2015-03-09 15:23:09 +01:00
README
======
This README file discusses the port of NuttX to the Atmel SAM V71 Xplained
Ultra Evaluation Kit (SAMV71-XULT). This board features the ATSAMV71Q21 Cortex-M7
microcontroller.
2015-03-30 23:31:53 +02:00
Additional support of provided for the (optional) maXTouch Xplained Pro LCD.
2015-03-09 15:23:09 +01:00
Contents
========
- Board Features
2015-05-12 21:36:23 +02:00
- Status/Open Issues
2015-03-09 15:23:09 +01:00
- Serial Console
2015-03-13 16:27:16 +01:00
- SD card
- Automounter
2015-03-09 15:23:09 +01:00
- LEDs and Buttons
2015-03-12 19:27:06 +01:00
- AT24MAC402 Serial EEPROM
2015-11-07 18:25:58 +01:00
- S25FL116K QuadSPI FLASH
2015-11-13 22:13:55 +01:00
- Program FLASH Access
2015-03-16 20:51:37 +01:00
- Networking
2015-08-16 18:59:35 +02:00
- USBHS Device Controller Driver
2015-04-01 20:13:51 +02:00
- Audio Interface
2015-03-30 23:31:53 +02:00
- maXTouch Xplained Pro
2015-08-05 16:05:26 +02:00
- MCAN1 Loopback Test
2015-08-11 17:30:52 +02:00
- SPI Slave
2017-07-02 19:04:57 +02:00
- Click Shield
2015-12-02 15:37:42 +01:00
- Tickless OS
2015-03-10 23:11:28 +01:00
- Debugging
2015-03-09 15:23:09 +01:00
- Configurations
Board Features
==============
- ATSAMV71Q21 microcontroller: Cortex-M7, 300MHz, 2MiB FLASH, 384KiB SRAM,
I/D-caches
- One mechanical reset button
- One power switch button
- Two mechanical user pushbuttons
- Two yellow user LEDs
- Supercap backup
- 12.0 MHz crystal
- 32.768 kHz crystal
- 2 MB SDRAM
- 2 MB QSPI Flash
- IEEE 802.3az 10Base-T/100Base-TX Ethernet RMII PHY
- AT24MAC402 256KByte EEPROM with EUI-48 address
- WM8904 stereo audio codec
- ATA6561 CAN Transceiver
- SD Card connector with SDIO support
- Camera interface connector
- MediaLB connector
- Two Xplained Pro extension headers
- One Xplained Pro LCD header
- Coresight 20 connector for 4-bit ETM
- Arduino due compatible shield connectors
- External debugger connector
- USB interface, device and host mode
- Embedded Debugger with Data Gateway Interface and Virtual COM port (CDC)
- External power input (5-14V) or USB powered
2015-03-28 16:42:45 +01:00
See the Atmel website for further information about this board:
2015-03-09 15:23:09 +01:00
- http://www.atmel.com/tools/atsamv71-xult.aspx
2015-08-11 15:52:20 +02:00
Status/Open Issues
==================
2015-03-15 17:22:14 +01:00
2015-05-12 21:43:04 +02:00
I would characterize the general port as very mature and stable. However,
2015-05-12 21:36:23 +02:00
there are a number of issues, caveats, and unfinished drivers as detailed in
the following paragraphs.
The BASIC nsh configuration is fully function (as described below under
2015-05-13 18:38:54 +02:00
"Configurations"). There is also a graphics configuration (mxtxplnd), a
2015-11-18 18:45:01 +01:00
a configuration for network testing (netnsh), a graphics demo (nxwm), and
a sample protected mode build (knsh). There are still open issues that need
to be resolved. General problems are listed below. But see the STATUS
section associated with each configuration for additional issues specific
to a particular configuration.
2015-03-15 17:22:14 +01:00
2015-04-05 03:58:31 +02:00
1. HSCMI. CONFIG_MMCSD_MULTIBLOCK_DISABLE=y is set to disable multi-block
2015-03-15 17:22:14 +01:00
transfers only because I have not yet had a chance to verify this. The
is very low priority to me but might be important to you if you are need
very high performance SD card accesses.
2015-04-05 03:58:31 +02:00
2. HSMCI TX DMA is currently disabled for the SAMV7. There is some
2015-12-02 15:37:42 +01:00
issue with the TX DMA setup. This is a bug that needs to be resolved.
2015-03-15 17:22:14 +01:00
2015-12-02 15:37:42 +01:00
DMA is enabled by these settings in the file arch/arm/src/samv7/sam_hsmci.c:
2015-03-15 19:17:39 +01:00
#undef HSCMI_NORXDMA /* Define to disable RX DMA */
#define HSCMI_NOTXDMA 1 /* Define to disable TX DMA */
2015-04-05 03:58:31 +02:00
3. There may also be some issues with removing and re-inserting SD cards
2015-03-15 22:06:17 +01:00
(of course with appropriate mounting and unmounting). I all not sure
of this and need to do more testing to characterize if the issue.
2015-04-05 03:58:31 +02:00
4. There is a port of the SAMA5D4-EK Ethernet driver to the SAMV71-XULT.
2015-03-29 22:42:03 +02:00
This driver appears to be 100% functional with the following caveats:
2015-03-28 21:54:30 +01:00
2015-03-30 15:33:48 +02:00
- There is a compiler optimization issue. At -O2, there is odd
2015-03-28 21:54:30 +01:00
behavior on pings and ARP messages. But the behavior is OK with
2015-03-29 22:42:03 +02:00
optimization set to -O2. This may or may not be a compiler
optimization issue (it could also be a timing issue or a need
for some additional volatile qualifiers).
2015-11-07 18:25:58 +01:00
Update: I have switch toolchains and no longer see this issue. This
is probably not a driver-related issue.
2015-03-29 22:42:03 +02:00
- I- and D-Caches are enabled but the D-Cache must be enabled in
2015-03-30 15:33:48 +02:00
write-through mode. This is to work around issues with the RX and TX
2015-03-29 22:42:03 +02:00
descriptors with are 8-bytes in size. But the D-Cache cache line size
is 32-bytes. That means that you cannot reload, clean or invalidate a
descriptor without also effecting three neighboring descriptors.
Setting write through mode eliminates the need for cleaning the D-Cache.
If only reloading and invalidating are done, then there is no problem.
2015-03-29 21:09:22 +02:00
2015-08-21 20:32:34 +02:00
5. The USBHS device controller driver (DCD) is also fully functional. It
has only be tested with the CDC/ACM driver as described below. Like
the Ethernet driver:
2015-03-16 20:51:37 +01:00
2015-08-21 20:32:34 +02:00
- This driver does not work reliably with the write back D-Cache. The
write-through D-Cache must be enabled.
2015-08-22 18:14:36 +02:00
- As of this writing (2015-08-22), the USBHS only works in full speed
mode (aka, USBHS Low-Power mode). When configured in normal mode,
SETUP packets are no longer received or responded to; the firmware
only detects bus reset events. This is probably some issue with
480MHZ high speed clock setup, but I have not yet found the issue.
2015-05-13 01:59:45 +02:00
6. The full port for audio support is code complete: WM8904 driver,
2015-04-10 19:33:01 +02:00
SSC/I2C driver, and CS2100-CP driver. But this code is untested. The
WM8904 interface was taken directly from the SAMA5D4-EK and may well
need modification due to differences with the physical WM8904
interface.
2015-08-11 15:52:20 +02:00
7. An MCAN driver as added and verified on 2015-08-08 using the loopback
test at apps/examples/can. Like the Ethernet driver, the MCAN driver
does not work if the D-Cache is configured in write-back mode; write-
through mode is required.
2015-08-11 17:30:52 +02:00
8. An SPI slave driver as added on 2015-08-09 but has not been verified
as of this writing. See discussion in include/nuttx/spi/slave.h and
in the section entitle "SPI Slave" below.
2015-08-11 15:52:20 +02:00
2015-11-11 01:08:21 +01:00
9. A QSPI FLASH driver was added and verifed on 2015-11-10. This driver
2015-11-07 18:25:58 +01:00
operated in the memory mapped Serial Memory Mode (SMM). See the
"S25FL116K QuadSPI FLASH" section below for futher information.
2015-11-13 22:13:55 +01:00
10. On-chip FLASH support as added and verified on 2015-11-13. See the
"Program FLASH Access" section below for further information.
2015-11-18 18:45:01 +01:00
11. The knsh "protected mode" configuration was added on 2015-11-18. The
configuration has not been tested as of this writing.
2015-03-30 23:31:53 +02:00
Serial Console
2015-03-09 15:23:09 +01:00
==============
The SAMV71-XULT has no on-board RS-232 drivers so it will be necessary to
use either the VCOM or an external RS-232 driver. Here are some options.
- Arduino Serial Shield: One option is to use an Arduino-compatible
serial shield. This will use the RXD and TXD signals available at pins
0 an 1, respectively, of the Arduino "Digital Low" connector. On the
SAMV71-XULT board, this corresponds to UART3:
------ ------ ------- ------- --------
Pin on SAMV71 Arduino Arduino SAMV71
J503 PIO Name Pin Function
------ ------ ------- ------- --------
1 PD28 RX0 0 URXD3
2 PD30 TX0 1 UTXD3
------ ------ ------- ------- --------
2015-03-26 19:33:03 +01:00
In this configuration, an external RS232 driver can also be used
instead of the shield. Simply connext as follows:
--------- -----------
Arduino RS-232
Pin Label Connection
--------- -----------
D0 (RXD) RX
D1 (TXD) TX
GND GND
5VO Vcc
--------- -----------
2015-04-04 16:43:41 +02:00
- Arduino Communications. Additional UART/USART connections are available
on the Arduino Communications connection J505:
------ ------ ------- ------- --------
Pin on SAMV71 Arduino Arduino SAMV71
J503 PIO Name Pin Function
------ ------ ------- ------- --------
3 PD18 RX1 0 URXD4
4 PD19 TX1 0 UTXD4
5 PD15 RX2 0 RXD2
6 PD16 TX2 0 TXD2
7 PB0 RX3 0 RXD0
8 PB1 TX3 1 TXD0
------ ------ ------- ------- --------
2015-03-09 15:23:09 +01:00
- SAMV7-XULT EXTn connectors. USART pins are also available the EXTn
connectors. The following are labelled in the User Guide for USART
functionality:
---- -------- ------ --------
EXT1 EXTI1 SAMV71 SAMV71
Pin Name PIO Function
---- -------- ------ --------
13 USART_RX PB00 RXD0
14 USART_TX PB01 TXD0
---- -------- ------ --------
EXT2 EXTI2 SAMV71 SAMV71
Pin Name PIO Function
---- -------- ------ --------
13 USART_RX PA21 RXD1
14 USART_TX PB04 TXD1
- VCOM. The Virtual Com Port gateway is available on USART1:
------ --------
SAMV71 SAMV71
PIO Function
------ --------
PB04 TXD1
PA21 RXD1
------ --------
Any of these options can be selected as the serial console by:
1. Enabling the UART/USART peripheral in the
"System Type -> Peripheral Selection" menu, then
2. Configuring the peripheral in the "Drivers -> Serial Configuration"
menu.
2015-12-01 00:37:01 +01:00
NOTE: If USART1 is used (TXD1, RXD1), then PB4 must be reconfigured in the
SUPC. Normally, PB4 is TDI. When it is reconfigured for use with USART1,
the capability to debug is lost! If you plan to debug you should most
2015-12-05 23:13:29 +01:00
certainly not use USART1.
2015-12-01 00:37:01 +01:00
2015-03-13 16:27:16 +01:00
SD Card
=======
Card Slot
---------
The SAM V71 Xplained Ultra has one standard SD card connector which is
connected to the High Speed Multimedia Card Interface (HSMCI) of the SAM
V71. SD card connector:
------ ----------------- ---------------------
SAMV71 SAMV71 Shared functionality
Pin Function
------ ----------------- ---------------------
PA30 MCDA0 (DAT0)
PA31 MCDA1 (DAT1)
PA26 MCDA2 (DAT2)
PA27 MCDA3 (DAT3) Camera
PA25 MCCK (CLK) Shield
PA28 MCCDA (CMD)
PD18 Card Detect (C/D) Shield
------ ----------------- ---------------------
Configuration Settings
----------------------
Enabling HSMCI support. The SAMV7-XULT provides a one, full-size SD memory card slots. The full size SD card slot connects via HSMCI0. Support for the SD slots can be enabled with the following settings:
System Type->SAMV7 Peripheral Selection
CONFIG_SAMV7_HSMCI0=y : To enable HSMCI0 support
CONFIG_SAMV7_XDMAC=y : XDMAC is needed by HSMCI0/1
System Type
2015-09-25 18:14:40 +02:00
CONFIG_SAMV7_GPIO_IRQ=y : PIO interrupts needed
CONFIG_SAMV7_GPIOD_IRQ=y : Card detect pin is on PD18
2015-03-13 16:27:16 +01:00
Device Drivers -> MMC/SD Driver Support
CONFIG_MMCSD=y : Enable MMC/SD support
CONFIG_MMSCD_NSLOTS=1 : One slot per driver instance
CONFIG_MMCSD_MULTIBLOCK_DISABLE=y : (REVISIT)
CONFIG_MMCSD_HAVECARDDETECT=y : Supports card-detect PIOs
CONFIG_MMCSD_MMCSUPPORT=n : Interferes with some SD cards
CONFIG_MMCSD_SPI=n : No SPI-based MMC/SD support
CONFIG_MMCSD_SDIO=y : SDIO-based MMC/SD support
CONFIG_SDIO_DMA=y : Use SDIO DMA
CONFIG_SDIO_BLOCKSETUP=y : Needs to know block sizes
RTOS Features -> Work Queue Support
CONFIG_SCHED_WORKQUEUE=y : Driver needs work queue support
Application Configuration -> NSH Library
CONFIG_NSH_ARCHINIT=y : NSH board-initialization, OR
CONFIG_BOARD_INITIALIZE=y
Using the SD card
-----------------
1) After booting, the HSCMI device will appear as /dev/mmcsd0.
2) If you try mounting an SD card with nothing in the slot, the mount will
fail:
nsh> mount -t vfat /dev/mmcsd0 /mnt/sd0
nsh: mount: mount failed: 19
NSH can be configured to provide errors as strings instead of
numbers. But in this case, only the error number is reported. The
error numbers can be found in nuttx/include/errno.h:
#define ENODEV 19
#define ENODEV_STR "No such device"
So the mount command is saying that there is no device or, more
correctly, that there is no card in the SD card slot.
3) Inserted the SD card. Then the mount should succeed.
nsh> mount -t vfat /dev/mmcsd0 /mnt/sd0
nsh> ls /mnt/sd1
/mnt/sd1:
atest.txt
nsh> cat /mnt/sd1/atest.txt
This is a test
NOTE: See the next section entitled "Auto-Mounter" for another way
to mount your SD card.
4) Before removing the card, you must umount the file system. This is
equivalent to "ejecting" or "safely removing" the card on Windows: It
flushes any cached data to an SD card and makes the SD card unavailable
to the applications.
nsh> umount -t /mnt/sd0
It is now safe to remove the card. NuttX provides into callbacks
that can be used by an application to automatically unmount the
volume when it is removed. But those callbacks are not used in
these configurations.
