This patch add support to use buttons example on raspberrypi-pico.
Note: unfortunately the raspberry-pico board doesn't have usables
buttons, then you need to add external buttons connected to GPIO16
and GPIO17.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
Purpose: make the the os crash when busyloop with interrupt disable
Follow the arm gicv2 spec, if we want to use the IRQ and FIQ
simultaneously when not using the processor Security Externsions.
We should:
1. IRQ to Group 1 and FIQ to Group 0;
2. Set CICC_CTLR.FIQEn to 1;
Then in NuttX:
1. implement the arm_decodefiq and directly crash in it;
2. provide interface to change the IRQ to FIQ, e.g. change the
watchdog IRQ to FIQ, so the watchdog can trigger even with the
interrupt disabled (up_irq_save() called);
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
Signed-off-by: ligd <liguiding1@xiaomi.com>
Current `CONFIG_PAGING` refers to an experimental implementation
to enable embedded MCUs with some limited RAM space to execute
large programs from some non-random access media.
On-demand paging should be implemented for the kernel mode with
address environment implementation enabled.
This commit adds support to autoleds and userleds for
raspberrypi-pico board. It uses the board LED connected
to GPIO 25.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
As long as the GNSS feature is not used, GNSS RAM can be used as general memory.
This memory is 640KByte total, which is lower performance than the application RAM.
It is possible to locate text, data and bss into GNSS RAM and to use as heap area.
Since there were some cases in which the current modem reset
sequence did not reset the modem, the reset was ensured by
executing power off and power on of the modem.
This change adds support for the USB Transport Layer as described
in the bluetooth spec. Isochronous endpoints are not yet supported.
Because of limitations in the NuttX bluetooth stack, only one USB
device can be used. This driver will only allow one USB dongle to
use bluetooth.
A Laird USB BT4.2 dongle (from Mouser) was used for testing:
M/N BT851 1.0 1829, FCC ID:SQGBT850
lsusb: 04b4:f901 Cypress Semiconductor Corp. CYW20704A2
The following commands were used to test from the nsh prompt:
bt bnep0 scan start
bt bnep0 scan stop
bt bnep0 scan get
bt bnep0 info
The Linux gatttool was used to connect over wireless.
With the BDAddr found by "bt bnep0 info", start gatttool using:
gatttool -b BDAddr -I
Connect to the device using:
connect
Read the device name using the GAP device name UUID:
char-read-uuid 2a00
Part of the response is:
value: 41 70 61 63 68 65 20 4e 75 74 74 58
which is the string "Apache NuttX"
Usually the startup script is placed under /etc. The contents of the etc directory
are compiled and linked with Nuttx binary in the form of romfs. After startup,
it will be mounted by Nsh.
etc is generated by the different boards, that use genromfs and xxd tools to generate
and compile it into the Nuttx, for example: boards/arm/at32/at32f437-mini/tool/mkromfs.sh
The more common method is etc image generated from the content in the corresponding
board/arch/board/board/src/etc directory, and added by Makefile for example:
boards/sim/sim/sim/src/etc.
But in kernel/protected mode, Nuttx kernel and apps are run in different privileged/
non-privileged mode or the isolated binarys, so as that nsh should use syscall to
access Nuttx kernel by exported API. In this scenario, nsh can not mount the etc image
content, because that is generated in board and as a part of Nuttx kernel.
changes:
- move etc romfs mount from nsh to Nuttx, but keep the script to parse and execute.
- move and rename the related CONFIG, move customized nsh_romfsimg.h to etc_romfs.c
in boards, and no need declaration for romfs_img/romfs_img_len.
This commit changes and updates all configurations in Nuttx arch/board as much as possible,
but if any missing, please refer to the following simple guide:
- rename CONFIG_NSH_ROMFSETC to CONFIG_ETC_ROMFS, and delete CONFIG_NSH_ARCHROMFS in defconfig
- rename the etc romfs mount configs, for example CONFIG_NSH_FATDEVNO to CONFIG_ETC_FATDEVNO
- move customized nsh_romfsimg.h to etc_romfs.c in board/arch/board/board/src and no need
declaration for romfs_img/romfs_img_len.
- delete default nsh_romfsimg.h, if ROMFSETC is enabled, should generate and compile etc_romfs.c
in board/arch/board/board/src.
