This commit modifies the existing serial driver to add support for the remaining UARTs on the BL808. It also introduces support for setting baud rate, character length, stop bits, parity, flow control and which serial port acts as the console.
Use `nxsched_gettid` instead of `nxsched_getpid`. Previously each
kernel thread was modelled as a task, so the pid is the same of the
kthread id. Now, with shared kthread group (introduced by #12320),
the pid of all kthreads will be 0 by design in shared group.
- `g_iob_sem.semcount` must be equal to the total number of free IOBs.
It can also be negative if there are no free IOBs and there are threads
waiting for an IOB.
- g_throttle_sem.semcount represents the number of IOBs available for
throttled IOB allocations. Like any other semaphore, it should only go
negative if there is a thread waiting for it.
- Both semaphores are related to the same resource (free IOBs), hence,
they must be incremented/decremented simultaneously:
- Whenever a IOB buffer is freed, if a thread is waiting for a
non-throttled IOB or a thread is waiting for a throttled IOB and we
have at least `CONFIG_IOB_THROTTLE` buffers available, the IOB is put
in the committed list (`g_iob_committed`). Otherwise, it is put in the
common free list (`g_iob_freelist`).
- `g_iob_sem` is always incremented when an IOB buffer is freed, but
`g_throttle_sem` is incremented only if we have at least CONFIG_IOB_THROTTLE
buffers free.
- Both semaphores are posted with the schedule locked to avoid any
mismatches in the semaphores count.
- If a task is waiting for an IOB semaphore (`iob_allocwait`) is
awakened and would check the `g_iob_committed`. The highest priority
task waiting for a semaphore will be awakened first.
Kthreads can share the group data so that to reduce overheads.
This implements shared kthread group via:
- use `tcb_s` instead of `task_tcb_s` for kthreads
- use `g_kthread_group` when creating kthreads
- use stackargs to start tasks and kthreads
see pull/12320 for test logs.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Thread args have already been saved to stack after the TLS section by
nxtask_setup_stackargs. This is to retrieve it for use.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
This change implements a system for allowing the D0 core (which runs NuttX) to receive forwarded interrupts from the M0 core. This makes it possible for drivers that rely on interrupts to work with peripherals attached to the M0 core.
make possible enable pool, but disabled in system heap.
also compatible for further extra heap use/not use pool.
Now use MM_HEAP_MEMPOOL_THRESHOLD -1 to indicate pool disabled.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
cpu0 cpu1:
user_main
signest_test
sched_unlock
nxsched_merge_pending
nxsched_add_readytorun
up_cpu_pause
arm_sigdeliver
enter_critical_section
Reason:
In the SMP, cpu0 is already in the critical section and waiting for cpu1 to enter the suspended state.
However, when cpu1 executes arm_sigdeliver, it is in the irq-disabled state but not in the critical section.
At this point, cpu1 is unable to respond to interrupts and
is continuously attempting to enter the critical section, resulting in a deadlock.
Resolve:
adjust the logic, do not entering the critical section when interrupt-disabled.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
as we always want to take critical_section, and it is not long time job,
take mutex is not necessary, use spinlock_irq_save as a replace is
better, dont't have to take global critial_section in pm.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
This adds pre-allocation and dynamic allocations for sigactions.
Current behavior can be acheived by setting SIG_ALLOC_ACTIONS to
a number larger than 1.
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
As suggested in PR:12530, changed the default names of ESP32S3WROOM chips to ESP32S3WROOM1N4,
ESP32S3WROOM2N16R8, ESP32S3WROOM2N32R8, ESP32S3MINI1N8.
Also regenerated all the defconfigs for board configurations.
Added a custom ESP32S3 module for custom flash configurations.
Declared ESP32S3_PSRAM_8M variable with prompt
this_task() is a function call that involves disabling interrupts and this_cpu().
Since restore_critical_section is always called in an interrupt-disabled context,
there's no need to disable interrupts again. Therefore, to save time and achieve
the same effect, I directly call tcb = current_task(me) instead of tcb = this_task().
Signed-off-by: hujun5 <hujun5@xiaomi.com>
we can use g_cpu_lockset to determine whether we are currently in the scheduling lock,
and all accesses and modifications to g_cpu_lockset, g_cpu_irqlock, g_cpu_irqset
are in the critical section, so we can directly operate on it.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
- In some cases, an operational Ethernet MAC may have no PHY, for example
when the system has a direct RMII MAC-to-MAC link.
- New config option STM32H7_NO_PHY
- With this option, PHY-specific code in the ethernet driver is not built
- This option is inherently incompatible with autonegotiation and speed and
duplex settings must be compiled in