Auto-Mounter
============
NuttX implements an auto-mounter than can make working with SD cards
easier. With the auto-mounter, the file system will be automatically
mounted when the SD card is inserted into the HSMCI slot and automatically
unmounted when the SD card is removed.
Here is a sample configuration for the auto-mounter:
File System Configuration
CONFIG_FS_AUTOMOUNTER=y
Board-Specific Options
2015-03-30 23:31:53 +02:00
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT=y
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT_FSTYPE="vfat"
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT_BLKDEV="/dev/mmcsd0"
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT_MOUNTPOINT="/mnt/sdcard"
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT_DDELAY=1000
CONFIG_SAMV71XULT_HSMCI0_AUTOMOUNT_UDELAY=2000
2015-03-13 16:27:16 +01:00
WARNING: SD cards should never be removed without first unmounting
them. This is to avoid data and possible corruption of the file
system. Certainly this is the case if you are writing to the SD card
at the time of the removal. If you use the SD card for read-only access,
however, then I cannot think of any reason why removing the card without
mounting would be harmful.
2015-03-09 15:23:09 +01:00
LEDs and Buttons
================
LEDs
----
There are two yellow LED available on the SAM V71 Xplained Ultra board that
can be turned on and off. The LEDs can be activated by driving the
connected I/O line to GND.
------ ----------- ---------------------
SAMV71 Function Shared functionality
PIO
------ ----------- ---------------------
PA23 Yellow LED0 EDBG GPIO
PC09 Yellow LED1 LCD, and Shield
------ ----------- ---------------------
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/sam_autoleds.c. The LEDs are used to encode
OS-related events as follows:
------------------- ----------------------- -------- --------
SYMBOL Meaning LED state
LED0 LED1
------------------- ----------------------- -------- --------
LED_STARTED NuttX has been started OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF OFF
LED_IRQSENABLED Interrupts enabled OFF OFF
LED_STACKCREATED Idle stack created ON OFF
LED_INIRQ In an interrupt No change
LED_SIGNAL In a signal handler No change
LED_ASSERTION An assertion failed No change
LED_PANIC The system has crashed N/C Blinking
LED_IDLE MCU is is sleep mode Not used
------------------- ----------------------- -------- --------
Thus if LED0 is statically on, NuttX has successfully booted and is,
apparently, running normally. If LED1 is flashing at approximately
2Hz, then a fatal error has been detected and the system has halted.
NOTE: That LED0 is not used after completion of booting and may
be used by other board-specific logic.
Buttons
-------
SAM V71 Xplained Ultra contains three mechanical buttons. One button is the
RESET button connected to the SAM V71 reset line and the others are generic
user configurable buttons. When a button is pressed it will drive the I/O
line to GND.
------ ----------- ---------------------
SAMV71 Function Shared functionality
PIO
------ ----------- ---------------------
RESET RESET Trace, Shield, and EDBG
PA09 SW0 EDBG GPIO and Camera
PB12 SW1 EDBG SWD and Chip Erase
------ ----------- ---------------------
NOTES:
- There are no pull-up resistors connected to the generic user buttons so
it is necessary to enable the internal pull-up in the SAM V71 to use the
button.
- PB12 is set up as a system flash ERASE pin when the firmware boots. To
use the SW1, PB12 has to be configured as a normal regular I/O pin in
the MATRIX module. For more information see the SAM V71 datasheet.
2015-03-12 19:27:06 +01:00
AT24MAC402 Serial EEPROM
========================
2015-03-19 21:53:05 +01:00
Ethernet MAC Address
--------------------
2015-03-12 19:27:06 +01:00
The SAM V71 Xplained Ultra features one external AT24MAC402 serial EEPROM
with a EIA-48 MAC address connected to the SAM V71 through I2C. This device
contains a MAC address for use with the Ethernet interface.
Connectivity:
------ -------- -------- ------------------------------------------
SAMV71 SAMV71 I2C Shared
Pin Function Function Functionality
------ -------- -------- ------------------------------------------
PA03 TWID0 SDA EXT1, EXT2, EDBG I2C, LCD, Camera, Audio,
MediaLB, and Shield
PA04 TWICK0 SCL EXT1, EXT2, EDBG I2C, LCD, Camera, Audio,
MediaLB, and Shield
------ -------- -------- ------------------------------------------
I2C address:
2015-03-18 00:10:44 +01:00
The 7-bit addresses of the AT24 part are 0b1010AAA for the normal 2Kbit
memory and 0b1011aaa for the "extended memory" where aaa is the state of
the A0, A1, and A3 pins on the part. On the SAMV71-XULT board, these
2015-03-12 19:27:06 +01:00
are all pulled high so the full, 7-bit address is 0x5f.
2015-03-19 21:53:05 +01:00
Configuration
-------------
System Type -> SAMV7 Peripheral Support
CONFIG_SAMV7_TWIHS0=y : Used to access the EEPROM
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
Device drivers -> Memory Technology Devices
CONFIG_MTD_AT24XX=y : Enable the AT24 device driver
CONFIG_AT24XX_SIZE=2 : Normal EEPROM is 2Kbit (256b)
CONFIG_AT24XX_ADDR=0x57 : Normal EEPROM address */
CONFIG_AT24XX_EXTENDED=y : Supports an extended memory region
CONFIG_AT24XX_EXTSIZE=160 : Extended address up to 0x9f
MTD Configuration Data
----------------------
The AT24 EEPROM can also be used to storage of up to 256 bytes of
configuration data:
Device drivers -> Memory Technology Devices
The configuration data device will appear at /dev/config.
2015-11-07 18:25:58 +01:00
S25FL116K QuadSPI FLASH
====================
A QSPI FLASH driver was added and verifed on 2015-11-07. This driver
operated in the memory mapped Serial Memory Mode (SMM). These
configuration options were enabled to test QSPI:
CONFIG_SAMV7_QSPI=y
CONFIG_SAMV7_QSPI_DLYBCT=0
CONFIG_SAMV7_QSPI_DLYBS=0
CONFIG_SAMV7_QSPI_DMA=y
CONFIG_SAMV7_QSPI_DMATHRESHOLD=8
The MPU must be enabled to use QSPI:
CONFIG_ARCH_USE_MPU=y
2015-12-14 20:56:56 +01:00
CONFIG_ARM_MPU=y
CONFIG_ARM_MPU_NREGIONS=16
2015-11-07 18:25:58 +01:00
And there options enable the driver for the on-board S25FL116K QuadSPI
FLASH:
CONFIG_MTD_S25FL1=y
CONFIG_S25FL1_QSPIMODE=0
CONFIG_S25FL1_QSPI_FREQUENCY=108000000
2015-11-11 00:41:53 +01:00
SmartFS
-------
2015-11-11 21:28:01 +01:00
The SmartFS file system is selected with the following settings.
2015-11-07 18:25:58 +01:00
CONFIG_FS_SMARTFS=y
CONFIG_SMARTFS_ERASEDSTATE=0xff
CONFIG_SMARTFS_MAXNAMLEN=16
CONFIG_MTD_SMART=y
CONFIG_MTD_SMART_SECTOR_SIZE=512
CONFIG_MTD_SMART_WEAR_LEVEL=y
Upon boot, the on-board S25FL116k flash device will appears as:
/dev/smart0
2015-11-11 21:28:01 +01:00
Before SmartFS can be used, it must be formatted. So this command
must be used one time the first time that the system boots:
2015-11-07 18:25:58 +01:00
nsh> mksmartfs /dev/smart0
Then it can be mounted using the following NSH command:
nsh> mount -t smartfs /dev/smart0 /mnt/qspi
The first time that you boot the system, there will be a long delay
before the nsh> prompt. That long delay is SmartFS scanning the
large FLASH part. Likewise, the when you format the SmartFS, you
also expect a significant delay.
A better application design would perform SmartFS initialization
asynchronously on a separate thread to avoid the delay at the user
interface.
2015-11-11 00:41:53 +01:00
NXFFS
-----
The NXFFS file system is selected with the following settings.
CONFIG_FS_NXFFS=y
CONFIG_NXFFS_ERASEDSTATE=0xff
CONFIG_NXFFS_MAXNAMLEN=255
CONFIG_NXFFS_PACKTHRESHOLD=32
CONFIG_NXFFS_PREALLOCATED=y
CONFIG_NXFFS_TAILTHRESHOLD=8192
The NXFFS file system is automatically mounted by logic src/sam_bringup.c when the system boots:
nsh> mount
/mnt/s25fl1 type nxffs
nsh> echo "This is a test" >/mnt/s25fl1/atest.txt
nsh> ls /mnt/s25fl1
/mnt/s25fl1:
atest.txt
nsh> cat /mnt/s25fl1/atest.txt
This is a test
Character Driver
----------------
If neither SmartFS nor NXFFS are defined, then the S25FL1 driver will be
wrapped as a character driver and available as /dev/mtd0.
2015-11-13 22:13:55 +01:00
Program FLASH Access
====================
An on-chip FLASH driver was added and verifed on 2015-11-13. These
configuration options were enabled to test the on-chip FLASH support:
CONFIG_MTD_PROGMEM=y
CONFIG_SAMV7_PROGMEM=y
CONFIG_SAMV7_PROGMEM_NSECTORS=8
D-Cache must be configured in write-through mode:
CONFIG_ARMV7M_DCACHE_WRITETHROUGH=y
2015-11-13 22:56:16 +01:00
The total FLASH on the SAMV71 is organized as 128KB/sector x 16 sectors
= 2MB. The sectors are all uniform (except for sector zero which will
never be used by the driver).
2015-11-13 22:13:55 +01:00
2015-11-13 22:56:16 +01:00
The configuration sets aside 8 sectors, or 8 * 128KB = 1MB of the FLASH
for programmable memory (CONFIG_SAMV7_PROGMEM_NSECTORS=8). The exact
number of sectors set aside is optional.
NOTE: Ideally, one should also modify the linker script and reduce the size
of the available FLASH the amount set aside for program usage to avoid
difficult run-time problems. That would be 1MB in this configuration. I
did not do that only because I know that my test program is small.
2015-11-13 22:13:55 +01:00
When the system boots, you can see the FLASH driver:
NuttShell (NSH) NuttX-7.12
nsh> ls /dev
/dev:
config
console
mmcsd0
mtd1
mtdblock1
null
ttyS0
/dev/mtdblock1 is a block driver that can be used with any file system on
the FLASH; /dev/mtd1 is the corresponding character driver used by the
apps/examples/media test.
Each of the uniform sectors is divided up into 256 512B "pages". This is
not really useful, however, because we can only erase a minimum of groups
of 16 pages or 8KB. In the code, I you will see that I refer to these
groups of 16 pages as "clusters." So the cluster is the smallest thing
that you can perform a read/write/modify operation on.
2015-11-13 22:56:16 +01:00
Using 8 sectors yields 16 *8 = 128 clusters (aka blocks). You can see
2015-11-13 22:13:55 +01:00
this when the apps/examples/media test runs:
nsh> media
MTD Geometry:
blocksize: 8192
erasesize: 8192
neraseblocks: 128
Using:
blocksize: 8192
nblocks: 128
Write/Verify: Block 0
Write/Verify: Block 1
Write/Verify: Block 2
Write/Verify: Block 3
...
Write/Verify: Block 127
Re-read/Verify: Block 0
Re-read/Verify: Block 1
Re-read/Verify: Block 2
Re-read/Verify: Block 3
...
Re-read/Verify: Block 127
nsh>
2015-11-13 22:56:16 +01:00
NOTE: The media test can be added to the NSH configuration with:
CONFIG_EXAMPLES_MEDIA=y
CONFIG_EXAMPLES_MEDIA_BLOCKSIZE=8192
CONFIG_EXAMPLES_MEDIA_DEVPATH="/dev/mtd1"
2015-03-16 20:51:37 +01:00
Networking
==========
KSZ8061RNBVA Connections
------------------------
------ --------- --------- --------------------------
SAMV71 SAMV71 Ethernet Shared functionality
Pin Function Function
------ --------- --------- --------------------------
PD00 GTXCK REF_CLK Shield
PD01 GTXEN TXEN
PD02 GTX0 TXD0
PD03 GTX1 TXD1
PD04 GRXDV CRS_DV Trace
PD05 GRX0 RXD0 Trace
PD06 GRX1 RXD1 Trace
PD07 GRXER RXER Trace
PD08 GMDC MDC Trace
PD09 GMDIO MDIO
PA19 GPIO INTERRUPT EXT1, Shield
PA29 GPIO SIGDET
PC10 GPIO RESET
------ --------- --------- --------------------------
Selecting the GMAC peripheral
-----------------------------
System Type -> SAMV7 Peripheral Support
CONFIG_SAMV7_EMAC0=y : Enable the GMAC peripheral (aka, EMAC0)
2015-03-17 21:29:41 +01:00
CONFIG_SAMV7_TWIHS0=y : We will get the MAC address from the AT24 EEPROM
2015-03-19 21:53:05 +01:00
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
2015-03-16 20:51:37 +01:00
System Type -> EMAC device driver options
CONFIG_SAMV7_EMAC0_NRXBUFFERS=16 : Set aside some RS and TX buffers
CONFIG_SAMV7_EMAC0_NTXBUFFERS=8
CONFIG_SAMV7_EMAC0_RMII=y : The RMII interfaces is used on the board
CONFIG_SAMV7_EMAC0_AUTONEG=y : Use autonegotiation
CONFIG_SAMV7_EMAC0_PHYADDR=1 : KSZ8061 PHY is at address 1
CONFIG_SAMV7_EMAC0_PHYSR=30 : Address of PHY status register on KSZ8061
CONFIG_SAMV7_EMAC0_PHYSR_ALTCONFIG=y : Needed for KSZ8061
CONFIG_SAMV7_EMAC0_PHYSR_ALTMODE=0x7 : " " " " " "
CONFIG_SAMV7_EMAC0_PHYSR_10HD=0x1 : " " " " " "
CONFIG_SAMV7_EMAC0_PHYSR_100HD=0x2 : " " " " " "
CONFIG_SAMV7_EMAC0_PHYSR_10FD=0x5 : " " " " " "
CONFIG_SAMV7_EMAC0_PHYSR_100FD=0x6 : " " " " " "
PHY selection. Later in the configuration steps, you will need to select
the KSZ8061 PHY for EMAC (See below)
Networking Support
CONFIG_NET=y : Enable Neworking
CONFIG_NET_SOCKOPTS=y : Enable socket operations
CONFIG_NET_ETH_MTU=562 : Maximum packet size (MTU) 1518 is more standard
CONFIG_NET_ETH_TCP_RECVWNDO=562 : Should be the same as CONFIG_NET_ETH_MTU
CONFIG_NET_ARP=y : ARP support should be enabled
CONFIG_NET_ARP_SEND=y : Use ARP to get peer address before sending
CONFIG_NET_TCP=y : Enable TCP/IP networking
CONFIG_NET_TCPBACKLOG=y : Support TCP/IP backlog
CONFIG_NET_TCP_READAHEAD=y : Enable TCP read-ahead buffering
CONFIG_NET_TCP_WRITE_BUFFERS=y : Enable TCP write buffering
CONFIG_NET_UDP=y : Enable UDP networking
CONFIG_NET_BROADCAST=y : Support UDP broadcase packets
CONFIG_NET_ICMP=y : Enable ICMP networking
CONFIG_NET_ICMP_PING=y : Needed for NSH ping command
: Defaults should be okay for other options
Device drivers -> Network Device/PHY Support
CONFIG_NETDEVICES=y : Enabled PHY selection
CONFIG_ETH0_PHY_KSZ8061=y : Select the KSZ8061 PHY used with EMAC0
2015-03-17 21:29:41 +01:00
Device drivers -> Memory Technology Devices
CONFIG_MTD_AT24XX=y : Enable the AT24 device driver
CONFIG_AT24XX_SIZE=2 : Normal EEPROM is 2Kbit (256b)
CONFIG_AT24XX_ADDR=0x57 : Normal EEPROM address */
CONFIG_AT24XX_EXTENDED=y : Supports an extended memory region
CONFIG_AT24XX_EXTSIZE=160 : Extended address up to 0x9f
2015-03-27 20:04:43 +01:00
RTOS Features ->Work Queue Support
CONFIG_SCHED_WORKQUEUE=y : Work queue support is needed
CONFIG_SCHED_HPWORK=y
CONFIG_SCHED_HPWORKSTACKSIZE=2048 : Might need to be increased
2015-03-16 20:51:37 +01:00
Application Configuration -> Network Utilities
2015-07-10 20:09:58 +02:00
CONFIG_NETDB_DNSCLIENT=y : Enable host address resolution
2015-03-16 20:51:37 +01:00
CONFIG_NETUTILS_TELNETD=y : Enable the Telnet daemon
CONFIG_NETUTILS_TFTPC=y : Enable TFTP data file transfers for get and put commands
CONFIG_NETUTILS_NETLIB=y : Network library support is needed
CONFIG_NETUTILS_WEBCLIENT=y : Needed for wget support
: Defaults should be okay for other options
Application Configuration -> NSH Library
CONFIG_NSH_TELNET=y : Enable NSH session via Telnet
CONFIG_NSH_IPADDR=0x0a000002 : Select an IP address
CONFIG_NSH_DRIPADDR=0x0a000001 : IP address of gateway/host PC
CONFIG_NSH_NETMASK=0xffffff00 : Netmask
2015-03-17 21:29:41 +01:00
CONFIG_NSH_NOMAC=n : We will get the IP address from EEPROM
2015-03-16 20:51:37 +01:00
: Defaults should be okay for other options
2017-03-30 16:43:07 +02:00
SAMV71 Versions
---------------
2017-03-30 20:29:19 +02:00
WARNING: The newer SAMV71 have 6 GMAC queues, not 3. All queues must be
2017-03-30 16:43:07 +02:00
configured for the GMAC to work correctly, even the queues that you are not
using (you can just configure these queues with a very small ring buffer.)
