USART peripheral can work in SPI mode as well. This commit adds support
for such functionality. Only 1 slave device is supported by the
peripheral therefore board level does not have to ensure correct CS
setup.
The usage of the peripheral is the same as with other SPI drivers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
External JLink is required to program the board, so the console via RTT
is available anyway. It is much more convenient to use than soldering the
P4 connector and working with an external UART converter.
This implements the changes required to genreate the pdf version
of the documentation. The pdf will be generated as a build artifact
attached to the build. This is the first patch to enable this
a follow on patch to the website repo will publish the pdf to the
NuttX website.
Currently only Port UART0 is supported for Allwinner A64. This PR adds support for all UART Ports: UART1 to UART4. (Except R-UART, which is a special low-power UART)
This is required for the upcoming LTE Modem Driver (Quectel EG25-G) for PINE64 PinePhone, which uses UART3. [(Details here)](https://lupyuen.github.io/articles/lte2)
The code was adapted from the NuttX UART Driver for Allwinner A1X: [`a1x_serial.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_serial.c)
`arch/arm64/src/a64/a64_serial.c`: Added ports UART1 to UART4, based on [`a1x_serial.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_serial.c)
`arch/arm64/src/a64/a64_serial.h`: Added IRQs for UART1 to UART4. Moved UART Base Addresses to `a64_memorymap.h`
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added UART Base Addresses for UART0 to UART4
`arch/arm64/src/a64/Kconfig`: Added UART1 to UART4 to Allwinner A64 Peripheral Selection menu
`boards/arm64/a64/pinephone/configs/lcd/defconfig`, `lvgl/defconfig`, `nsh/defconfig`, `sensor/defconfig`: Fixed `UART1_SERIAL_CONSOLE` to `UART0_SERIAL_CONSOLE`
Initial documentation page for SAMv7 MCU is added. There are still
board pages to be added in the future.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Current implementation supports the trigger generation only from timer
capture on period value. This is sufficient for PWM synchronization but
may not be enough for other purposes as ADC triggering for example.
This change adds an option to generate the trigger based on a duty
cycle value.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This PR adds the existing Goodix GT9XX Touch Panel Driver to the Bringup Function for PINE64 PinePhone.
With this PR, LVGL Touchscreen Apps will respond to Touch Input on PinePhone.
### Modified Files
`boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Added GT9XX Touch Panel Driver to PinePhone Bringup Function
`boards/arm64/a64/pinephone/src/Makefile`: Added `pinephone_touch.c` to the Makefile
`include/nuttx/input/gt9xx.h`: Fixed a comment in GT9XX Touch Panel Driver
### New Files
`boards/arm64/a64/pinephone/src/pinephone_touch.c`, `pinephone_touch.h`: Register GT9XX Touch Panel Driver on PinePhone
`boards/arm64/a64/pinephone/configs/lvgl/defconfig`: Added PinePhone Board Config `lvgl` to support LVGL Touchscreen Apps
### Updated Documentation
`Documentation/platforms/arm/a64/boards/pinephone/index.rst`: Added PinePhone Board Config `lvgl` for LVGL Touchscreen Apps
This PR adds the Frame Buffer Driver for PINE64 PinePhone. With this driver, NuttX Apps will be able to use the standard Frame Buffer API to render graphics on PinePhone.
`boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Render Test Pattern after calling `up_fbinitialize()` to start the Frame Buffer Driver
`boards/arm64/a64/pinephone/src/pinephone_display.c`: Add Frame Buffer Driver
`boards/arm64/a64/pinephone/src/pinephone_display.h`: Declare new function for rendering Test Pattern
`platforms/arm/a64/boards/pinephone/index.rst`: Add Frame Buffer as supported driver for PinePhone
This PR adds the driver for Xingbangda XBD599 LCD Panel (based on Sitronix ST7703 LCD Controller) on PINE64 PinePhone. This PR also includes:
- The driver for X-Powers AXP803 Power Mgmt IC, which calls our driver for Allwinner A64's Reduced Serial Bus. The PMIC Driver is needed to power on the MIPI DSI Interface for the LCD Panel.
- A simple Display Driver that renders a Test Pattern on the LCD Display at startup. It calls our Allwinner A64 drivers for Display Engine, Timing Controller TCON0 and MIPI Display Serial Interface.
The NuttX Frame Buffer Driver will be implemented in the next PR.
