wireless network devices: Attach radio to d_buf before registering device to handle forwarding case.
When CONFIG_NET_IPFORWARD is enabled, and CONFIG_NET_6LOWPAN is being used, a packet that attempts to get forwarded on the 6LoWPAN interface will require that the radio's buffer be attached to d_buf. Otherwise the below exception will be hit.
~line 542 of sixlowpan_framelist.c
```
/* Recover the reassembly buffer from the driver d_buf. */
reass = (FAR struct sixlowpan_reassbuf_s *)radio->r_dev.d_buf;
DEBUGASSERT(reass != NULL);
```
The underlying "radio" in this case is the mac802154_netdev.
This behavior has probably not been observed because the buffer is normally attached in the periodic txpoll worker. However, in my case, the 6LoWPAN interace was not UP yet, and therefore the worker hadn't run yet.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154: Support dynamic FCS length. Adds IEEE802154_ATTR_PHY_FCSLEN.
This change introduces IEEE802154_ATTR_PHY_FCSLEN which the radio layer can support to set/get the FCS length that's added to the end of the frame. One use case, in promiscuous mode, is to add back in the FCS of the received frame by increasing the iob->io_len by the FCS length.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
wireless/ieee8021254: Adds support for energy detect.
Adds support for energy detect by introducing a new radio call/callback, as the PHY layer is required to perform the energy detect.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Testing of the WiFi is minimal so far but functionality is proven. I'm specifically not happy that the driver doesn't recover elegantly from a DMA data checksum failure, but that is an issue that can be dealt with in due course ... I'm trying to get the rest of the interfaces fleshed out and the hardware proven so it can go for pre-production build. I _think_ there's only Bluetooth and USB-device left to implement now.
Improve gs2200m performance
* arch/arm/src/cxd56xx: Fix dma initialization in cxd56_dmac.c
up_dma_initialize() must be used instead of up_dmainitialize()
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* drivers/wireless: Introduce CONFIG_WL_GS2200M_SPI_FREQUENCY
Also, changed usleep(100) to up_udelay(100) to avoid invalid response.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense/wifi: Improve performance for webserver
This commit changes followings.
1. Enable SPI DMA for both TX and RX
2. Increase SPI clock speed from 4MHz to 10MHz
3. Increase buffer size for sendfile() from 512B to 1KB
4. Enable sendfile() for webserver
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Fix a passive close when sending a packet in gs2200m.c
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
nrf24l01: fix PIPENO/PKTLEN bitmask in rx fifo header
In RX fifo header, the first byte should use 5 lsb to store PKTLEN
and 3 msb to store PIPENO. However, FIFO_PIPENO_SHIFT was set to 4
which causes the lsb of pipe number to interfere with the received
packet size stored in the fifo.
This fix rx corruption when using pipe number > 0.
Signed-off-by: Federico Braghiroli <federico.braghiroli@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
nrf24l01: don't block in read if file descriptor is O_NONBLOCK
nrf24l01: support for "multicast" TX mode - no waiting for ACK (needs to be enabled with fcntl SETTXPAYLOADNOACK)
Approved-by: Gregory Nutt <gnutt@nuttx.org>
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
Fixed coding standard error in several files. Use of while( is incorrect; a space is required between while and (. Also ran tools/nxstyle and fix thoses complaints as well in most files.
Changes to comply with coding standard. Mostly focused on files with missing space after keyword in if(, switch(, and for(. Offending files also got changes to comply with tools nxstyle. If there were logs of nxstyle complaints, the file also got a taste of tools/indent.sh. Still need to fix occurrences of while( with missing space. There are a lot of them.