The older uses the Cortex-M7 core r0p1 and the newer r1p1 revisions. The
SAMV71 revisions are called "rev A" (or sometimes "MRLA") and "rev B"
("MRLB"). There should be a small "A" or "B" on the chip package just below
the reference and you can also differentiate them at runtime with the
2017-03-30 20:29:19 +02:00
VERSION field in the CHIPID CIDR register.
2017-03-30 16:43:07 +02:00
2015-03-30 15:33:48 +02:00
Cache-Related Issues
--------------------
I- and D-Caches can be enabled but the D-Cache must be enabled in write-
through mode. This is to work around issues with the RX and TX descriptors
with are 8-bytes in size. But the D-Cache cache line size is 32-bytes.
That means that you cannot reload, clean or invalidate a descriptor without
also effecting three neighboring descriptors. Setting write through mode
eliminates the need for cleaning the D-Cache. If only reloading and
invalidating are done, then there is no problem.
2015-03-16 20:51:37 +01:00
Using the network with NSH
--------------------------
So what can you do with this networking support? First you see that
NSH has several new network related commands:
ifconfig, ifdown, ifup: Commands to help manage your network
get and put: TFTP file transfers
wget: HTML file transfers
ping: Check for access to peers on the network
Telnet console: You can access the NSH remotely via telnet.
You can also enable other add on features like full FTP or a Web
Server or XML RPC and others. There are also other features that
you can enable like DHCP client (or server) or network name
resolution.
2015-09-25 18:14:40 +02:00
By default, the IP address of the SAMV71-XULT will be 10.0.0.2 and
2015-03-16 20:51:37 +01:00
it will assume that your host is the gateway and has the IP address
10.0.0.1.
nsh> ifconfig
eth0 HWaddr 00:e0:de:ad:be:ef at UP
IPaddr:10.0.0.2 DRaddr:10.0.0.1 Mask:255.255.255.0
You can use ping to test for connectivity to the host (Careful,
Window firewalls usually block ping-related ICMP traffic). On the
target side, you can:
nsh> ping 10.0.0.1
PING 10.0.0.1 56 bytes of data
56 bytes from 10.0.0.1: icmp_seq=1 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=2 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=3 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=4 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=5 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=6 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=7 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=8 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=9 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=10 time=0 ms
10 packets transmitted, 10 received, 0% packet loss, time 10100 ms
NOTE: In this configuration is is normal to have packet loss > 0%
the first time you ping due to the default handling of the ARP
table.
2015-09-25 18:14:40 +02:00
On the host side, you should also be able to ping the SAMV71-XULT:
2015-03-16 20:51:37 +01:00
$ ping 10.0.0.2
You can also log into the NSH from the host PC like this:
$ telnet 10.0.0.2
Trying 10.0.0.2...
Connected to 10.0.0.2.
Escape character is '^]'.
sh_telnetmain: Session [3] Started
NuttShell (NSH) NuttX-7.9
nsh> help
help usage: help [-v] [<cmd>]
[ echo ifconfig mkdir mw sleep
? exec ifdown mkfatfs ping test
cat exit ifup mkfifo ps umount
cp free kill mkrd put usleep
cmp get losetup mh rm wget
dd help ls mount rmdir xd
df hexdump mb mv sh
Builtin Apps:
nsh>
NOTE: If you enable this feature, you experience a delay on booting.
That is because the start-up logic waits for the network connection
to be established before starting NuttX. In a real application, you
would probably want to do the network bringup on a separate thread
so that access to the NSH prompt is not delayed.
This delay will be especially long if the board is not connected to
a network. On the order of a minute! You will probably think that
NuttX has crashed! And then, when it finally does come up, the
network will not be available.
Network Initialization Thread
-----------------------------
There is a configuration option enabled by CONFIG_NSH_NETINIT_THREAD
that will do the NSH network bring-up asynchronously in parallel on
a separate thread. This eliminates the (visible) networking delay
altogether. This networking initialization feature by itself has
some limitations:
- If no network is connected, the network bring-up will fail and
the network initialization thread will simply exit. There are no
retries and no mechanism to know if the network initialization was
successful.
- Furthermore, there is no support for detecting loss of the network
connection and recovery of networking when the connection is restored.
Both of these shortcomings can be eliminated by enabling the network
monitor:
Network Monitor
---------------
By default the network initialization thread will bring-up the network
then exit, freeing all of the resources that it required. This is a
good behavior for systems with limited memory.
If the CONFIG_NSH_NETINIT_MONITOR option is selected, however, then the
network initialization thread will persist forever; it will monitor the
network status. In the event that the network goes down (for example, if
a cable is removed), then the thread will monitor the link status and
attempt to bring the network back up. In this case the resources
required for network initialization are never released.
Pre-requisites:
- CONFIG_NSH_NETINIT_THREAD as described above.
- CONFIG_NETDEV_PHY_IOCTL. Enable PHY IOCTL commands in the Ethernet
device driver. Special IOCTL commands must be provided by the Ethernet
driver to support certain PHY operations that will be needed for link
management. There operations are not complex and are implemented for
the Atmel SAMV7 family.
- CONFIG_ARCH_PHY_INTERRUPT. This is not a user selectable option.
Rather, it is set when you select a board that supports PHY interrupts.
In most architectures, the PHY interrupt is not associated with the
Ethernet driver at all. Rather, the PHY interrupt is provided via some
board-specific GPIO and the board-specific logic must provide support
for that GPIO interrupt. To do this, the board logic must do two things:
(1) It must provide the function arch_phy_irq() as described and
prototyped in the nuttx/include/nuttx/arch.h, and (2) it must select
CONFIG_ARCH_PHY_INTERRUPT in the board configuration file to advertise
that it supports arch_phy_irq(). This logic can be found at
2015-12-02 15:37:42 +01:00
nuttx/configs/samv71-xult/src/sam_ethernet.c.
2015-03-16 20:51:37 +01:00
- And a few other things: UDP support is required (CONFIG_NET_UDP) and
signals must not be disabled (CONFIG_DISABLE_SIGNALS).
Given those prerequisites, the network monitor can be selected with these
additional settings.
Networking Support -> Networking Device Support
CONFIG_NETDEV_PHY_IOCTL=y : Enable PHY ioctl support
Application Configuration -> NSH Library -> Networking Configuration
CONFIG_NSH_NETINIT_THREAD : Enable the network initialization thread
CONFIG_NSH_NETINIT_MONITOR=y : Enable the network monitor
CONFIG_NSH_NETINIT_RETRYMSEC=2000 : Configure the network monitor as you like
CONFIG_NSH_NETINIT_SIGNO=18
2015-08-16 18:59:35 +02:00
USBHS Device Controller Driver
==============================
The USBHS device controller driver is enabled with he following configuration
settings:
Device Drivers -> USB Device Driver Support
CONFIG_USBDEV=y : Enable USB device support
2015-08-22 18:14:36 +02:00
For full-speed/low-power mode:
CONFIG_USBDEV_DUALSPEED=n : Disable High speed support
For high-speed/normal mode:
2015-08-16 18:59:35 +02:00
CONFIG_USBDEV_DUALSPEED=y : Enable High speed support
CONFIG_USBDEV_DMA=y : Enable DMA methods
CONFIG_USBDEV_MAXPOWER=100 : Maximum power consumption
CONFIG_USBDEV_SELFPOWERED=y : Self-powered device
System Type -> SAMV7 Peripheral Selection
CONFIG_SAMV7_USBDEVHS=y
System Type -> SAMV7 USB High Sppeed Device Controller (DCD options
2015-08-22 18:14:36 +02:00
For full-speed/low-power mode:
CONFIG_SAMV7_USBDEVHS_LOWPOWER=y : Select low power mode
For high-speed/normal mode:
CONFIG_SAMV7_USBDEVHS_LOWPOWER=n : Don't select low power mode
CONFIG_SAMV7_USBHS_NDTDS=32 : Number of DMA transfer descriptors
2015-08-16 18:59:35 +02:00
CONFIG_SAMV7_USBHS_PREALLOCATE=y : Pre-allocate descriptors
2015-11-30 15:04:32 +01:00
As noted above, this driver will not work correctly if the write back
2015-12-01 00:37:01 +01:00
data cache is enabled. You must have:
2015-11-30 15:04:32 +01:00
2015-12-01 00:37:01 +01:00
CONFIG_ARMV7M_DCACHE_WRITETHROUGH=y
2015-11-30 15:04:32 +01:00
2015-08-16 18:59:35 +02:00
In order to be usable, you must all enabled some class driver(s) for the
USBHS device controller. Here, for example, is how to configure the CDC/ACM
serial device class:
Device Drivers -> USB Device Driver Support
CONFIG_CDCACM=y : USB Modem (CDC ACM) support
CONFIG_CDCACM_EP0MAXPACKET=64 : Enpoint 0 packet size
CONFIG_CDCACM_EPINTIN=1 : Interrupt IN endpoint number
CONFIG_CDCACM_EPINTIN_FSSIZE=64 : Full speed packet size
CONFIG_CDCACM_EPINTIN_HSSIZE=64 : High speed packet size
CONFIG_CDCACM_EPBULKOUT=3 : Bulk OUT endpoint number
CONFIG_CDCACM_EPBULKOUT_FSSIZE=64 : Full speed packet size
CONFIG_CDCACM_EPBULKOUT_HSSIZE=512 : High speed packet size
CONFIG_CDCACM_EPBULKIN=2 : Bulk IN endpoint number
CONFIG_CDCACM_EPBULKIN_FSSIZE=64 : Full speed packet size
CONFIG_CDCACM_EPBULKIN_HSSIZE=512 : High speed packet size
CONFIG_CDCACM_NWRREQS=4 : Number of write requests
2015-08-22 18:14:36 +02:00
CONFIG_CDCACM_NRDREQS=8 : Number of read requests
2015-12-08 14:32:47 +01:00
CONFIG_CDCACM_BULKIN_REQLEN=96 : Size of write request buffer (for full speed)
CONFIG_CDCACM_BULKIN_REQLEN=768 : Size of write request buffer (for high speed)
CONFIG_CDCACM_RXBUFSIZE=257 : Serial read buffer size
CONFIG_CDCACM_TXBUFSIZE=193 : Serial transmit buffer size (for full speed)
CONFIG_CDCACM_TXBUFSIZE=769 : Serial transmit buffer size (for high speed)
2015-08-16 18:59:35 +02:00
CONFIG_CDCACM_VENDORID=0x0525 : Vendor ID
CONFIG_CDCACM_PRODUCTID=0xa4a7 : Product ID
CONFIG_CDCACM_VENDORSTR="NuttX" : Vendor string
CONFIG_CDCACM_PRODUCTSTR="CDC/ACM Serial" : Product string
Device Drivers -> Serial Driver Support
CONFIG_SERIAL_REMOVABLE=y : Support for removable serial device
The CDC/ACM application provides commands to connect and disconnect the
CDC/ACM serial device:
CONFIG_SYSTEM_CDCACM=y : Enable connect/disconnect support
CONFIG_SYSTEM_CDCACM_DEVMINOR=0 : Use device /dev/ttyACM0
2015-08-22 18:14:36 +02:00
CONFIG_CDCACM_RXBUFSIZE=??? : A large RX may be needed
2015-08-16 18:59:35 +02:00
If you include this CDC/ACM application, then you can connect the CDC/ACM
serial device to the host by entering the command 'sercon' and you detach
the serial device with the command 'serdis'. If you do no use this
application, they you will have to write logic in your board initialization
code to initialize and attach the USB device.