`arch/arm64/src/a64/a64_de.c`, `a64_de.h`: Changed the Frame Buffer pointer to `const` for Allwinner A64 Display Engine
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for PWM, for controlling the PWM Backlight
`boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Call `fb_register()` to start the Display Driver at startup
`boards/arm64/a64/pinephone/src/Makefile`: Added LCD Driver, PMIC Driver and Display Driver to Makefile
`boards/arm64/a64/pinephone/Kconfig`: Added the Kconfig option for "PINE64 PinePhone > LCD Display" (`CONFIG_PINEPHONE_LCD`) which enables the LCD Driver, PMIC Driver and Display Driver
`boards/arm64/a64/pinephone/src/pinephone_lcd.c`, `pinephone_lcd.h`: Driver for Xingbangda XBD599 LCD Panel
`boards/arm64/a64/pinephone/src/pinephone_pmic.c`, `pinephone_pmic.h`: Driver for X-Powers AXP803 Power Mgmt IC
`boards/arm64/a64/pinephone/src/pinephone_display.c`: Simple Display Driver that renders a Test Pattern in `up_fbinitialize()`
`boards/arm64/a64/pinephone/configs/lcd/defconfig`: New PinePhone Board Configuration `pinephone:lcd` that enables the LCD Driver (`CONFIG_PINEPHONE_LCD`)
`platforms/arm/a64/boards/pinephone/index.rst`: Added PinePhone Board Configuration `pinephone:lcd` that enables the LCD Driver
This PR adds the driver for Reduced Serial Bus (RSB) on Allwinner A64 SoC. The RSB Driver will be called by the upcoming Power Mgmt IC Driver for PINE64 PinePhone, to power on the LCD Display.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > RSB" (`CONFIG_A64_RSB`), which enables the RSB Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for RSB
`arch/arm64/src/a64/Make.defs`: Added the RSB Driver to the Makefile
`arch/arm64/src/a64/a64_de.c`: Increase PLL Timeout for Allwinner A64 Display Engine
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Set PinePhone Board Config `CONFIG_BOARD_LOOPSPERMSEC` to the value computed by `calib_udelay`
`arch/arm64/src/a64/a64_rsb.c`, `a64_rsb.h`: RSB Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added RSB as supported peripheral for PinePhone
This PR adds the driver for Display Engine 2.0 on Allwinner A64 SoC. The Display Engine Driver will be called by the upcoming LCD Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > DE" (`CONFIG_A64_DE`), which enables the Display Engine Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for Display Engine
`arch/arm64/src/a64/Make.defs`: Added the Display Engine Driver to the Makefile
`boards/arm64/a64/pinephone/configs/nsh/defconfig`: Removed Scheduler Debug Info (`CONFIG_DEBUG_SCHED_INFO`) from the PinePhone Board Config, because it garbles the Console Output.
`arch/arm64/src/a64/a64_de.c`, `a64_de.h`: Display Engine Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added Display Engine as supported peripheral for PinePhone
This PR adds the driver for TCON0 (Timing Controller) on Allwinner A64 SoC. The TCON0 Driver will be used by the upcoming Display Driver for PINE64 PinePhone.
`arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > TCON0" (`CONFIG_A64_TCON0`), which enables the TCON0 Driver
`arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for TCON0
`arch/arm64/src/a64/Make.defs`: Added the TCON0 Driver to the Makefile
`arch/arm64/src/a64/a64_tcon0.c`, `a64_tcon0.h`: TCON0 Driver for Allwinner A64
`platforms/arm/a64/boards/pinephone/index.rst`: Added TCON0 as supported peripheral for PinePhone
This PR adds the driver for Allwinner A64's MIPI Display Serial Interface (DSI) and MIPI Display Physical Layer (D-PHY).
This driver will be used by the upcoming Display Driver for PINE64 PinePhone.
- `include/nuttx/crc16.h`: Added 16-bit CRC-CCITT
- `libs/libc/misc/Make.defs`: Added 16-bit CRC-CCITT to Makefile
- `arch/arm64/src/a64/Kconfig`: Added the Kconfig option for "A64 Peripheral Selection > MIPI DSI" (`CONFIG_A64_MIPI_DSI`), which enables the MIPI DSI Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: Added the Base Address for MIPI DSI
- `arch/arm64/src/a64/Make.defs`: Added the MIPI DSI Driver to the Makefile
- `libs/libc/misc/lib_crc16ccitt.c`: Compute 16-bit CRC-CCITT
- `arch/arm64/src/a64/mipi_dsi.c`, `mipi_dsi.h`: Compose MIPI DSI Packets (Long, Short, Short with Parameter)
- `arch/arm64/src/a64/a64_mipi_dsi.c`, `a64_mipi_dsi.h`: MIPI DSI Driver for Allwinner A64
- `arch/arm64/src/a64/a64_mipi_dphy.c`, `a64_mipi_dphy.h`: MIPI D-PHY Driver for Allwinner A64
- `platforms/arm/a64/boards/pinephone/index.rst`: Added MIPI DSI as supported peripheral for PinePhone
Co-Authored-By: Petro Karashchenko <petro.karashchenko@gmail.com>
This PR adds the drivers for Allwinner A64 PIO (Programmable I/O) and PinePhone LEDs (Red / Green / Blue).
