: configurable ADC DMA mode (one shot mode, circular mode)
arch/arch/src/stm32/stm32_pwm: remove llops_get interface. We can use structure casting to get pwm low-level ops
arch/arch/src/stm32/stm32_pwm: add timer enable/disable and frequency update to low-level ops
arch/src/arm/stm32: remove redundant stm32f33xxx_dma.c
arch/arm/src/stm32/stm32f40xxx_dma.c: add interfaces to interact with highp priority DMA interupts
arch/src/arm/stm32/stm32_hrtim: do not enable timers on startup if option from Kconfig selected and add interface to enable/disable timers
arch/src/arm/stm32/stm32_hrtim: fix some warnings
configs/nucleo-f334r8/highpri: update configuration due to changes in stm32_adc
configs/stm32f334-disco/buckboost: update configuration due to changes in stm32_adc
configs/nucleo-f334r8/highpri: add support for ADC injected sequence, add triggering from TIM1
configs/nucleo-f302r8/highpri: add high priority ADC interrupts example
configs/stm32f429i-disco/highpri: add high priority ADC interrupts example
Approved-by: GregoryN <gnutt@nuttx.org>
configs/stm32vldiscovery: Fix memory size configuration and documentation
There is STM32F100RB instead of STM32F100RC on the STM32 VL Discovery kit.
Approved-by: GregoryN <gnutt@nuttx.org>
configs/stm32vldiscovery/scripts/stm32vldiscovery.ld: Fix SRAM and FLASH size in the linker script.
There is STM32F100RB with 8KB RAM and 128KB FLASH on the STM32VL Discovery kit. Invalid memory size could cause a hard fault.
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/max326xx/max32660/max32660_serial.c: Add a mostly commented out serial driver. With this, we can accomplish a complete build with many warnings for 'Missing logic'
configs/max32660-evsys/src/max326_button.c: Add support for the on-board button.
arch/arm/src/max326xx: Add a mostly empty max326_lowputc.c file mostly so that we can get further in the compilation. Fixed several more compile errors revealed by this.
arch/arm/src/max326xx: Add peripheral clock control header file.
Author: Gregory Nutt <gnutt@nuttx.org>
A few trivial updates from review of changes.
Remove references to NRF52-PCA10040 from documentation. Replace with NRF52-generic.
Remove configs/nrf52-pca10040/ Replaced with configs/nrf52-generic.
Author: Zou Hanya <hanyazou@gmail.com>
Improve LED handling #if~#endif in nrf52_autoleds.c and nrf52_userleds.c
Add Adafruit Feather nRF52 board LED support
Add Adafruit Feather nRF52 board
Add nrf52-generic
Replace 'pca10040' with 'generic'
Copy from nrf52-pca10040 to nrf52-generic
Squashed commit of the following:
arch/arm/src/max326xx and configs/max32660-evsys/nsh/defconfig: Work out some issues related to MAX326xx configuration.
configs/max32660-evsys: Add unverified board support framework.