2015-04-01 20:13:51 +02:00
Audio Interface
===============
WM8904 Audio Codec
------------------
SAMV71 Interface WM8904 Interface
---- ------------ ------- ----------------------------------
PIO Usage Pin Function
---- ------------ ------- ----------------------------------
PA3 TWD0 SDA I2C control interface, data line
PA4 TWCK0 SCLK I2C control interface, clock line
PA10 RD ADCDAT Digital audio output (microphone)
PB18 PCK2 MCLK Master clock
PB0 TF LRCLK Left/right data alignment clock
PB1 TK BCLK Bit clock, for synchronization
PD11 GPIO IRQ Audio interrupt
PD24 RF LRCLK Left/right data alignment clock
PD26 TD DACDAT Digital audio input (headphone)
---- ------------ ------- ----------------------------------
2015-04-02 21:00:10 +02:00
CP2100-CP Fractional-N Clock Multiplier
--------------------------------------
SAMV71 Interface CP2100-CP Interface
---- ------------ ------- ----------------------------------
PIO Usage Pin Function
---- ------------ ------- ----------------------------------
PA3 TWD0 SDA I2C control interface, data line
PA4 TWCK0 SCLK I2C control interface, clock line
PD21 TIOA11 CLK_IN PLL input
- - XTI/XTO 12.0MHz crystal
PA22 RK CLK_OUT PLL output
- - AUX_OUT N/C
---- ------------ ------- ----------------------------------
2015-03-30 23:31:53 +02:00
maXTouch Xplained Pro
=====================
Testing has also been performed using the maXTouch Xplained Pro LCD
2015-03-31 17:01:38 +02:00
(ATMXT-XPRO).
2015-05-13 01:59:45 +02:00
**************************************************************************
* WARNING: *
* The maXTouch chip was not configured on all of the maXTouch Xplained *
* Pro boards that I have used (which is two). The maXTouch is *
* completely non-functional with no configuration in its NV memory! *
* *
* My understanding is that this configuration can be set on Linux *
* using the mxp-app program which is available on GitHub. There is an *
* (awkward) way to do this with NuttX too. In order to set the *
* maXTouch configuration with Nuttx you need to do these things: *
* *
* - Copy the function atmxt_config() from the file *
* configs/samv71-xult/src/atmxt_config.c into the file *
* drivers/input/mxt.c *
* - Add a call to atmxt_config() in drivers/input/mxt.c in the *
* function mxt_register() just before the touchscreen device is *
* registered (i.e, the call to register_driver()). *
* - Run the code one time. Your maXTouch is configured and should *
* now work. *
* - Don't forget to remove atmxt_config() from drivers/input/mxt.c and *
* restore driver as it was. *
* *
**************************************************************************
2015-03-31 17:01:38 +02:00
maXTouch Xplained Pro Standard Extension Header
-----------------------------------------------
The LCD could be connected either via EXT1 or EXT2 using the 2x10 20-pin
2015-04-04 19:49:15 +02:00
cable and the maXTouch Xplained Pro standard extension header. Access would
then be performed in SPI mode.
NOTE: There is currently no support for use of the LCD in SPI mode. See
the next paragraph where the LCD/EXT4 connection is discussion.
2015-03-31 17:01:38 +02:00
NOTE the 3 switch mode selector on the back of the maXtouch. All switches
should be in the ON position to select 4-wire SPI mode.
2015-03-30 23:31:53 +02:00
---- -------- ---- ----------- ---- ----------- ------------------------------------------
SAMV71-XULT maxTouch Xplained Pro
PIN FUNCTION EXT1 FUNC EXT2 FUNC Description
---- -------- ---- ----------- ---- ----------- ------------------------------------------
1 ID - - - - Communication line to ID chip
2 GND - - - - Ground
3 N/C PC31 - PD30 -
4 N/C PA19 - PC13 -
5 GPIO PB3 GPIO PA6 GPIO Command/Data Select
6 N/C PB2 - PD11 -
7 PWM PA0 PWMC0_PWMH0 PC19 PWMC0_PMWH2 Backlight control
8 N/C PC30 - PD26 -
9 GPIO/IRQ PD28 GPIO PA2 GPIO IRQ from maXTouch controller
10 GPIO PA5 GPIO PA24 GPIO RESET signal for maXTouch and LCD controller
11 I2C SDA PA3 TWID0 PA3 TWID0 I2C Data line for maXTouch controller
12 I2C SCL PA4 TWICK0 PA4 TWICK0 I2C Clock line for maXTouch controller
13 N/C PB0 - PA21 -
14 N/C PB1 - PB4 -
15 CS PD25 GPIO PD27 GPIO CS line for LCD controller
16 SPI MOSI PD21 SPI0_MOSI PD21 SPI0_MOSI SPI Data to LCD controller
17 SPI MISO PD20 SPI0_MISO PD20 SPI0_MISO SPI Data from LCD controller
18 SPI SCK PD22 SPI0_SPCK PD22 SPI0_SPCK SPI Clock line
19 GND - - - - Ground
20 VCC - - - - Target supply voltage
---- -------- ---- ----------- ---- ----------- ------------------------------------------
NOTE: Use of EXT1 conflicts with the Arduino RXD pin (PD28). You cannot
2015-03-31 17:01:38 +02:00
put the maXTouch Xplained in EXT1 and also use the Arduino RXD/TXD pins
2015-03-30 23:31:53 +02:00
as your serial console.
2015-03-31 17:01:38 +02:00
maXTouch Xplained Pro Xplained Pro LCD Connector
------------------------------------------------
It is also possible to connect the LCD via the flat cable to the EXT4 LCD
connector. In this case, you would use the SMC/EBI to communicate with the
LCD.
2015-04-04 22:05:42 +02:00
NOTE: (1) Only the parallel interface is supported by the SAMV71-XULT and (2)
the 3 switch mode selector on the back of the maXtouch. These switches should
be in the OFF-ON-OFF positions to select 16-bit color mode.
2015-03-31 17:01:38 +02:00
----------------- ------------- -----------------------------------------------------------
LCD SAMV71 Description
Pin Function Pin Function
---- ------------ ---- -------- -----------------------------------------------------------
1 ID - - Communication line to ID chip on extension board
2 GND - GND Ground
3 D0 PC0 D0 Data line
4 D1 PC1 D1 Data line
5 D2 PC2 D2 Data line
6 D3 PC3 D3 Data line
7 GND - GND Ground
8 D4 PC4 D4 Data line
9 D5 PC5 D5 Data line
10 D6 PC6 D6 Data line
11 D7 PC7 D7 Data line
12 GND - GND Ground
13 D8 PE0 D8 Data line
14 D9 PE1 D9 Data line
15 D10 PE2 D10 Data line
16 D11 PE3 D11 Data line
17 GND - GND Ground
18 D12 PE4 D12 Data line
19 D13 PE5 D13 Data line
20 D14 PA15 D14 Data line
21 D15 PA16 D15 Data line
22 GND - GND Ground
23 D16 - - Data line
24 D17 - - Data line
25 N/C - -
26 N/C - -
27 GND - GND Ground
28 N/C - -
29 N/C - -
30 N/C - -
31 N/C - -
32 GND - GND Ground
2015-04-04 22:05:42 +02:00
33 PCLK/ PC30 GPIO SMC: Pixel clock Display RAM select.
CMD_DATA_SEL SPI: One address line of the MCU for displays where it
2015-03-31 17:01:38 +02:00
is possible to select either the register or the
data interface
2015-04-04 22:05:42 +02:00
34 VSYNC/CS PD19 NCS3 SMC: Vertical synchronization.
SPI: Chip select
35 HSYNC/WE PC8 NWE SMC: Horizontal synchronization
SPI: Write enable signal
36 DATA ENABLE/ PC11 NRD SMC: Data enable signal
RE SPI: Read enable signal
37 SPI SCK - - SPI: Clock for SPI
38 SPI MOSI - - SPI: Master out slave in line of SPI
39 SPI MISO - - SPI: Master in slave out line of SPI
40 SPI SS - - SPI: Slave select for SPI
2015-03-31 17:01:38 +02:00
41 N/C - -
42 TWI SDA PA3 TWD0 I2C data line (maXTouch®)
43 TWI SCL PA4 TWCK0 I2C clock line (maXTouch)
44 IRQ1 PD28 WKUP5 maXTouch interrupt line
45 N/C PA2 WKUP2
46 PWM PC9 TIOB7 Backlight control
47 RESET PC13 GPIO Reset for both display and maxTouch
48 VCC - - 3.3V power supply for extension board
49 VCC - - 3.3V power supply for extension board
50 GND - - Ground
---- ------------ ---- -------- -----------------------------------------------------------
2015-04-04 19:49:15 +02:00
NOTE: Use of LCD/EXT4 conflicts with the Arduino RXD pin (PD28). You cannot
put the maXTouch Xplained in LCD/EXT4 and also use the Arduino RXD/TXD pins
as your serial console.
2015-04-04 16:43:41 +02:00
Connecting the flat cable. I was embarrassed to say that I did not know how
the connectors worked. Let me share this so that, perhaps, I can save you
the same embarrassment:
- The maXTouch Xplained Pro has an Omron XF2M-5015-1A connector. There is a
black bar at back (toward the baord). Raise that bar and insert the cable
with the contacts away from the board. Lower that bar to lock the cable
in place.
- The SAMV71-Xult has a TE Connectivity 5-1734839-0 FPC connector that works
differently. On each size of the connector are two small white tabs. Pull
these out and away from the board. Insert the ribbon with the contacts
toward the board. Lock the cable in place by pushing the tabs back in
place.
2015-04-04 04:12:30 +02:00
MXT Configuration Options
2015-03-31 17:01:38 +02:00
-------------------------
2015-03-30 23:31:53 +02:00
System Type -> SAMV7 Peripheral Support
CONFIG_SAMV7_TWIHS0=y : Needed by the MaXTouch controller
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
Board Selection ->
CONFIG_SAMV71XULT_MXTXPLND=y : MaXTouch Xplained is connected
CONFIG_SAMV71XULT_MXTXPLND_EXT1=y : Connected on EXT1, or
2015-03-31 17:01:38 +02:00
CONFIG_SAMV71XULT_MXTXPLND_EXT2=y : Connected on EXT2, or
CONFIG_SAMV71XULT_MXTXPLND_LCD=y : Connected on LCD
2015-03-30 23:31:53 +02:00
CONFIG_SAMV71XULT_MXT_DEVMINOR=0 : Register as /dev/input0
CONFIG_SAMV71XULT_MXT_I2CFREQUENCY=400000
NOTE: When selecting EXT1 or EXT2, be conscious of possible pin conflicts.
EXT1, for example, will conflict with the use of the Arduino TXD and RXD
pins for the serial console
Device Drivers -> Input Devices
CONFIG_INPUT=y : Enable support for human input devices
CONFIG_INPUT_MXT=y : Enable support for the maXTouch controller
The following enables a small built-in application that can be used to
test the touchscreen:
Application Configuration -> Examples -> Touchscreen example
CONFIG_EXAMPLES_TOUCHSCREEN=y : Enables the example
CONFIG_EXAMPLES_TOUCHSCREEN_ARCHINIT=y : Have board-specific intialization
CONFIG_EXAMPLES_TOUCHSCREEN_DEVPATH="/dev/input0"
CONFIG_EXAMPLES_TOUCHSCREEN_MINOR=0
2015-04-04 04:12:30 +02:00
ILI9488 Configuration Options
-----------------------------
2015-08-05 16:05:26 +02:00
Currently only the parallel mode is supported. This means that the LCD can
only be used in connected in the LCD (EXT4) connection.
2015-04-04 04:12:30 +02:00
System Type -> SAMV7 Peripheral Support
CONFIG_SAMV7_SMC=y : Needed by the ILI9466 driver controller
CONFIG_SAMV7_XDMAC=y : Needed by the ILI9466 driver
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
Board Selection ->
CONFIG_SAMV71XULT_MXTXPLND=y : MaXTouch Xplained is connected
CONFIG_SAMV71XULT_MXTXPLND_LCD=y : Must be connected on LCD
NOTE: When selecting EXT1 or EXT2, be conscious of possible pin conflicts.
EXT1, for example, will conflict with the use of the Arduino TXD and RXD
pins for the serial console
Device Drivers -> LCD drivers
CONFIG_LCD=y : Enable support for LCDs
Graphics
CONFIG_NX=y : Enable Graphics supported
CONFIG_NX_LCDDRIVER=y : Enable LCD driver support
CONFIG_NX_DISABLE_*BPP=y : When * is {1,2,4,8,24, and 32}
CONFIG_NXFONTS_CHARBITS=7
CONFIG_NXFONT_SANS23X27=y : One font must be enabled
There are several graphics examples that can be enabled under apps/examples.
nxlines is one of these and can be enabled as follows. See
apps/examples/README.txt for information about configuring other graphics
examples.
The following enables a small built-in application that can be used to
test the touchscreen:
Application Configuration -> Examples -> NX lines example
CONFIG_EXAMPLES_NXLINES=y : Enables the nxlines example
CONFIG_EXAMPLES_NXLINES_VPLANE=0
CONFIG_EXAMPLES_NXLINES_DEVNO=0
2015-08-05 16:05:26 +02:00
MCAN1 Loopback Test
===================
MCAN1
-----
SAM V71 Xplained Ultra has two MCAN modules that performs communication according
to ISO11898-1 (Bosch CAN specification 2.0 part A,B) and Bosch CAN FD
specification V1.0. MCAN1 is connected to an on-board ATA6561 CAN physical-layer
transceiver.