The PIO Driver is based on the NuttX PIO Driver for Allwinner A10: [`arch/arm/src/a1x/a1x_pio.c`](https://github.com/apache/nuttx/blob/master/arch/arm/src/a1x/a1x_pio.c)
- `arch/arm64/src/a64/Make.defs`: Add PIO Driver to Makefile
- `boards/Kconfig`: Add `ARCH_HAVE_LEDS` to PinePhone
- `boards/arm64/a64/pinephone/src/pinephone.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_boardinit.c`: Start Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_bringup.c`: Start User LEDs
- `boards/arm64/a64/pinephone/src/Makefile`: Add LED Driver to Makefile
- `boards/arm64/a64/pinephone/configs/nsh/defconfig`: Add `CONFIG_USERLED` to `nsh` config
- `arch/arm64/src/a64/a64_pio.c`, `a64_pio.h`: Allwinner A64 PIO Driver
- `arch/arm64/src/a64/hardware/a64_memorymap.h`: PIO Memory Map
- `arch/arm64/src/a64/hardware/a64_pio.h`: PIO Definitions
- `boards/arm64/a64/pinephone/include/board.h`: Define PinePhone LEDs
- `boards/arm64/a64/pinephone/src/pinephone_autoleds.c`: Driver for Auto LEDs
- `boards/arm64/a64/pinephone/src/pinephone_userleds.c`: Driver for User LEDs
- `introduction/supported_platforms.rst`: Add Allwinner A64 as Supported Platform
- `platforms/arm/a64/boards/pinephone/index.rst`: Add PIO and LEDs to PinePhone
Config option IMXRT_ADCx_ETC can now be used to select an external HW
trigger to be used instead of continous trigger. Continous trigger is
used if IMXRT_ADCx_ETC = -1 (default option). Otherwise the source signal
is routed through XBAR and used as a trigger.
Hardware triggering is currently limited to maximum of 8 channels.
HW trigger is automatically disabled if there are more than 8 channels.
The external triggering was tested with PWM signal as a source.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit allows the PWM modules to be synchronized by an external
signal (other PWM module for example). The sync source can be selected
from configuration.
PWM module can also now generate a trigger when its timer reaches the duty
cycle. This trigger is used for the synchronization of other modules. It
can also be used for triggering ADC for example in the future.
Thanks to Rastislav Pavlanin and Jan Spurek from NXP support for
suggestion which helped to solve the inter-module PWM synchronization
task.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This patch adds corrected implementation of FLASH memory to be used
with progmem driver for use with mtd filesystems like nxffs or smartfs.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This patch adds to the nucleo-wl55jc previously implemented EXTI support.
Button support with nuttx's button driver is added.
I've written small example to show how to use GPIO EXTI. B3 button can be
used (selectable via Kconfig) to toggle Red LED.
I've added new defconfig for demo purposes. I've included there config
and enabled example programs that are meant to demonstrate functions of
the board and does not really have a place in real world project. Like
Red LED can be toggled with B3 button, or LED example that flashes LEDS,
or button example to show which button has been pressed.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- Change (1 << 0) to (1 << BUTTON1_BIT (and similar)
v2 -> v3:
- Fix invalid BUTTON3_BIT value
v3 -> v4:
Suggested by: Petro Karashchenko
- Change 0/1 to false/true
This patch implements working support for EXTI GPIO.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- change (1 << n) to (1 << (n)) in macro definition
- change 1 << X to (1 << X) in code
- fix alignment
v2 -> v3:
Suggested by: Petro Karashchenko
- I was supposed to change (1 << pin) to 1 << pin, not the other way around:)
This patch adds documentation for both stm32wl5 chip family and
nucleo-wl55jc board. I've kept the same directory structure for
arm/stm32 as in arch/ and boards/ directories.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Multiple files were badly formatted, which resulted in many
warnings. This made it harder to check for errors in newly
written documentation.
What's worse, badly formatted text resulted in butchered
output in generated html.
This patch fixes most of the errors, but alas, not all of
the errors can be fixed. Anyway, this should be way easier
to spot errors in newly written docs now.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
