Summary:
- This commit removes critical section in mm_sem.c which was
added to stabilize the NuttX SMP kernel in Mar 2018.
Impact:
- SMP only
Testing:
- Tested with ostest with the following configs
- maix-bit:smp (QEMU), esp32-devkitc:smp (QEMU)
- sabre-6quad:smp (QEMU), spresense:smp, sim:smp
- Tested with nxplayer with the following configs
- spresense:wifi_smp, spresense:rndis_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
getopt() in the FLAT build environment is not thread safe. This is because global variables that are process-specific in Unix are truly global in the FLAT build. Moving the getopt() variables into TLS resolves this issue.
No side-effects are expected other than to getopt()
Tested with sim:nsh
OpenGroup specification was updated regarding the return value for
pthread_once, which after Issue 7 states that "the [EINVAL] error for an
uninitialized pthread_once_t object is removed; this condition results
in undefined behavior".
Summary:
- In arp_wait_setup() and arp_wait_cancel(), g_arp_waiters
is protected by a critical section.
- However, I noticed that arp_notify() does not protect the
g_arp_waiters that would cause memory corruption
- This commit fixes the issue.
Impact:
- None
Testing:
- Tested with spresense:rndis_smp, spresense:rndis
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- In arp_send(), arp_wait_setup() adds a notify object to g_arp_waiters
which is removed in arp_wait() in normal case.
- However, in timeout and error cases, the object was not removed and
caused memory corruption.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with spresense:rndis_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
lpc17_40_userleds.c: Adds the support of Userleds driver which
provides a device to manipulate the 4 leds of the board through the
/dev/userleds.
lpc17_40_leds.c: Removes not used definitions, eg. MBED_LED3_ON.
Board LED Status support(CONFIG_ARCH_LED=y) and Device Drivers/Led
Support(CONFIG_ARCH_USERLED=y) can not be enable together.
Signed-off-by: Gustavo L F Walbon <gwalbon@linux.ibm.com>
Normally, statically allocated data goes in .bss, followed by the
initial stack, followed by HEAP. However, any data that is statically
allocated in SRAM4 with __attribute__ ((section (".sram4"))) will
clobber, and be clobbered by, the HEAP.
On STM32H7, BDMA can only access SRAM4. Therefore any BDMA buffers (or
any other data) placed in SRAM4 will expose this problem. In one case,
this manifested as a failure of NSH to start, because the SPI6 BDMA
buffers clobbered the /dev/console inode structs, which the OS
allocated earlier.
This PR ensures that only the rest of SRAM4, after any static data, is
added to the heap. This PR also allows SRAM4 to be completely excluded
from the heap by a new Kconfig, CONFIG_STM32H7_SRAM4EXCLUDE, similar
to what CONFIG_STM32H7_DTCMEXCLUDE does for the DTCM region.
Change required in linker scripts:
Every STM32H7 linker script must replace this:
.sram4 :
{
} > sram4
with this:
.sram4_reserve (NOLOAD) :
{
*(.sram4)
. = ALIGN(4);
_sram4_heap_start = ABSOLUTE(.);
} > sram4
or link will fail with: undefined reference to '_sram4_heap_start'.
The Release Notes should document this for users with out-of-tree
boards.
arch/arm/src/stm32h7/Kconfig:
* Add config STM32H7_SRAM4EXCLUDE to allow excluding all of SRAM4
from the HEAP.
arch/arm/src/stm32h7/stm32_allocateheap.c:
* Only when including SRAM4 in the heap, define HAVE_SRAM4,
SRAM4_START, SRAM4_END, and SRAM4_HEAP_START.
* Add "Private Data" section.
* Add extern for_sram4_heap_start, which must be defined in the
board's linker script.
* arm_addregion(): Only add SRAM4 to the heap when configured to
do so, i.e., unless CONFIG_STM32H7_SRAM4EXCLUDE is defined, and
only add the portion of SRAM4 that is past any static data.
boards/arm/stm32h7/nucleo-h743zi/scripts/flash.ld:
boards/arm/stm32h7/nucleo-h743zi/scripts/kernel.space.ld:
boards/arm/stm32h7/nucleo-h743zi2/scripts/flash.ld:
boards/arm/stm32h7/stm32h747i-disco/scripts/flash.ld:
boards/arm/stm32h7/stm32h747i-disco/scripts/kernel.space.ld:
* Update all in-tree STM32H7 board linker scripts as described in
"Change required in linker scripts" above.
Testing:
* Successfully built all of the following configurations:
nucleo-h743zi2:jumbo
nucleo-h743zi2:nsh
nucleo-h743zi:nxlines_oled
nucleo-h743zi:elf
nucleo-h743zi:otg_fs_host
nucleo-h743zi:nsh
nucleo-h743zi:netnsh
nucleo-h743zi:pwm
stm32h747i-disco:nsh
* Tested with custom board.
* nxstyle.
References:
[1] See the dev@nuttx.a.o mailing list discussion started 2021/03/25:
"How to ensure HEAP will not overlap static DMA buffer?"
https://lists.apache.org/thread.html/recf2bb9043f8c9f53c10917e2adb2ec64fe35dc5e6f9a695a7ac6ecc%40%3Cdev.nuttx.apache.org%3E
[2] See arm_addregion() in arch/arm/src/stm32h7/stm32_allocateheap.c
Thanks to Gregory Nutt and David Sidrane for suggestions and reviews.