------- -------- -------- -------------
SAM V71 FUNCTION ATA6561 SHARED
PIN FUNCTION FUNCTIONALITY
------- -------- -------- -------------
PC14 CANTX1 TXD Shield
PC12 CANRX1 RXD Shield
------- -------- -------- -------------
Enabling MCAN1
--------------
These modifications may be applied to the samv71-xult/nsh configuration in order
to enable MCAN1:
Device Drivers -> CAN Driver support
CONFIG_CAN=y # Enable the upper-half CAN driver
CONFIG_CAN_FIFOSIZE=8
CONFIG_CAN_NPENDINGRTR=4
System Type -> SAMV7 Peripheral Selections
CONFIG_SAMV7_MCAN1=y # Enable MCAN1 as the lower-half
2015-08-05 16:21:50 +02:00
System Type -> MCAN device driver options
2015-08-05 16:05:26 +02:00
CONFIG_SAMV7_MCAN_CLKSRC_MAIN=y # Use the MAIN clock as the source
CONFIG_SAMV7_MCAN_CLKSRC_PRESCALER=1
System Type ->MCAN device driver options -> MCAN1 device driver options
CONFIG_SAMV7_MCAN1_ISO11899_1=y # Loopback test only support ISO11899-1
CONFIG_SAMV7_MCAN1_LOOPBACK=y # Needed for loopback test
CONFIG_SAMV7_MCAN1_BITRATE=500000 # Not critical for loopback test
CONFIG_SAMV7_MCAN1_PROPSEG=2 # Bit timing setup
CONFIG_SAMV7_MCAN1_PHASESEG1=11 # " " " " " "
CONFIG_SAMV7_MCAN1_PHASESEG2=11 # " " " " " "
CONFIG_SAMV7_MCAN1_FSJW=4 # " " " " " "
CONFIG_SAMV7_MCAN1_FBITRATE=2000000 # CAN_FD BTW mode is not used
CONFIG_SAMV7_MCAN1_FPROPSEG=2 # " " " " " " "" " " " "
CONFIG_SAMV7_MCAN1_FPHASESEG1=4 # " " " " " " "" " " " "
CONFIG_SAMV7_MCAN1_FPHASESEG2=4 # " " " " " " "" " " " "
CONFIG_SAMV7_MCAN1_FFSJW=2 # " " " " " " "" " " " "
CONFIG_SAMV7_MCAN1_NSTDFILTERS=0 # Filters are not used in the loopback test
CONFIG_SAMV7_MCAN1_NEXTFILTERS=0 # " " " " " " " " "" " " " " " "
CONFIG_SAMV7_MCAN1_RXFIFO0_32BYTES=y # Each RX FIFO0 element is 32 bytes
CONFIG_SAMV7_MCAN1_RXFIFO0_SIZE=8 # There are 8 queue elements
CONFIG_SAMV7_MCAN1_RXFIFO0_32BYTES=y # Each RX FIFO1 element is 32 bytes
CONFIG_SAMV7_MCAN1_RXFIFO0_SIZE=8 # There are 8 queue elements
CONFIG_SAMV7_MCAN1_RXBUFFER_32BYTES=y # Each RX BUFFER is 32 bytes
CONFIG_SAMV7_MCAN1_TXBUFFER_32BYTES=y # Each TX BUFFER is 32 bytes
CONFIG_SAMV7_MCAN1_TXFIFOQ_SIZE=8 # There are 8 queue elements
CONFIG_SAMV7_MCAN1_TXEVENTFIFO_SIZE=0 # The event FIFO is not used
Enabling the CAN Loopback Test
------------------------------
Application Configuration -> Examples -> CAN Example
CONFIG_EXAMPLES_CAN=y # Enables the CAN test
Enabling CAN Debug Output
-------------------------
2015-08-05 16:21:50 +02:00
Build Setup -> Debug Options
2016-06-11 22:14:08 +02:00
CONFIG_DEBUG_FEATURES=y # Enables general debug features
CONFIG_DEBUG_INFO=y # Enables verbose output
2016-06-15 23:45:27 +02:00
CONFIG_DEBUG_CAN_INFO=y # Enables debug output from CAN
2015-08-05 17:16:56 +02:00
2015-08-05 16:21:50 +02:00
CONFIG_STACK_COLORATION=y # Monitor stack usage
CONFIG_DEBUG_SYMBOLS=y # Needed only for use with a debugger
2015-08-05 17:16:56 +02:00
CONFIG_DEBUG_NOOPT=y # Disables optimization
2015-08-05 16:21:50 +02:00
System Type -> MCAN device driver options
CONFIG_SAMV7_MCAN_REGDEBUG=y # Super low level register debug output
2015-08-05 16:05:26 +02:00
2015-08-11 17:30:52 +02:00
SPI Slave
=========
An interrutp driven SPI slave driver as added on 2015-08-09 but has not
been verified as of this writing. See discussion in include/nuttx/spi/slave.h
and below.
I do not yet have a design that supports SPI slave DMA. And, under
certain, very limited conditions, I think it can be done. Those
certain conditions are:
a) The master does not tie the chip select to ground. The master must
raise chip select at the end of the transfer. Then I do not need to
know the length of the transfer; I can cancel the DMA when the chip
is de-selected.
b) The protocol includes a dummy read after sending the command. This
is very common in SPI device and should not be an issue if it is
specified. This dummy read time provides time to set up the DMA.
So the protocol would be:
i) Master drops the chip select.
ii) Master sends the command which will indicate whether the master
is reading, writing, or exchanging data. The master discards
the garbage return value.
iii) Slave is interrupted when the command word is received. The
SPI device then decodes the command word and setups up the
subsequent DMA.
iv) Master sends a dummy word and discards the return value.
During the bit times to shift the dummy word, the slave has time
to set up the DMA.
v) Master then reads or writes (or exchanges) the data If the DMA
is in place, the transfer should continue normally.
vi) At the end of the data transfer the master raises the chip
select.
c) There are limitations in the word time, i.e., the time between the
interrupt for each word shifted in from the master.
The controller driver will get events after the receipt of each word in
ii), iv), and v). The time between each word will be:
word-time = nbits * bit time + inter-word-gap
So for an 8 bit interface at 20MHz, the words will be received from the
master a 8 * 50nsec = 400 nsec + inter-word-gap. That is the time
during which the dummy word would be shifted and during which we
receive the interrupt for the command word, interpret the command word,
and to set up the DMA for the remaining word transfer. I don't think
that is possible, at least not at 20 MHz.
That is far too fast even for the interrupt driven solution that I have
in place now. It could not work at 20MHz. If we suppose that interrupt
processing is around 1 usec, then an 8 bit interface could not have bit
times more than 125 nsec or 8 KHz. Interrupt handling should be faster
than 1 usec, but not a lot faster. I have not benchmarked it. NuttX
also supports special, zero latency interrupts that could bring the
interrupt time down even more.
Note that we would also have a little more processing time if you used
16-bit SPI word size.
Note also that the interrupt driven approach would have this same basic
performance limitation with the additional disadvantage that:
a) The driver will receive two interrupts per word exchanged:
i) One interrupt will be received when the word is shifted in from
the master (at the end of 8-bit times). This is a data received
interrupt.
ii) And another interrupt when the next words moved to the shift-out
register, freeing up the transmit holding register. This is the
data sent interrupt.
The ii) event should be very soon after the i) event.
Without DMA, the only way to reduce the interrupt rate would be to add
interrupt-level polling to detect the when transmit holding register
is available. That is not really a good idea.
b) It will hog all of the CPU for the duration of the transfer).
2017-07-02 19:04:57 +02:00
Click Shield
============
In the mrf24j40-starhub configuration, a click shield from
MikroElectronika was used along with a Click "Bee" module. The click
shield supports two click shields and the following tables describe the
relationship between the pins on each click shield, the Arduino
2017-07-04 22:31:26 +02:00
connector and the SAMV71 pins.
2017-07-02 19:04:57 +02:00
--------- ---------------------- -------- --------- ------------------ ----------
2017-07-04 22:31:26 +02:00
mikroBUS1 Arduino SAMV71 mikroBUS2 Arduino SAMV71
2017-07-02 19:04:57 +02:00
--------- ---------------------- -------- --------- ------------------ ----------
AN HD1 A0 AN0 Pin 1 AD0 PD26 AN HD1 A1 AN1 Pin 2 AD1 PC31
2017-07-04 22:31:26 +02:00
RST HD1 A3 Pin 4 AD3 PA19 RST HD1 A2 Pin 3 AD2 PD30
2017-07-02 19:04:57 +02:00
CS HD4 D10 SPI-SS Pin 8 D10 PD25 CS HD4 D9 Pin 9 D9 PC9
SCK HD4 D13 SPI-SCK Pin 5 D13 PD22 SCK Same
MISO HD4 D12 SPI-MISO Pin 6 D12 PD20 MISO Same
MOSI HD4 D11 SPI-MOSI Pin 7 D11 PD21 MOSI Same
3.3V N/A 3.3V N/A
GND N/A GND N/A
2017-07-04 22:31:26 +02:00
PWM HD3 D6 PWMA Pin 2 D6 PC19 PWM HD3 D5 PWMB Pin 5 D5 PD11
2017-07-02 19:04:57 +02:00
INT HD3 D2 INT0 Pin 6 D2 PA5 INT HD3 D3 INT1 Pin 5 D3 PA6
RX HD3 D0 HDR-RX* Pin 8 D0 PD28 RX Same
2017-07-04 22:31:26 +02:00
TX HD3 D1 HDR-TX* Pin 7 D1 PD30 TX Same
SCL HD1 A5 I2C-SCL Pin 5 AD5 PC30 SDA Same
2017-07-02 19:04:57 +02:00
SDA HD1 A4 I2C-SDA Pin 6 AD4 PC13 SCL Same
5V N/A 5V N/A
GND N/A GND N/A
--------- ---------------------- -------- --------- ------------------ ----------
* Depends upon setting of SW1, UART vs PROG.
--- ----- ------------------------------ ---------------------------------
2017-07-04 22:31:26 +02:00
PIN PORT SHIELD FUNCTION SAMV71PIN CONFIGURATION
2017-07-02 19:04:57 +02:00
--- ----- ------------------------------ ---------------------------------
2017-07-03 19:51:39 +02:00
AD0 PD26 microBUS2 Analog TD PD26 *** Not an AFE pin ***
AD1 PC31 microBUS2 Analog PC31 AFE1_AD6 GPIO_AFE1_AD6
AD2 PD30 microBUS2 GPIO reset output PD30
AD3 PA19 microBUS1 GPIO reset output PA19
AD4 PC13 (both) I2C-SDA PC13 *** Does not support I2C SDA ***
AD5 PC30 (both) I2C-SCL PC30 *** Does not support I2C SCL ***
AD6 PA17 *** Not used ***
AD7 PC12 *** Not used ***
D0 PD28 (both) HDR_RX PD28 URXD3 GPIO_UART3_RXD
D1 PD30 (both) HDR_TX PD30 UTXD3 GPIO_UART3_TXD_1
D2 PA5 microBUS1 GPIO interrupt input PA5
D3 PA6 microBUS2 GPIO interrupt input PA6
D4 PD27 *** Not used ***
D5 PD11 microBUS2 PWM PD11 PWMC0_H0
D6 PC19 microBUS1 PWN PC19 PWMC0_H2
D7 PA2 *** Not used ***
2017-07-03 20:06:17 +02:00
D8 PA17 *** Not used ***
2017-07-03 19:51:39 +02:00
D9 PC9 microBUS2 CS GPIO output PC9
D10 PD25 microBUS1 CS GPIO output PD25 SPI0_NPCS1
D11 PD21 (both) SPI-MOSI PD21 SPI0_MOSI GPIO_SPI0_MOSI
D12 PD20 (both) SPI-MISO PD20 SPI0_MISO GPIO_SPI0_MISO
D13 PD22 (both) SPI-SCK PD22 SPI0_SPCK GPIO_SPI0_SPCK
2017-07-02 19:04:57 +02:00
2015-12-02 15:37:42 +01:00
Tickless OS
===========
Background
----------
By default, a NuttX configuration uses a periodic timer interrupt that
drives all system timing. The timer is provided by architecture-specific
code that calls into NuttX at a rate controlled by CONFIG_USEC_PER_TICK.
The default value of CONFIG_USEC_PER_TICK is 10000 microseconds which
corresponds to a timer interrupt rate of 100 Hz.
An option is to configure NuttX to operation in a "tickless" mode. Some
limitations of default system timer are, in increasing order of
importance:
- Overhead: Although the CPU usage of the system timer interrupt at 100Hz
is really very low, it is still mostly wasted processing time. One most
timer interrupts, there is really nothing that needs be done other than
incrementing the counter.
- Resolution: Resolution of all system timing is also determined by
CONFIG_USEC_PER_TICK. So nothing that be time with resolution finer than
10 milliseconds be default. To increase this resolution,
CONFIG_USEC_PER_TICK an be reduced. However, then the system timer
interrupts use more of the CPU bandwidth processing useless interrupts.
- Power Usage: But the biggest issue is power usage. When the system is
IDLE, it enters a light, low-power mode (for ARMs, this mode is entered
with the wfi or wfe instructions for example). But each interrupt
awakens the system from this low power mode. Therefore, higher rates
of interrupts cause greater power consumption.
The so-called Tickless OS provides one solution to issue. The basic
concept here is that the periodic, timer interrupt is eliminated and
replaced with a one-shot, interval timer. It becomes event driven
instead of polled: The default system timer is a polled design. On
each interrupt, the NuttX logic checks if it needs to do anything
and, if so, it does it.
Using an interval timer, one can anticipate when the next interesting
OS event will occur, program the interval time and wait for it to fire.
When the interval time fires, then the scheduled activity is performed.
Configuration
-------------
The following configuration options will enable support for the Tickless
2015-12-02 22:54:20 +01:00
OS for the SAMV7 platforms using TC0 channels 0-1 (other timers or
2015-12-02 15:37:42 +01:00
timer channels could be used making the obvious substitutions):
RTOS Features -> Clocks and Timers
CONFIG_SCHED_TICKLESS=y : Configures the RTOS in tickless mode
CONFIG_SCHED_TICKLESS_ALARM=n : (option not implemented)
2015-12-02 16:22:26 +01:00
CONFIG_SCHED_TICKLESS_LIMIT_MAX_SLEEP=y
2015-12-02 15:37:42 +01:00
System Type -> SAMV7 Peripheral Support
CONFIG_SAMV7_TC0=y : Enable TC0 (TC channels 0-3
System Type -> Timer/counter Configuration
CONFIG_SAMV7_ONESHOT=y : Enables one-shot timer wrapper
CONFIG_SAMV7_FREERUN=y : Enabled free-running timer wrapper
CONFIG_SAMV7_TICKLESS_ONESHOT=0 : Selects TC0 channel 0 for the one-shot
CONFIG_SAMV7_TICKLESS_FREERUN=1 : Selects TC0 channel 1 for the free-
: running timer
2015-12-03 01:54:17 +01:00
The resolution of the clock is provided by the CONFIG_USEC_PER_TICK
setting in the configuration file.
2015-12-02 15:37:42 +01:00
NOTE: In most cases, the slow clock will be used as the timer/counter
2015-12-02 22:54:20 +01:00
input. The 32.768KHz crystal is selected by the definition
BOARD_HAVE_SLOWXTAL in the configs/samv71-xult/board.h file.
2015-12-02 15:37:42 +01:00
2015-12-03 16:52:50 +01:00
The slow clock has a resolution of about 30.518 microseconds. Ideally,
the value of CONFIG_USEC_PER_TICK should be the exact clock resolution.
Otherwise there will be cumulative timing inaccuracies. But a choice
2015-12-03 01:54:17 +01:00
choice of:
2015-12-03 16:52:50 +01:00
CONFIG_USEC_PER_TICK=31
2015-12-03 01:54:17 +01:00
2015-12-03 16:52:50 +01:00
will have an error of 0.6% and will have inaccuracies that will
effect the time due to long term error build-up.
2015-12-03 01:54:17 +01:00
2015-12-04 19:37:00 +01:00
Using the slow clock clock input, the Tickless support is functional,
however, there are inaccuracies in delays. For example,
2015-12-03 16:52:50 +01:00
nsh> sleep 10
results in a delay of maybe 5.4 seconds. But the timing accuracy is
correct if all competing uses of the interval timer are disabled (mostly
from the high priority work queue). Therefore, I conclude that this
inaccuracy is due to the inaccuracies in the representation of the clock
rate. 30.518 usec cannot be represented accurately. Each timing
calculation results in a small error. When the interval timer is very
busy, long delays will be divided into many small pieces and each small
piece has a large error in the calculation. The cumulative error is the
cause of the problem.
2015-12-04 19:37:00 +01:00
Solution: The samv71-xult/src/sam_boot.c file has additional logic
to enable the programmable clock PCK6 as a clock source for the
timer/counters if the Tickless mode is selected. The ideal frequency
would be:
frequency = 1,000,000 / CONFIG_USEC_PER_TICK
The main crystal is selected as the frequency source. The maximum
prescaler value is 256 so the minimum frequency is 46,875 Hz which
corresponds to a period of 21.3 microseconds. A value of
CONFIG_USEC_PER_TICK=20, or 50KHz, would give an exact solution with
a divider of 240.