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
arm-none-eabi-ld: /tools/gcc-arm-none-eabi/bin/../lib/gcc/arm-none-eabi/13.2.1/../../../../arm-none-eabi/lib/thumb/v7e-m/nofp/libsupc++.a(eh_alloc.o): in function `_GLOBAL__sub_I__ZN9__gnu_cxx9__freeresEv':
eh_alloc.cc:(.text.startup._GLOBAL__sub_I__ZN9__gnu_cxx9__freeresEv+0x12): undefined reference to `getenv'
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
1.Remove RAMLOG_OVERWRITE option and related code
2.Broadcast the readability to all reader and poller
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <david.sidrane@nscdg.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
imxrt:Kconfig fix formatting
imxrt:usbphy move IMXRT_USBPHY{1|[2]}_BASE to memory map
imxrt:lpspi Fix build breakage from adding 1170
imxrt:Finish 1170 iomux and clockconfig versioning
imxrt:Remove duplicate imxrt_clock{off|all}_lpi2c4
imxrt:pmu remove duplicate dcd non 117x header
imxrt:lpspi Fix unused var warnings
imxrt:lpi2c Fix unused var warnings
imxrt:lowputs Fix unused var warnings
imxrt:imxrt117x_dmamux fix duplicate entries
imxtr:serial Use IOMUX_PULL_{UP|DOWN} and map IOMUX V1 to them
imxrt:MPU Support the 1170
imxrt:dmamux Alias IMXRT_DMAMUX0_BASE as IMXRT_DMAMUX_BASE
imx1170:ccm Alias CCM_CCGR_DMA & CCM_CCGR_SNVS_LP for compatiblity
Author: Peter van der Perk <peter.vanderperk@nxp.com>
IMXRT7 Add LPUART 9/10/11/12 support
Author: David Sidrane <david.sidrane@nscdg.com>
imxrt:1170pinmux Add QTIMER pins
imxrt:1170pinmux Add GPT pins
imxrt:1170pinmux Add FLEXPWM pins
imxrt1170:pinmap Add GPIO_ENET_1G pinning
imxrt:enet Support ENET_1G
imxrt:periphclks rt1170 does not have canX_serial clock
imxrt:flexcan:Layer imxrt_ioctl
imxrt117x:memorymap added CAN3
imxrt:ADC support ver1 and ver2 for imxrt117x
imxrt:imxrt117x_ccm Align timer naming with other imxrt QTIMERn->TIMERn
imxrt:imxrt117x_ccm align CCM names with rt106x
imxrt:XBAR support larger number of selects needed on imxrt1170
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
FlexSPI AHB Region support, PIT rename for compatiblity
imxrt:USB Analog add VBUS_VALID_3V
FlexSPI expand prefetch registers for IMXRT117X
imxrt:Support Initialization of FlexRam without Running from OCRAM
imxrt: ocotp add UNIQUE_ID register definition
imxrt: enet use ocotp unique_id
imxrt: enet fixes for imxrt117x
imxrt: ethernet pinmux sion enable
imxrt:imxrt_periphclk_configure add memory sync
Flush the pipeline to prevent bus faults, by insuring a
peripheral is clocked before being accessed on return from
this function.
imxrt:Restructure gpioN to padmux mapping
imxrt:Add imxrt1170 daisy
imxrt: correct power modes for imxrt117x fixing hang on WFI
imxrt: imxrt117x TCM MPU config
imxrt: FlexRAM clocking DIV0 setup
imxrt: 117x periphclocks wait for status bit
imxrt: iomucx set pad settings correctly and allow reconfiguration
imxrt: enet align buffers 64-byte for optimal performance
Add DSC barriers for write-through cache support
imxrt: imxrt1170 use FlexCAN FD/ECC features
imxrt:iomuxc_ver2 (117x) SD_B1 and DISP_B1 use PULL feild not PUE/PUS
imxrt:Fix 1170 SNVS addressing
imxrt: enet set mii clock after ifdown so that phy keep working
nxstyle fixes
imxrt: preprocessor and include fixes
Fix configs
imxrt1170-evk clean defconfig
Summary:
- Fixes a linker issue in https://github.com/apache/nuttx/pull/8244 by disabling compiler optimization.
- Adjusts CONFIG_DEFAULT_TASK_STACKSIZE to 4096 to ensure proper functioning of cxxtest.
Impact:
- The changes may slightly affect performance due to disabled optimizations
but are necessary for cxxtest stability.
Testing:
- Successfully tested on QEMU-8.1.2 with arm gcc 12.3.Rel1,
confirming resolution of the linker issue and stable operation of cxxtest.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
These values are board-specific properties that must be known on the application side.
Until now, these values had to be hardcoded on the application side.
The LINUM-STM32H753BI is a board with RS485, RS232, SD Card, CAN,
SD Card, USB, Ethernet, LCD, etc.
Signed-off-by" Jorge Guzman jorge.gzm@gmail.com
ci: correction in nsh defconfig file of LINUM-STM32H753BI
- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
The STM32F401RC-RS485 is a board with RS485 support, SD Card, buttons,
leds, temperature sensor, adc and etc.
Signed-off-by: Rodrigo Sim rcsim10@gmail.com
External JLink is required to program the board, so the console via RTT
is available anyway. It is much more convenient to use than soldering the
P4 connector and working with an external UART converter.
Some SD card connectors do not have separate card detection pin. In that
case card detection has to be done on CD/DAT3 data line. This means
software (i.e. architecture level driver) has to take care of pin
configuration switching (pin has to be set as data pin in case of
transfer and as interrupt card detection pin when there is no action
on data line).
This commit adds CD/DAT3 line card detection support for SAMv7 MCU.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The class device only handles descriptor information specific to the class,
and shared descriptor information is passed through parameters and
handled by the composite driver.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
When I try to set priorities in certain programs, such as init_priority(HIGH_PRIORITY), I've noticed that during linking, there's no guarantee that the programs will be compiled in the sequence I've specified based on priority. This has led to some runtime errors in my program.
I realized that in the ld file, when initializing dynamic arrays, there's no assurance of initializing init_array.* before init_array. This has resulted in runtime errors in the program. Consequently, I've rearranged the init_array.* in the ld file of NuttX to be placed before init_array and added a SORT operation to init_array.* to ensure accurate initialization based on priorities during linking.
This patch starts to implement the ability to build Meadow.OS for the Meadow F7 board with the NuttX mainline. It will be followed by more patches, progressively enabling full Meadow.OS functionality. This configuration is a work in progress.
The Meadow.OS source code is needed to build this configuration. Meadow.OS is being open-sourced under the Apache 2.0 license. A prototype of the source code release and integration with NuttX is at https://github.com/WildernessLabs/Meadow.OS/tree/prototype
This is the second revision of this patch, as the first one (https://github.com/apache/nuttx/pull/9997) was causing build issues on NuttX CI and was reverted.
This should only impact the Meadow F7 board configurations.
No testing to be done, as the configuration is under development.
Move SCU-specific ak09912 sensor into spresense board layer.
Rename a function name to register SCU sensor driver
from ak09912_register to ak09912_scu_register.