SX127X improvements
drivers/wireless/lpwan/sx127x/sx127x: add TX power configuration
drivers/wireless/lpwan/sx127x/sx127x: discard RX packets with unsupported length
drivers/wireless/lpwan/sx127x/sx127x: refactor some logic
drivers/wireless/lpwan/Kconfig: move some hardcoded sx127x configuration to Kconfig
drivers/wireless/lpwan/Kconfig: remove EXPERIMENTAL flag
configs/b-l072z-lrwan1/sx127x: board-specific sx127x configuration
configs/nucleo-f091rc/sx127x: board-specific sx127x configuration
configs/nucleo-l073rz/sx127x: board-specific sx127x configuration
LORA and FSK look fine but there is something missing for OOK and communication is not working yet.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
arch/arm/src/stm32f0l0: SPI support for F0
arch/arm/src/stm32f0l0/Kconfig: L0 parts should select STM32F0L0_STM32L0
arch/arm/src/stm32f0l0/hardware: unify names for ADC/DAC/DMA/CAN
drivers/wireless/lpwan/sx127x/sx127x.c: return immediately when ISR0 is called but sx127x is not initialized
configs/nucleo-f091rc: support for sx127x
configs/nucleo-l073rz: cosmetics
configs/b-l072z-lrwan1/include/board.h: use HSI as default clock source and fix typo in SPI1 pins
Approved-by: GregoryN <gnutt@nuttx.org>
drivers/timers/rtc.c: Support signal notification through SIGEV_THREAD
drivers/input/ajoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/djoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/button_upper.c: Support signal notification through SIGEV_THREAD
drivers/sensors/zerocross.c: Support signal notification through SIGEV_THREAD
drivers/wireless/ieee802154: Support signal notification through SIGEV_THREAD
drivers/lcd/ft80x.c: Support signal notification through SIGEV_THREAD
sixlowpan: Fixes logic surrounding the Universal/Local bit. This bit represents whether the IID is locally/globally administered. The U/L bit is bit 1 of the MSB of the EUI-64. It should only be inverted in cases where there is a full EUI-64. In cases whe
* sixlowpan: Fixes logic surrounding the Universal/Local bit. This bit represents whether the IID is locally/globally administered. The U/L bit is bit 1 of the MSB of the EUI-64. It should only be inverted in cases where there is a full EUI-64. In cases where the IID is derived from say, a short address, this bit should be forced to 0, indicating that it is locally administered.
See:
https://tools.ietf.org/html/rfc4291#section-2.5.1https://tools.ietf.org/html/rfc4944#section-6https://tools.ietf.org/html/rfc2464#section-4
* sixlowpan: Account for endianness with U/L bit.
Approved-by: GregoryN <gnutt@nuttx.org>
Xbee getset txpwr
* drivers/wireless/ieee802154/xbee: Minor improvements to debug facilities.
* drivers/wireless/ieee802154/xbee: Add support for setting/getting tx power.
TODO: The input/output arguments from the MLME primitive are intended to be an int32_t dbm value. However this change simply reports the power level register of the XBee. Need to add look-up table to back calculate the dbm value.
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee.c
Approved-by: GregoryN <gnutt@nuttx.org>
This makes the user interface a little hostile. People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header). A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length. Instead, we define the packet buffer size then derive the MTU.
The MTU is not common currency in networking. On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP). Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes. So we should be all good and without the recurring 14 byte error in MTU's and MSS's.
Squashed commit of the following:
Trivial update to fix some spacing issues.
net/: Rename several macros containing _MTU to _PKTSIZE.
net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE. This is not the MTU which does not include the size of the link layer header. This is the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename the file d_mtu in the network driver structure to d_pktsize. That value saved there is not the MTU. The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header. The MTU does not include the link layer header.
Squashed commit of the following:
sched: Rename all use of system_t to clock_t.
syscall: Rename all use of system_t to clock_t.
net: Rename all use of system_t to clock_t.
libs: Rename all use of system_t to clock_t.
fs: Rename all use of system_t to clock_t.
drivers: Rename all use of system_t to clock_t.
arch: Rename all use of system_t to clock_t.
include: Remove definition of systime_t; rename all use of system_t to clock_t.
drivers/xbee: Fixes issue with timeouts. Timeouts were in ticks but should have been in ms. This caused false triggers of timeout causing redundant packets, etc.
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
include/nuttx/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
drivers/wireless/ieee80211: Cosmetic, coding standard changes from review of last merge.
configs/photon: Cosmetic, coding standard changes from review of last merge.
arch/arm/src/stm32: SDIO changes from last review: Fix a few long lines and other coding standard issues; Make additions for SDIO card support dependent on a configuration option.