2015-12-03 01:54:17 +01:00
2015-12-02 15:37:42 +01:00
SAMV7 Timer Usage
-----------------
This current implementation uses two timers: A one-shot timer to
provide the timed events and a free running timer to provide the current
time. Since timers are a limited resource, that could be an issue on
some systems.
We could do the job with a single timer if we were to keep the single
timer in a free-running at all times. The SAMV7 timer/counters have
16-bit counters with the capability to generate a compare interrupt when
the timer matches a compare value but also to continue counting without
stopping (giving another, different interrupt when the timer rolls over
from 0xffff to zero). So we could potentially just set the compare at
the number of ticks you want PLUS the current value of timer. Then you
could have both with a single timer: An interval timer and a free-
running counter with the same timer! In this case, you would want to
to set CONFIG_SCHED_TICKLESS_ALARM in the NuttX configuration.
Patches are welcome!
2015-03-10 23:11:28 +01:00
Debugging
=========
2015-08-05 16:05:26 +02:00
The on-board EDBG appears to work only with Atmel Studio. You can however,
simply connect a SAM-ICE or J-Link to the JTAG/SWD connector on the board
and that works great. The only tricky thing is getting the correct
orientation of the JTAG connection.
2015-03-10 23:11:28 +01:00
2015-08-05 16:05:26 +02:00
I have been using Atmel Studio to write code to flash then I use the Segger
2017-07-02 21:06:23 +02:00
J-Link GDB server to debug. I have been using the 'Device Programming'
2015-08-05 16:05:26 +02:00
available under the Atmel Studio 'Tool' menu. I have to disconnect the
2017-07-02 21:06:23 +02:00
SAM-ICE while programming with the EDBG.
You can also load code into flash directory with J-Link:
arm-none-eabi-gdb
(gdb) target remote localhost:2331
(gdb) mon reset
(gdb) mon halt
(gdb) load nuttx
2015-03-10 23:11:28 +01:00
2015-08-05 16:05:26 +02:00
I run GDB like this from the directory containing the NuttX ELF file:
2015-03-10 23:11:28 +01:00
2015-08-05 16:05:26 +02:00
arm-none-eabi-gdb
(gdb) target remote localhost:2331
(gdb) mon reset
(gdb) file nuttx
(gdb) ... start debugging ...
2015-03-10 23:11:28 +01:00
2015-03-09 15:23:09 +01:00
Configurations
==============
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
Information Common to All Configurations
----------------------------------------
Each SAMV71-XULT configuration is maintained in a sub-directory and
can be selected as follow:
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
cd tools
./configure.sh samv71-xult/<subdir>
cd -
2015-03-10 02:58:59 +01:00
2017-05-11 21:35:56 +02:00
Before building, make sure the PATH environment variable include the
2017-04-26 18:12:13 +02:00
correct path to the directory than holds your toolchain binaries.
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
And then build NuttX by simply typing the following. At the conclusion of
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
make oldconfig
make
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
The <subdir> that is provided above as an argument to the tools/configure.sh
must be is one of the following.
2015-03-10 02:58:59 +01:00
2015-03-10 23:11:28 +01:00
NOTES:
2015-03-10 02:58:59 +01:00
1. These configurations use the mconf-based configuration tool. To
change any of these configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
2015-06-28 16:08:57 +02:00
see additional README.txt files in the NuttX tools repository.
2015-03-10 02:58:59 +01:00
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Unless stated otherwise, all configurations generate console
2015-04-04 16:43:41 +02:00
output on UART3 (i.e., for the Arduino serial shield).
2015-03-10 02:58:59 +01:00
3. All of these configurations are set up to build under Windows using the
2015-03-11 19:16:27 +01:00
"GNU Tools for ARM Embedded Processors" that is maintained by ARM
(unless stated otherwise in the description of the configuration).
https://launchpad.net/gcc-arm-embedded
As of this writing (2015-03-11), full support is difficult to find
2015-07-31 16:40:40 +02:00
for the Cortex-M7, but is supported by at least this realeasse of
2015-03-11 19:16:27 +01:00
the ARM GNU tools:
2015-07-31 16:40:40 +02:00
https://launchpadlibrarian.net/209776344/release.txt
2015-03-11 19:16:27 +01:00
That toolchain selection can easily be reconfigured using
'make menuconfig'. Here are the relevant current settings:
2015-03-10 02:58:59 +01:00
Build Setup:
2015-03-11 19:16:27 +01:00
CONFIG_HOST_WINDOWS=y : Window environment
CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows
2015-03-10 02:58:59 +01:00
System Type -> Toolchain:
2015-03-11 19:16:27 +01:00
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain
2015-03-10 02:58:59 +01:00
2015-03-29 21:09:22 +02:00
NOTE: As of this writing, there are issues with using this tool at
the -Os level of optimization. This has not been proven to be a
compiler issue (as least not one that might not be fixed with a
well placed volatile qualifier). However, in any event, it is
recommend that you use not more that -O2 optimization.
2015-03-10 23:11:28 +01:00
Configuration sub-directories
-----------------------------
2015-03-10 02:58:59 +01:00
2015-11-18 18:45:01 +01:00
knsh:
This is identical to the nsh configuration below except that NuttX
2017-01-23 17:38:54 +01:00
is built as a protected mode, monolithic module and the user applications
2015-11-18 18:45:01 +01:00
are built separately. There are four very similar NSH configurations:
- knsh. This is a somewhat simplified version of the nsh configuration
that builds using the protected build mode (CONFIG_BUILD_PROTECTED=y).
- nsh. This configuration is focused on low level, command-line
driver testing. It has no network.
- netnsh. This configuration is focused on network testing and
has only limited command support.
- mxtxplnd. This configuration is identical to the nsh configuration
but assumes that you have a maXTouch Xplained Pro LCD attached
and includes extra tests for the touchscreen and LCD.
It is recommends to use a special make command; not just 'make' but make
with the following two arguments:
make pass1 pass2
In the normal case (just 'make'), make will attempt to build both user-
and kernel-mode blobs more or less interleaved. This actual works!
However, for me it is very confusing so I prefer the above make command:
Make the user-space binaries first (pass1), then make the kernel-space
binaries (pass2)
NOTES:
1. At the end of the build, there will be several files in the top-level
NuttX build directory:
PASS1:
nuttx_user.elf - The pass1 user-space ELF file
nuttx_user.hex - The pass1 Intel HEX format file (selected in defconfig)
User.map - Symbols in the user-space ELF file
PASS2:
nuttx - The pass2 kernel-space ELF file
nuttx.hex - The pass2 Intel HEX file (selected in defconfig)
System.map - Symbols in the kernel-space ELF file
The J-Link programmer will except files in .hex, .mot, .srec, and .bin
formats.
2. Combining .hex files. If you plan to use the .hex files with your
debugger or FLASH utility, then you may need to combine the two hex
files into a single .hex file. Here is how you can do that.
a. The 'tail' of the nuttx.hex file should look something like this
(with my comments added):
$ tail nuttx.hex
# 00, data records
...
:10 9DC0 00 01000000000800006400020100001F0004
:10 9DD0 00 3B005A0078009700B500D400F300110151
:08 9DE0 00 30014E016D0100008D
# 05, Start Linear Address Record
:04 0000 05 0800 0419 D2
# 01, End Of File record
:00 0000 01 FF
Use an editor such as vi to remove the 05 and 01 records.
b. The 'head' of the nuttx_user.hex file should look something like
this (again with my comments added):
$ head nuttx_user.hex
# 04, Extended Linear Address Record
:02 0000 04 0801 F1
# 00, data records
:10 8000 00 BD89 01084C800108C8110208D01102087E
:10 8010 00 0010 00201C1000201C1000203C16002026
:10 8020 00 4D80 01085D80010869800108ED83010829
...
Nothing needs to be done here. The nuttx_user.hex file should
be fine.
c. Combine the edited nuttx.hex and un-edited nuttx_user.hex
file to produce a single combined hex file:
$ cat nuttx.hex nuttx_user.hex >combined.hex
Then use the combined.hex file with the to write the FLASH image.
If you do this a lot, you will probably want to invest a little time
to develop a tool to automate these steps.
2015-12-12 16:31:22 +01:00
module:
A simple stripped down configuration that was used for testing NuttX
OS modules. There are five
very similar NSH configurations:
- knsh. This is a somewhat simplified version of the nsh configuration
that builds using the protected build mode (CONFIG_BUILD_PROTECTED=y).
- nsh. This configuration is focused on low level, command-line
driver testing. It has no network.
- netnsh. This configuration is focused on network testing and
has only limited command support.
- module. A simple stripped down configuration that was used for testing
NuttXOS modules.
- mxtxplnd. This configuration is identical to the nsh configuration
but assumes that you have a maXTouch Xplained Pro LCD attached
and includes extra tests for the touchscreen and LCD.
2017-01-30 19:49:07 +01:00
NOTES:
1. Kernel Modules / Shared Libraries
I intend to use this configuration for testing NuttX kernel modules
in the FLAT build with the following configuration additions to the
configuration file:
CONFIG_BOARDCTL_OS_SYMTAB=y
CONFIG_EXAMPLES_MODULE=y
CONFIG_EXAMPLES_MODULE_BINDIR="/mnt/sdcard"
CONFIG_FS_ROMFS=y
CONFIG_LIBC_ARCH_ELF=y
CONFIG_MODULE=y
CONFIG_LIBC_MODLIB=y
CONFIG_MODLIB_ALIGN_LOG2=2
CONFIG_MODLIB_BUFFERINCR=32
CONFIG_MODLIB_BUFFERSIZE=128
Add the following for testing shared libraries in the FLAT
build:
CONFIG_LIBC_DLLFCN=y
CONFIG_EXAMPLES_SOTEST=y
CONFIG_EXAMPLES_SOTEST_BINDIR="/mnt/sdcard"
STATUS:
2017-01-30: Does not yet run correctly.
2017-07-02 19:04:57 +02:00
mrf24j40-starhub
This configuration implement a hub node in a 6LoWPAN start network.
It is intended for the us the mrf24j40-starpoint configuration with
the clicker2-stm32 configurations. Essentially, the SAMV71-XULT
plays the roll of the hub in the configuration and the clicker2-stm32
boards are the endpoints in the start.
NOTES:
2017-07-02 21:06:23 +02:00
1. The serial console is configured by default for use with and Arduino
serial shield (UART3). You will need to reconfigure if you will
to use a different U[S]ART.
2. This configuration derives from the netnsh configuration, but adds
2017-07-02 19:04:57 +02:00
support for IPv6, 6LoWPAN, and the MRF24J40 IEEE 802.15.4 radio.
2017-07-02 21:06:23 +02:00
3. This configuration uses the Mikroe BEE MRF24j40 click boards and
2017-07-02 19:04:57 +02:00
connects to the SAMV71-XULT using a click shield as described above.
2017-07-02 21:06:23 +02:00
4. You must must have also have at least two clicker2-stm32 boards each
2017-07-02 19:04:57 +02:00
with an MRF24J40 BEE click board in order to run these tests.
2017-07-02 22:25:51 +02:00
5. The network initialization thread is NOT enabled. As a result, the
startup will hang if the Ethernet cable is not plugged in. For more
information, see the paragraphs above entitled "Network Initialization
Thread" and "Network Monitor".
6. This configuration supports logging of debug output to a circular
buffer in RAM. This feature is discussed fully in this Wiki page:
http://nuttx.org/doku.php?id=wiki:howtos:syslog . Relevant
configuration settings are summarized below:
Device Drivers:
CONFIG_RAMLOG=y : Enable the RAM-based logging feature.
CONFIG_RAMLOG_CONSOLE=n : (We don't use the RAMLOG console)
CONFIG_RAMLOG_SYSLOG=y : This enables the RAM-based logger as the
system logger.
CONFIG_RAMLOG_NONBLOCKING=y : Needs to be non-blocking for dmesg
CONFIG_RAMLOG_BUFSIZE=8192 : Buffer size is 8KiB
NOTE: This RAMLOG feature is really only of value if debug output
is enabled. But, by default, no debug output is disabled in this
configuration. Therefore, there is no logic that will add anything
to the RAM buffer. This feature is configured and in place only
to support any future debugging needs that you may have.
If you don't plan on using the debug features, then by all means
disable this feature and save 8KiB of RAM!
NOTE: There is an issue with capturing data in the RAMLOG: If
the system crashes, all of the crash dump information will go into
the RAMLOG and you will be unable to access it! You can tell that
the system has crashed because (a) it will be unresponsive and (b)
the LD2 will be blinking at about 2Hz.
You can also reconfigure to use stdout for debug output be disabling
all of the CONFIG_RAMLOG* settings listed above and enabling the
following in the .config file:
CONFIG_SYSLOG_CONSOLE=y
CONFIG_SYSLOG_SERIAL_CONSOLE=y
7. Telnet: The clicker2-stm32 star point configuration supports the
2017-07-02 19:04:57 +02:00
Telnet daemon, but not the Telnet client; the star hub configuration
supports the Telnet client, but not the Telnet daemon. Therefore,
the star hub can Telnet to any point in the star, the star endpoints
cannot initiate telnet sessions.
2017-07-02 22:25:51 +02:00
8. TCP and UDP Tests: The same TCP and UDP tests as described for
the clicker2-stm32 mrf24j40-starpoint configuration are supported on
2017-07-02 19:04:57 +02:00
the star endpoints, but NOT on the star hub. Therefore, all network
testing is between endpoints with the hub acting, well, only like a
hub.
The nsh> dmesg command can be use at any time on any node to see
any debug output that you have selected.
Telenet sessions may be initiated only from the hub to a star
endpoint:
C: nsh> telnet <server-ip> <-- Runs the Telnet client
Where <server-ip> is the IP address of either the E1 or I2 endpoints.
STATUS:
2017-07-02: Configurations added. Not yet tested.
2017-07-03 20:37:37 +02:00
2017-07-03: Initial testing, appears to be working, but endpoints
fail to associate; sniffer shows that nothing sent fro the star
hub. I am thinking that there is something wrong with the
GPIO interrupt configuration so that no MRF24J40 interrupt are
being received.
2017-07-02 19:04:57 +02:00
2015-04-04 16:43:41 +02:00
mxtxplnd:
2015-03-30 23:31:53 +02:00
2015-12-12 16:31:22 +01:00
Configures the NuttShell (nsh) located at examples/nsh. There are five
2015-03-30 23:31:53 +02:00
very similar NSH configurations:
2015-11-18 18:45:01 +01:00
- knsh. This is a somewhat simplified version of the nsh configuration
that builds using the protected build mode (CONFIG_BUILD_PROTECTED=y).
2015-03-30 23:31:53 +02:00
- nsh. This configuration is focused on low level, command-line
driver testing. It has no network.
- netnsh. This configuration is focused on network testing and
has only limited command support.
2015-12-12 16:31:22 +01:00
- module. A simple stripped down configuration that was used for testing
NuttXOS modules.
2015-03-30 23:31:53 +02:00
- mxtxplnd. This configuration is identical to the nsh configuration
but assumes that you have a maXTouch Xplained Pro LCD attached
and includes extra tests for the touchscreen and LCD.