Author: hhuysqt <hyq9606@126.com>
Return IEEE 802.11 MAC address just as ethernet does
Modifyed bcmf_board_setup_oob_irq declaration
Modified OOB ISR function types
Add some logic according to WICED SDK
Bug fixed: data_offset counts in 4-bytes
Add BCM43438 logic for future developement
Add tips on using telnet
Use SDIO in-band interrupt instead of OOB interrupt, because Photon seems to unconnect the OOB interrupt line...
add SDIO in-band interrupt logic
Xbee: Adds a timeout to send logic to handle case where XBee module fails to respond to a Transmit request with a Transmit Status
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm/src/stm32: Add Kconfig options needed by the HCI UART. Various fixes to finally get a clean error free compile with no unexpected warnings.
arch/arm/src/stm32: In HCI UART, use spin_lock_irqsave() instead of enter_critical_section() whenever possible.
arch/arm/src/stm32: In HCI UART, fix up naming of configurations so that they are unique. Still needs Kconfig settings. Modify logic so that there can be multiple HCI UARTs, some supporting DMA and some not.
arch/arm/src/stm32: Integrate watermarks and software Rx flow control into the HCI UART driver.
arch/arm/src/stm32: Eliminate some HCI UART UART configuration options. Per the HCI UART spec, the link will b 8 data bits, no parity, 1 stop bit... Always.
arch/arm/src/stm32: Trivial cleanup
arch/arm/src/stm32: Fixes most initial compilation issues STM32 HCI UART driver. Still need to set up USART configuration parmeters for HCI UART
arch/arm/src/stm32: Completes first cut at STM32 HCI UART driver.
arch/arm/src/stm32: Completes most of read logic for HCI UART. Still needs to be able to block if no read data is available. Still missing write and flush logic.
drivers/wireless: Remove txenable from HCI UART methods. arch/arm/src/stm32: Reorganize some structures in HCI UART.
arch/arm/src/stm32: Still messaging the HCI uart driver.
arch/arm/src/stm32: Some trivial renaming.
arch/arm/src/stm32: A little more HCI-UART logic.
arch/arm/src/stm32: Initial setup to support HCI-UART. Little more than the serial driver with some name changes and a few things removed.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Fix a few remaining refereces to cc3000.
Author: Alan Carvalho de Assis <acassis@gmail.com>
drivers/wireless/cc3000: emove the driver to support CC3000 because it doesn't use the USRSOCKET
Author: Alan Carvalho de Assis <acassis@gmail.com>
configs: Remove board support to CC3000 from all relevant configurations.
Author: Gregory Nutt <gnutt@nuttx.org>
configs/spark: Removes Spark board configuration. Still available in the Obsoleted repository. This is preparation for removal of CC3000 support by Alan Carvalho de Assis. If there is no CC3000 support, then there is no purpose in supporting the Spark either.
wireless/bluetooth: This completes the basic logic path that gets frames from the Bluetooth stack and into the network layer.
wireless/bluetooth: Fleshes out some of the network packet receive logic.
wireless/bluetooth: Replace buffer allocated with primitive allocator from ieee 802.15.4.
wireless/ieee802154: Fix a few typos.
wireless/bluetooth: More renaming in preparation for some real work.
wireless/bluetooth: Some trivial renaming; update comments
Squashed commit of the following:
wireless/bluetooth: Some small changes that gets to a clean compile by just eliminating some incorrect implementations (still with a lot of warnings. The logic is still incomplete but now not so lethal.
wireless/bluetooth: Restructuring: Connection interfaces should internal to wireless/bluetooth. include/nuttx/wireless/bt_conn.h removed and merged with wireless/bluetooth/bt_conn.h. Several fix to get closer to bt_netdev.c compiling. Need to design some not interfaces and use some existing interfaces to send and receiv packets.
wireless/bluetooth: Some organization with some network device compile errors fixed. Still not even close to compiling.
net/bluetooth: Fix numerous compile issues; Still open design issues with regard to the interface with the Bluetooth stack.
wireless/bluetooth: Create bt_netdev.c with a crude copy of mac802154_netdev.c. Does not not even compile yet.
include/nuttx/net: Add bluetooth.h. Content is not yet correct.
net/netpackets: Add bluetooth.h. Update net/bluetooth to use new socket address definition.
net/bluetooth: Some fixes for initial build.
net/bluetooth: Add initial support for Bluetooth sockets. The initial cut is just the a clone of the IEEE 802.15.4 socket support with name changes.
net/ieee802154: Fix some typos noted when cloning to create net/bluetooth.
Squashed commit of the following:
drivers/bluetooth: Re-architect Bluetooth UART driver to follow upper/lower half model. Completely untested.
drivers/bluetooth: Grr.. Another band-aid commit to stay in sync with master. Why is this so difficult
drivers/bluetooth: Band-aid commit to stay in sync with master. Lost it somehow.
drivers/wireless/bluetooth: A few changes, mostly thought experiments.
drivers/wireless/bluetooth: UART-based Bluetooth driver ported from the Intel/Zephyr arduino101_firmware_source-v1.tar package. This initial commit is the original files in the NuttX build environment with changes to conform with the coding standard. It should not even build.
cc1101: Changes from review of last PR.
remove gpio
remove cc1101 frame len
remove FLAGS_RXONLY flags
add cc1101 function
remove some waring
add cc1101 poll function
add cc1101 register
add cc1101 isr read data
add cc1101 spi deviceId
add cc1101 init2
add wait cc1101 chip ready
raw init cc1101
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology
* mac802154: Adds missing breaks from case statement
* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast
* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC
* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS
* xbee_netdev: Network must be locked when calling sixlowpan_input
* sixlowpan: Reassembly buffer can't be freed if provided by radio driver
* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver
* ieee802154: Adds basic logging to ieee802154_primitive.c
* Minor fixes after rebase
* xbee: Adds AT query timeout to retry if XBee doesn't respond to request
* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'
* mac802154: Removes unused function declaration
* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator
* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.
* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.
* sixlowpan: Fixes logic to correctly check if packet is large enough to include header. This would cause packets to be considered too small when they are sufficiently sized.
* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address
* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.
* configs/same70-xplained: Simple spelling fix
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Change all calls to mq_receive() and mq_timedreceive() in the OS to calls to nxmq_receive() and nxmq_timedreceive(), making appropriate changes for differences in return values.
sched/mqueue: Add nxmq_receive() and mxmq_timedreceive() which are functionally equivalent to the standard mq_receive and mq_timedreceive() except that (1) they do not create cancellation points, and (2) the do not modify the application's errno variable.
Change all calls to mq_send() and mq_timedsend() in the OS to calls to nxmq_send() and nxmq_timedsend(), making appropriate changes for differences in return values.
sched/mqueue: Add internal function nxmq_send() and nxmq_timedsend() that are equivalent to mq_send() and mq_timedsend() except that they do not create cancellation points and do to not modify the errno variable.
Replace all calls to sigqueue() in the OS proper with calls to nxsig_queue() to avoid accessing the errno variable.
sched/signal: Add nxsig_queue() which is functionally equivalent to sigqueue() except that it does not modify the errno variable.
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
configs/z80sim and xtrs: Serial driver lower halfs ioctl methods should return a negated errno value, not set the errno variable.
drivers/wireless: CC1101 driver not permitted to set errno.
drivers/sensors: LIS331DL driver not permitted to set errno.
drivers/lcd: ILI9341 initialize method not permitted to set errno,
drivers/serial: 16550 UART driver IOCTL method must not set errno; it must return a negated errno value.
drivers/xbee: Fixes a few warnings
* drivers/xbee: Fixes a few warnings
* configs/clicker2-stm32: Updates sections about i8sak usage in the README
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/wireless: Adds XBee S2C (802.15.4 firmware) support. XBee driver emulates mac802154 interface
* drivers/wireless/xbee: Adds xbee_netdev. Very similar to mac802154_netdev
* configs/same70-xplained: Starts adding support for XBee radio
* drivers/wireless/ieee802154/xbee: More structuring of XBee driver
* drivers/wireless/ieee802154/xbee: More Xbee work. Starts adding support on Clicker2
* drivers/wireless/ieee802154/xbee: More XBee MAC code
* configs/clicker2-stm32: More work to add XBee radio support
* drivers/wireless/ieee802154/xbee: Most of driver is now structured. No build errors
* configs/clicker2-stm32: Adjustments to XBee click module support
* drivers/xbee: Changes md_ prefix to xd_ prefix for xbeenet_driver_s fields
* drivers/xbee: XBee network device now passes MAC events via IOCTL
* drivers/xbee: Support querying device for parameters, setting parameters, and structures association/startpan logic
* configs/clicker2-stm32: Fixes Xbee lower half ATTN poll logic
* drivers/xbee: Removes dependce on CONFIG_IEEE802154_NETDEV
* drivers/xbee: Supports MAC RESET.request primitive
* drivers/xbee: Exposes generic AT query to the rest of driver
* drivers/xbee: Sets local values when writing setting change to Xbee device
* drivers/xbee: Finish association logic
* drivers/xbee: Adds xbee_get_mhrlen( ) allocating enough space for API frame header to frame
* drivers/xbee: Finishes transmit/receive logic
* drivers/xbee: Fixes xbee_netdev to match logic in mac802154_netdev.c
* drivers/xbee: Rearranges logic to prevent a loop condition where recursion could potentially occur to the point of deadlocking the system
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Merged in merlin17/nuttx/mac802154-sock (pull request #479)
wireless/ieee802154: Adds support for receiving MAC events via IOCTL through socket interface. Other small fixes and cleanup
* ioctl: Cleans up MAC802154IOC values
* wireless/ieee802154: Cleans up MAC802154IOC_NOTIFY_REGISTER logic in character driver
* wireless/ieee802154/mac802154_netdev: Adds support for MAC event notification via IOCTL
* wireless/ieee802154/mac802154: Changes reset logic. No longer reset extended address.