NOTES:
1. See the notes associated with the nsh configuration below. Only
differences from that configuration will be addressed here.
2. Basic touchscreen/LCD configuration settings are discussed above in
the paragraph entitled, "maXTouch Xplained Pro".
2015-04-04 16:43:41 +02:00
3. Unlike the nsh configuration, this configuration has the serial console
setup to USART0 which is available on EXT1:
----------- --- ------- -----
Connector PIO Arduino SAMV7
----------- --- ------- -----
EXT1 pin 13 PB0 RX3 RXD0
EXT1 pin 14 PB1 TX3 TXD0
----------- --- ------- -----
and also on the Arduino Communications connector (J505):
----------- --- ------- -----
Connector PIO Arduino SAMV7
----------- --- ------- -----
J505 pin 7 PB0 RX3 RXD0
J505 pin 8 PB1 TX3 TXD0
----------- --- ------- -----
Use of either the EXT1 or the LCD/EXT4 connectors conflict with the
Arduino RXD pin (UART3, PD28). You cannot put the maXTouch Xplained
in EXT1 or LCD/EXT4 and also use the Arduino RXD/TXD pins as your
serial console.
2015-04-04 22:05:42 +02:00
The LCD (EXT4) is configured by default because only the parallel LCD
2015-04-04 16:43:41 +02:00
interface is currently supported and that is only available on that
connector.
If you plan to use EXT2 for some reason, you may re-configure the
serial console to use UART3, the standard Arduino RXD/TXD. You
would also, of course, have to disable the LCD.
NOTE that the USART0 pins PB0 and PB1 conflict with SSC TF and TK
pins as connected to the WM8904 audio CODEC. So, unless yet a
different U[S]ART option is selected, Audio cannot be used with
this configuration.
2015-04-04 04:12:30 +02:00
2015-04-05 03:04:54 +02:00
4. SDRAM is NOT enabled in this configuration.
5. Support for the ILI8488 LCD is enabled. Only the parallel mode is
2015-04-04 22:05:42 +02:00
supported at present. As a consequence, the maXTouch Xplained Pro
must be connected at the LCD (EXT4) connector. This mode requires:
2015-04-04 04:12:30 +02:00
CONFIG_SAMV71XULT_MXTXPLND_LCD=y : Must be connect in LCD (EXT4)
CONFIG_SAMV7_SMC=y : SMC/EBI support
CONFIG_SAMV7_XDMAC=y : XDMAC support
2015-04-05 03:04:54 +02:00
6. The appx/examples/nxlines is enabled as a built-in application.
2015-04-05 17:51:38 +02:00
This is a test that displays some simple graphis and can be
executed from the NSH command line like:
nsh> nxlines
2015-03-30 23:31:53 +02:00
2015-04-05 03:04:54 +02:00
7. When the maXTouch Xplained is connected (in any position), a new I2C
2015-04-04 04:12:30 +02:00
address appears at address 0x4a:
2015-03-30 23:31:53 +02:00
nsh> i2c dev 3 77
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- 1a -- -- -- -- --
20: -- -- -- -- -- -- -- -- 28 -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- 4a -- -- -- 4e --
50: -- -- -- -- -- -- -- 57 -- -- -- -- -- -- -- 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
This is the I2C address of the maXTouch touchscreen controller.
(0x1a is the address of the WM8904 Audio CODEC, 0x28 is the
2015-04-04 04:12:30 +02:00
address of TWI interface to the EDBG, 0x4e is the address of the
CP2100CP programmable PLL, and 0x57 and 0x5f are the addresses of
the AT2 EEPROM. I am not sure what the other address, 0x37, is).
2015-03-30 23:31:53 +02:00
2015-04-05 15:22:46 +02:00
8. Support for the touchscreen test is enabled (see apps/examples/touchscreen),
however, the maXTouch is not yet working (see STATUS below).
2015-03-31 17:01:38 +02:00
STATUS:
2015-04-05 15:22:46 +02:00
2015-04-05: Partial support for the maXTouch Xplained Pro LCD is in
place. The ILI9488-based LCD is working well with a SMC DMA-based
interface. Very nice performance.
2015-05-13 01:59:45 +02:00
2015-05-12: After some difficulties, the maXTouch touchscreen
controller is now fully functional as well.
2015-03-31 17:01:38 +02:00
2015-03-30 23:31:53 +02:00
netnsh:
2015-03-10 02:58:59 +01:00
2015-12-12 16:31:22 +01:00
Configures the NuttShell (nsh) located at examples/nsh. There are five
2015-03-30 23:31:53 +02:00
very similar NSH configurations:
2015-03-27 21:18:13 +01:00
2015-11-18 18:45:01 +01:00
- knsh. This is a somewhat simplified version of the nsh configuration
that builds using the protected build mode (CONFIG_BUILD_PROTECTED=y).
2015-03-27 21:18:13 +01:00
- nsh. This configuration is focused on low level, command-line
2015-03-30 23:31:53 +02:00
driver testing. It has no network.
2015-03-27 21:18:13 +01:00
- netnsh. This configuration is focused on network testing and
has only limited command support.
2015-12-12 16:31:22 +01:00
- module. A simple stripped down configuration that was used for testing
NuttXOS modules.
2015-03-30 23:31:53 +02:00
- mxtxplnd. This configuration is identical to the nsh configuration
but assumes that you have a maXTouch Xplained Pro LCD attached
and includes extra tests for the touchscreen and LCD.
2015-03-27 21:18:13 +01:00
NOTES:
1. The serial console is configured by default for use with and Arduino
serial shield (UART3). You will need to reconfigure if you will
to use a different U[S]ART.
2. Default stack sizes are large and should really be tuned to reduce
the RAM footprint:
2015-03-30 15:33:48 +02:00
CONFIG_SCHED_HPWORKSTACKSIZE=2048
2015-03-27 21:18:13 +01:00
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
2015-03-30 15:33:48 +02:00
CONFIG_PTHREAD_STACK_MIN=256
2015-03-27 21:18:13 +01:00
CONFIG_PTHREAD_STACK_DEFAULT=2048
2015-03-30 15:33:48 +02:00
CONFIG_POSIX_SPAWN_PROXY_STACKSIZE=1024
CONFIG_TASK_SPAWN_DEFAULT_STACKSIZE=2048
CONFIG_BUILTIN_PROXY_STACKSIZE=1024
CONFIG_NSH_TELNETD_DAEMONSTACKSIZE=2048
CONFIG_NSH_TELNETD_CLIENTSTACKSIZE=2048
2015-03-27 21:18:13 +01:00
2015-03-30 15:33:48 +02:00
3. NSH built-in applications are supported. There are, however, not
enabled built-in applications.
2015-03-27 21:18:13 +01:00
Binary Formats:
CONFIG_BUILTIN=y : Enable support for built-in programs
Application Configuration:
CONFIG_NSH_BUILTIN_APPS=y : Enable starting apps from NSH command line
2015-09-25 18:14:40 +02:00
4. The network initialization thread and the NSH network montior are
enabled in this configuration. As a result, networking initialization
is performed asynchronously with NSH bring-up. For more information,
see the paragraphs above entitled "Network Initialization Thread" and
"Network Monitor".
2015-03-27 21:18:13 +01:00
5. SDRAM is NOT enabled in this configuration.
6. TWI/I2C
TWIHS0 is enabled in this configuration. The SAM V71 Xplained Ultra
supports two devices on the one on-board I2C device on the TWIHS0 bus:
(1) The AT24MAC402 serial EEPROM described above and (2) the Wolfson
WM8904 audio CODEC. This device contains a MAC address for use with
the Ethernet interface.
Relevant configuration settings:
CONFIG_SAMV7_TWIHS0=y
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
CONFIG_I2C=y
7. TWIHS0 is used to support 256 byte non-volatile storage. This EEPROM
holds the assigned MAC address which is necessary for networking. The
2015-03-28 16:42:45 +01:00
EEPROM is also available for storage of configuration data using the
2015-03-27 21:18:13 +01:00
MTD configuration as described above under the heading, "MTD
Configuration Data".
8. Support for HSMCI is built-in by default. The SAMV71-XULT provides
one full-size SD memory card slot. Refer to the section entitled
"SD card" for configuration-related information.
See "Open Issues" above for issues related to HSMCI.
The auto-mounter is not enabled. See the section above entitled
"Auto-Mounter".
9. Performance-related Configuration settings:
CONFIG_ARMV7M_ICACHE=y : Instruction cache is enabled
CONFIG_ARMV7M_DCACHE=y : Data cache is enabled
2015-03-30 15:33:48 +02:00
CONFIG_ARMV7M_DCACHE_WRITETHROUGH=y : Write through mode
2015-03-27 21:18:13 +01:00
CONFIG_ARCH_FPU=y : H/W floating point support is enabled
CONFIG_ARCH_DPFPU=y : 64-bit H/W floating point support is enabled
# CONFIG_ARMV7M_ITCM is not set : Support not yet in place
# CONFIG_ARMV7M_DTCM is not set : Support not yet in place
2015-03-30 15:33:48 +02:00
I- and D-Caches are enabled but the D-Cache must be enabled in write-
through mode. This is to work around issues with the RX and TX
descriptors with are 8-bytes in size. But the D-Cache cache line
size is 32-bytes. That means that you cannot reload, clean or
invalidate a descriptor without also effecting three neighboring
descriptors. Setting write through mode eliminates the need for
cleaning the D-Cache. If only reloading and invalidating are done,
then there is no problem.
2015-03-27 21:18:13 +01:00
Stack sizes are also large to simplify the bring-up and should be
tuned for better memory usages.
2015-03-28 21:54:30 +01:00
STATUS:
2015-03-30 15:33:48 +02:00
2015-03-29: I- and D-caches are currently enabled, but as noted
above, the D-Cache must be enabled in write-through mode. Also -Os
optimization is not being used (-O2). If the cache is enabled in
Write-Back mode or if higher levels of optimization are enabled, then
there are failures when trying to ping the target from a host.
2015-03-28 21:54:30 +01:00
2015-03-27 21:18:13 +01:00
nsh:
2015-12-12 16:31:22 +01:00
Configures the NuttShell (nsh) located at examples/nsh. There are five
2015-03-30 23:31:53 +02:00
very similar NSH configurations:
2015-03-27 21:18:13 +01:00
2015-11-18 18:45:01 +01:00
- knsh. This is a somewhat simplified version of the nsh configuration
that builds using the protected build mode (CONFIG_BUILD_PROTECTED=y).
2015-03-27 21:18:13 +01:00
- nsh. This configuration is focused on low level, command-line
2015-03-30 23:31:53 +02:00
driver testing. It has no network.
2015-03-27 21:18:13 +01:00
- netnsh. This configuration is focused on network testing and
has only limited command support.
2015-12-12 16:31:22 +01:00
- module. A simple stripped down configuration that was used for testing
NuttXOS modules.
2015-03-30 23:31:53 +02:00
- mxtxplnd. This configuration is identical to the nsh configuration
but assumes that you have a maXTouch Xplained Pro LCD attached
and includes extra tests for the touchscreen and LCD.
2015-03-27 21:18:13 +01:00
2015-03-10 02:58:59 +01:00
NOTES:
2015-03-10 16:42:35 +01:00
1. The serial console is configured by default for use with and Arduino
serial shield (UART3). You will need to reconfigure if you will
to use a different U[S]ART.
2. Default stack sizes are large and should really be tuned to reduce
2015-03-10 02:58:59 +01:00
the RAM footprint:
CONFIG_ARCH_INTERRUPTSTACK=2048
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
CONFIG_PTHREAD_STACK_DEFAULT=2048
... and others ...
2015-03-10 16:42:35 +01:00
3. NSH built-in applications are supported.
2015-03-10 02:58:59 +01:00
Binary Formats:
2015-03-11 21:41:58 +01:00
CONFIG_BUILTIN=y : Enable support for built-in programs
2015-03-10 02:58:59 +01:00
Application Configuration:
2015-03-11 21:41:58 +01:00
CONFIG_NSH_BUILTIN_APPS=y : Enable starting apps from NSH command line
2015-04-05 03:04:54 +02:00
4. SDRAM is enabled in this configuration. Here are the relevant
configuration settings:
2015-03-14 20:27:00 +01:00
System Type
CONFIG_SAMV7_SDRAMC=y
CONFIG_SAMV7_SDRAMSIZE=2097152
2015-04-05 03:04:54 +02:00
SDRAM is not added to the heap in this configuration. To do that
you would need to set CONFIG_SAMV7_SDRAMHEAP=y and CONFIG_MM_REGIONS=2.
Instead, the SDRAM is set up so that is can be used with a destructive
RAM test enabled with this option:
2015-03-14 20:27:00 +01:00
Application Configuration:
CONFIG_SYSTEM_RAMTEST=y
The RAM test can be executed as follows:
2015-04-05 02:09:10 +02:00
nsh> ramtest -w 70000000 2097152
2015-04-05 03:04:54 +02:00
NuttShell (NSH) NuttX-7.8
nsh> ramtest -w 70000000 2097152
RAMTest: Marching ones: 70000000 2097152
RAMTest: Marching zeroes: 70000000 2097152
RAMTest: Pattern test: 70000000 2097152 55555555 aaaaaaaa
RAMTest: Pattern test: 70000000 2097152 66666666 99999999
RAMTest: Pattern test: 70000000 2097152 33333333 cccccccc
RAMTest: Address-in-address test: 70000000 2097152
nsh>
2016-11-22 16:03:50 +01:00
5. TWI/I2C
2015-03-12 19:27:06 +01:00
TWIHS0 is enabled in this configuration. The SAM V71 Xplained Ultra
supports two devices on the one on-board I2C device on the TWIHS0 bus:
(1) The AT24MAC402 serial EEPROM described above and (2) the Wolfson
WM8904 audio CODEC. This device contains a MAC address for use with
the Ethernet interface.
In this configuration, the I2C tool at apps/system/i2ctool is
enabled. This tools supports interactive access to I2C devices on
the enabled TWIHS bus. Relevant configuration settings:
CONFIG_SAMV7_TWIHS0=y
CONFIG_SAMV7_TWIHS0_FREQUENCY=100000
CONFIG_I2C=y
CONFIG_SYSTEM_I2CTOOL=y
CONFIG_I2CTOOL_MINBUS=0
CONFIG_I2CTOOL_MAXBUS=0
CONFIG_I2CTOOL_MINADDR=0x03
CONFIG_I2CTOOL_MAXADDR=0x77
CONFIG_I2CTOOL_MAXREGADDR=0xff
CONFIG_I2CTOOL_DEFFREQ=400000
Example usage:
nsh> i2c
Usage: i2c <cmd> [arguments]
Where <cmd> is one of:
Show help : ?
List busses : bus
List devices : dev [OPTIONS] <first> <last>
Read register : get [OPTIONS] [<repititions>]
Show help : help
Write register: set [OPTIONS] <value> [<repititions>]
Verify access : verf [OPTIONS] [<value>] [<repititions>]
Where common "sticky" OPTIONS include:
[-a addr] is the I2C device address (hex). Default: 03 Current: 03
[-b bus] is the I2C bus number (decimal). Default: 0 Current: 0
[-r regaddr] is the I2C device register address (hex). Default: 00 Current: 00
[-w width] is the data width (8 or 16 decimal). Default: 8 Current: 8
[-s|n], send/don't send start between command and data. Default: -n Current: -n
[-i|j], Auto increment|don't increment regaddr on repititions. Default: NO Current: NO
[-f freq] I2C frequency. Default: 400000 Current: 400000
NOTES:
o An environment variable like $PATH may be used for any argument.
o Arguments are "sticky". For example, once the I2C address is
specified, that address will be re-used until it is changed.
WARNING:
o The I2C dev command may have bad side effects on your I2C devices.
Use only at your own risk.
nsh> i2c bus
BUS EXISTS?
Bus 0: YES
nsh> i2c dev 3 77
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- 1a -- -- -- -- --
20: -- -- -- -- -- -- -- -- 28 -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- 4e --
50: -- -- -- -- -- -- -- 57 -- -- -- -- -- -- -- 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
nsh>
2015-03-30 23:31:53 +02:00
Where 0x1a is the address of the WM8904 Audio CODEC, 0x28 is the
2015-03-18 00:10:44 +01:00
address of TWI interface to the EDBG, 0x4e is the address of the
CP2100CP programmable PLL, and 0x57 and 0x5f are the addresses of
2015-03-30 23:31:53 +02:00
the AT2 EEPROM (I am not sure what the other address, 0x37, is
2015-03-18 00:10:44 +01:00
as this writing).
2015-03-12 19:27:06 +01:00
2016-11-22 16:03:50 +01:00
6. TWIHS0 is also used to support 256 byte non-volatile storage for
2015-03-19 21:53:05 +01:00
configuration data using the MTD configuration as described above
under the heading, "MTD Configuration Data".
2016-11-22 16:03:50 +01:00
7. Support for HSMCI is built-in by default. The SAMV71-XULT provides
2015-03-15 19:17:39 +01:00
one full-size SD memory card slot. Refer to the section entitled
"SD card" for configuration-related information.
See "Open Issues" above for issues related to HSMCI.
The auto-mounter is not enabled. See the section above entitled
"Auto-Mounter".
2016-11-22 16:03:50 +01:00
8. Performance-related Configuration settings:
2015-03-10 16:42:35 +01:00
2015-03-11 18:23:19 +01:00
CONFIG_ARMV7M_ICACHE=y : Instruction cache is enabled
CONFIG_ARMV7M_DCACHE=y : Data cache is enabled
2015-04-05 03:58:31 +02:00
CONFIG_ARMV7M_DCACHE_WRITETHROUGH=n : Write back mode
2015-03-11 19:32:00 +01:00
CONFIG_ARCH_FPU=y : H/W floating point support is enabled
CONFIG_ARCH_DPFPU=y : 64-bit H/W floating point support is enabled
2015-03-11 21:41:58 +01:00
2015-03-10 16:42:35 +01:00
# CONFIG_ARMV7M_ITCM is not set : Support not yet in place
# CONFIG_ARMV7M_DTCM is not set : Support not yet in place
2015-03-27 17:47:03 +01:00
Stack sizes are also large to simplify the bring-up and should be
tuned for better memory usages.
2015-03-28 21:54:30 +01:00
STATUS:
2015-03-28: HSMCI TX DMA is disabled. There are some issues with the TX
DMA that need to be corrected.
2015-05-13 02:57:30 +02:00
nxwm:
This is a special configuration setup for the NxWM window manager
UnitTest. It provides an interactive windowing experience with the
maXTouch Xplained Pro LCD.
2015-05-13 19:47:47 +02:00
NOTES:
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
1. The NxWM window manager is a tiny window manager tailored for use
with smaller LCDs. It supports a task, a start window, and
multiple application windows with toolbars. However, to make the
best use of the visible LCD space, only one application window is
visible at at time.
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
The NxWM window manager can be found here:
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
NxWidgets/nxwm
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
The NxWM unit test can be found at:
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
NxWidgets/UnitTests/nxwm
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
Documentation for installing the NxWM unit test can be found here:
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
NxWidgets/UnitTests/README.txt
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
2. Here is the quick summary of the build steps. These steps assume
2016-04-23 16:21:15 +02:00
that you have the entire NuttX GIT in some directory HOME. You may
have these components installed elsewhere. In that case, you
2015-05-13 19:47:47 +02:00
will need to adjust all of the paths in the following accordingly:
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
a. Install the VNC nxwm configuration
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
$ cd HOME/nuttx/tools
$ ./configure.sh samv71-xult/vnc
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
b. Make the build context (only)
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
$ cd ..
$ make context
...
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
c. Install the nxwm unit test
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
$ cd HOME/NxWidgets
$ tools/install.sh HOME/apps nxwm
2015-05-13 19:47:47 +02:00
Creating symbolic link
2016-04-23 16:21:15 +02:00
- To HOME/NxWidgets/UnitTests/nxwm
- At HOME/apps/external
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
d. Build the NxWidgets library
2015-05-13 02:57:30 +02:00
2016-04-23 16:21:15 +02:00
$ cd HOME/NxWidgets/libnxwidgets
$ make TOPDIR=HOME/nuttx
2015-05-13 19:47:47 +02:00
...
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
e. Build the NxWM library
2016-04-23 16:21:15 +02:00
$ cd HOME/NxWidgets/nxwm
$ make TOPDIR=HOME/nuttx
2015-05-13 19:47:47 +02:00
...
f. Built NuttX with the installed unit test as the application
2016-04-23 16:21:15 +02:00
$ cd HOME/nuttx
2015-05-13 19:47:47 +02:00
$ make
3. Reading from the LCD is not currently functional. The following
settings are in the configuration that tell the system that this
is a read-only LCD:
CONFIG_LCD_NOGETRUN=y
CONFIG_NX_WRITEONLY=y
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
4. Small Icons are selected and can be very difficult to touch. You
might want to enable larger icons with:
2015-05-13 02:57:30 +02:00
2015-05-13 19:47:47 +02:00
CONFIG_NXWM_LARGE_ICONS=y
2015-05-13 18:38:54 +02:00
STATUS:
2015-05-13:
2015-05-13 21:30:26 +02:00
- The demo functions and produces displays but is not yet very stable.
- I have two maXTouch Xplained Pro displays. One works well, the
other has some issues which I suspect are due to the ribbon cable
connector with fits too snugly on one side.
2015-05-13 19:47:47 +02:00
Here are the symptoms of the LCD that does not work. I attribute
these problems with problems in the parallel interface due to a
bad connection:
- The color is wrong; to reddish. This suggests some issue with color
format or pixel width
- Images are positioned correctly on the display, but all half the
horizontal width that they should be, again suggesting some problem
with the pixel with.
- Some images are simply truncated to half the correct size (such as
the touch circles in the calibration screen).
- Other images are horizontally compressed (such as the initial NX
logo on the background).
- As mentioned above, reading fromthe LCD is not currently functional.
There are some special settings work work around this but the
bottom line is that transparent operations cannot yet be supported.
- I am seeing some small artifacts with the font used in the HEX
calculator display.
- Line spacing in the NxTerm window is too much. This is probably
a font-related issue too.
2015-08-21 20:32:34 +02:00
2016-04-18 20:25:23 +02:00
vnc:
This is a special version of an NSH configuration. It has networking
and graphics enabled. It is configured to use the VNC server to provide
a remote desktop for use with VNC client on a PC. It includes the
graphics text at apps/examples/nximage.
NOTES:
2016-04-19 23:39:58 +02:00
1. Network configuration: IP address 10.0.0.2. The is easily changed
2016-04-18 20:25:23 +02:00
via 'make menuconfig'. The VNC server address is 10.0.0.2:5900.
2016-04-22 16:57:42 +02:00
2. The default (local) framebuffer configuration is 320x240 with 8-bit
2016-04-18 20:25:23 +02:00
RGB color.
2016-04-20 17:47:02 +02:00
3. There are complicated interactions between VNC and the network
configuration. The CONFIG_VNCSERVER_UPDATE_BUFSIZE determines the
size of update messages. That is 1024 bytes in that configuration
(the full message with the header will be a little larger). The
MTU (CONFIG_NET_ETH_MTU) is set to 590 so that a full update will
2016-04-22 00:15:56 +02:00
require several packets.
2016-04-20 17:47:02 +02:00
Write buffering also effects network performance. This will break
up the large updates into small (196 byte) groups. When we run out
of read-ahead buffers, then partial updates may be sent causing a
loss of synchronization.
4. Hint: If you are debugging using the RealVNC clint, turn off all
mouse/keyboard inputs in the options/input menu. That will make
things a little clearer.
2016-04-22 16:57:42 +02:00
5. To select 16-bits per pixel RGB15 5:6:5
CONFIG_NX_DISABLE_8BPP=y
# CONFIG_NX_DISABLE_16BPP is not set
# CONFIG_VNCSERVER_COLORFMT_RGB8 is not set
CONFIG_VNCSERVER_COLORFMT_RGB16=y
CONFIG_EXAMPLES_NXIMAGE_BPP=16
2016-04-22 18:13:53 +02:00
To re-select 8-bits per pixel RGB8 3:3:2
2016-04-22 16:57:42 +02:00
# CONFIG_NX_DISABLE_8BPP is not set
CONFIG_NX_DISABLE_16BPP=y
CONFIG_VNCSERVER_COLORFMT_RGB8=y
# CONFIG_VNCSERVER_COLORFMT_RGB16 is not set
# CONFIG_EXAMPLES_NXIMAGE_GREYSCALE is not set
CONFIG_EXAMPLES_NXIMAGE_BPP=8
2016-04-22 00:15:56 +02:00
STATUS:
2016-04-22 16:57:42 +02:00
2016-04-21: I have gotten the apps/examples/nximage to work with
2016-04-22 18:13:53 +02:00
lots issues with 16-bit RGB and verbose GRAPHICS and UPDATER debug
ON. There are reliability problems and it hangs at the end of the
2016-04-23 18:21:49 +02:00
test.
2016-04-22 00:15:56 +02:00
2016-04-23 18:21:49 +02:00
2016-04-22: The default configuration now uses RGB8 which needs a lot
less SRAM for the local frame buffer and does not degrade the color
2016-04-22 18:13:53 +02:00
quality in the remote display (since it is also 8 BPP). At 8
BPP, the remote display is correct even with both GRAPHICS and
UPDATER debug OFF -- and there is no hang!
2016-04-23 16:21:15 +02:00
2016-04-23 18:21:49 +02:00
2106-04-23: The NxImage test was selected because it is a very simple
graphics test. Continued testing, however, requires a more complex
configuration. Hence, the vnxwm configuration was created.
2017-06-28 21:18:41 +02:00
2016-04-23 18:21:49 +02:00
A memory clobber error was fixed and this probably corrects some of
the reliability problems noted on 2016-04-21.
2016-04-23 16:21:15 +02:00
vnxwm:
This is a special configuration setup for the NxWM window manager
UnitTest. It provides an interactive windowing experience via a remote
VNC client window running on your PC. The SAMV71-XULT is connected to
the PC via Ethernet.
NOTES:
1. The NxWM window manager is a tiny window manager tailored for use
with smaller LCDs. It supports a task, a start window, and
multiple application windows with toolbars. However, to make the
best use of the visible LCD space, only one application window is
visible at at time.
The NxWM window manager can be found here:
NxWidgets/nxwm
The NxWM unit test can be found at:
NxWidgets/UnitTests/nxwm
Documentation for installing the NxWM unit test can be found here:
NxWidgets/UnitTests/README.txt
2. Here is the quick summary of the build steps. These steps assume
that you have the entire NuttX GIT in some directory HOME. You may
have these components installed elsewhere. In that case, you
will need to adjust all of the paths in the following accordingly:
a. Install the nxwm configuration
$ cd HOME/nuttx/tools
$ ./configure.sh samv71-xult/nxwm
b. Make the build context (only)
$ cd ..
$ make context
...
c. Install the nxwm unit test
$ cd HOME/NxWidgets
$ tools/install.sh HOME/apps nxwm
Creating symbolic link
- To HOME/NxWidgets/UnitTests/nxwm
- At HOME/apps/external
d. Build the NxWidgets library
$ cd HOME/NxWidgets/libnxwidgets
$ make TOPDIR=HOME/nuttx
...
e. Build the NxWM library
$ cd HOME/NxWidgets/nxwm
$ make TOPDIR=HOME/nuttx
...
f. Built NuttX with the installed unit test as the application
$ cd HOME/nuttx
$ make
3. Network configuration: IP address 10.0.0.2. The is easily changed
via 'make menuconfig'. The VNC server address is 10.0.0.2:5900.
4. The default (local) framebuffer configuration is 320x240 with 8-bit
RGB color.
I had some problems at 16-bits per pixle (see STATUS below). To
select 16-bits per pixel RGB15 5:6:5
CONFIG_NX_DISABLE_8BPP=y
# CONFIG_NX_DISABLE_16BPP is not set
# CONFIG_VNCSERVER_COLORFMT_RGB8 is not set
CONFIG_VNCSERVER_COLORFMT_RGB16=y
CONFIG_EXAMPLES_NXIMAGE_BPP=16
To re-select 8-bits per pixel RGB8 3:3:2
# CONFIG_NX_DISABLE_8BPP is not set
CONFIG_NX_DISABLE_16BPP=y
CONFIG_VNCSERVER_COLORFMT_RGB8=y
# CONFIG_VNCSERVER_COLORFMT_RGB16 is not set
# CONFIG_EXAMPLES_NXIMAGE_GREYSCALE is not set
CONFIG_EXAMPLES_NXIMAGE_BPP=8
5. There are complicated interactions between VNC and the network
configuration. The CONFIG_VNCSERVER_UPDATE_BUFSIZE determines the
size of update messages. That is 1024 bytes in that configuration
(the full message with the header will be a little larger). The
MTU (CONFIG_NET_ETH_MTU) is set to 590 so that a full update will
require several packets.
Write buffering also effects network performance. This will break
up the large updates into small (196 byte) groups. When we run out
of read-ahead buffers, then partial updates may be sent causing a
loss of synchronization.
STATUS:
2106-04-23: Configuration created. See status up to this data in
the vnc configuration. That probably all applies here as well.
2016-04-23 22:27:32 +02:00
Only some initial testing has been performed: The configuration
is partially functional. Menus do appear and mouse input is
probably working correctly.
But there are a lot of instabilities. I see assertions of
various kinds and the RealVNC client often crashes as well.
Some of the assertions I see are:
2016-04-23 21:26:52 +02:00
while (sem_wait(&session->queuesem) < 0)
...
rect = (FAR struct vnc_fbupdate_s *)sq_remfirst(&session->updqueue);
DEBUGASSERT(rect != NULL);
2017-01-30 19:49:07 +01:00
I would think that could mean only that the semaphore counting is
out of sync with the number of updates in the queue.
But also the assertion at devif/devif_iobsend.c line: 102 which
probably means some kind of memory corruption.
2016-04-23 21:26:52 +02:00
2017-01-30 19:49:07 +01:00
2017-01-30: knsh configuration does not yet run correctly.