* wireless/ieee802154: Cleans up MAC802154IOC logic
Moves MAC802154IOC from ieee802154_ioctl.h and renames ieee802154_ioctl.h to ieee802154_device.h since it only contains types relevant to the MAC char device now.
* wireless/ieee802154/mac802154_device: Cleans up IOCTL logic for recent changes.
* drivers/wireless/ieee802154/mrf24j40: Adds missing break in case statement
* wireless/ieee802154/mac802154_netdev: Starts adding support for passing MAC events via IOCTL
* wireless/ieee802154/mac802154: Fixes issue with receiver enable logic
* wireless/ieee802154/mac802154: Fixes issue where extended address is cleared and not rewritten after radio reset
* configs/clicker2-stm32/mrf24j40-mac: Enables RAMLOG and wireless driver logging
* wireless/ieee802154/mac802154: Fixes poll logic meant to automatically choose address mode based on short address range.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
commit 2a3ab1652a2c95bcfc8be8380fc7cbdcb6472938
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Sat Aug 19 08:44:31 2017 -0600
PF_IEEE802154: Finish some missing bind() logic. Add configs/sim configuration for testing.
commit 59be4b846a6e3bfe82087a888e3fdac9c3c414e5
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:30:04 2017 -0600
PF_IEEE802154: More renaming to decouple 6LoPAN from radios in general.
commit 69fabb1aea76e54381bdc13de28a3f1441fb42f4
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 19:21:11 2017 -0600
PF_IEEE802154: Missed a few renamings.
commit ff0af1bb25567720934cc1c2a721ccd92cc35f89
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:46:58 2017 -0600
PF_IEEE802154: A few bugfixes
commit 01c7c84afd00cf907d280d30cfaf0fb2cf90e02e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 17:01:31 2017 -0600
PF_IEEE802154: A few bugfixes
commit dcef4056d1c1488c93151135f3b7106977faa903
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 16:31:05 2017 -0600
PF_IEEE802154: Bring in framework for sendto/recvfrom. Currently just a crude port of functions from net/pkt and do not provide the implemenation needed.
commit 68c5b7b6dd3ab7eb2d0c19890abb38e6561b140e
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:18:31 2017 -0600
Trivial fix to typo in comment
commit fd0af534c089569ccdbd59f13b85453de0a653ad
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 15:07:20 2017 -0600
PF_IEEE802154: Add device lookup logic; Rename some things that used to be used only by 6LoWPAN but now must be shared with PF_IEEE802154 and need more generic naming.
commit 4fc80a1659f1c699b050775cefc7f6b631b46114
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:49:54 2017 -0600
PF_IEEE802154: Add driver poll logic.
commit d83f71992df8764faa93f9425f1a7602a758f730
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 13:28:59 2017 -0600
PF_IEEE802154: Add frame input function.
commit 77561b8c4d5d7be1f8d8eb62cf1a07229afe2048
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 12:46:29 2017 -0600
PF_IEEE802154: Socket type should be SOCK_DGRAM. Hook in socket interface.
commit c0f90350282e9905d7f26a1b30f04cc6d6794648
Merge: 8b518abfd0 169c55e546
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:36:32 2017 -0600
Merge remote-tracking branch 'origin/master' into pf_ieee802154
commit 8b518abfd07d492f5148f2c5fdf65604de9822da
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 09:35:39 2017 -0600
PF_IEEE802154: Add initialization and connection management logic.
commit 98b62620b3cb420041d8ad14204f9410a8aace8c
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Aug 18 07:52:51 2017 -0600
PF_IEEE802154: Add basic build support and socket interface framework.
