configs: spresense: add USBDEV_SETNOTIFYSIG signal id
Set signal id for notify USB device connection status and
supply current value.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: Enable UID functionality
To enable the UID functionality for spresense board
set BOARDCTL_UNIQUEID in menuconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs/lc823450-xgevk: Remove cpu assignment for lpwork
This change will reduce audio underrun when running dvfs auto mode.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: add I2CTOOL support and extend GPIO for future use
* arch: arm: cxd56xx: add delay support
add delay support for cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: register I2C busses
for development is usefull to register I2C busses when the I2CTOOL
is built
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs:spresense: enable GPIO interface
enable GPIO interface on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: enable BMI160_I2C sensor
* drivers: sensors: add BMI160 driver
Enable driver support for the Bosch BMI160 Inertial
Measurement sensor
This driver can be used with the BMI160 sensor connected over
SPI or I2C bus
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable BMI160_I2C sensor
Enable BMI160 sensor connected over I2C on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: spresense: remove SPI MMC/SD & add ADC
* configs: spresense: remove SPI MMC/SD support
SPI MMC/SD is not used on spresense board.
A commit will follow to add support for custom boards
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable ADC support
enable ADC support for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: SCU, ADC, I2C
* nuttx: configs: spresense: LEDS: fix warnings
In the initial code several errors were missed because I pushed
the dirty code.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Sensor Control Unit (SCU)
Add Sensor Control Unit (SCU) on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add I2C support
add I2C support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add ADC interface support
Add ADC interface support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Use DMAC for reading sensing data
Use DMAC for reading sensing data from SCU on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: code style sanitization
NuttX does not use Deoxygen for documentation and no file should contain Doxygen tags or Doxygen style comments.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable I2CDEV
add enable I2CDEV for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add notification LEDs
Add usefull diagnostic LEDs on the speresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add UID support
* arch: arm: cxd56xx: add UID support
Add support to be able to read the HW UID
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable USERLEDS
add USERLED for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
commit f5080f53516a853408dd80f09f85e1d1c139133f
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 12:24:22 2019 -0600
arch/z80/src/ez80/ez80_spi.c: SPI driver still does not work. But the driver now has timeouts so that at least it does not hang the system on startup.
commit 5241e9ae643981c43c8c7fa8478a01d0c2e17eb0
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 10:45:11 2019 -0600
arch/z80/src/ez80: Fixes to SPI baud rate calculation.
commit ce2e9e3703485563a0a5b6a57e4080ad45d91fd7
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 09:29:13 2019 -0600
arch/z80/src/ez80: Cosmetic and unnecessary clean-up or serial driver.
commit 77287c8508a7e3262068d3e8cf1c5f8e27f3a144
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 09:08:56 2019 -0600
arch/z80/src/common and arch/z80/src/ez80: Clean up some assertion-related logic.
commit 4d2d3594c22f7240119255825fce2d2437301404
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:48:21 2019 -0600
configs/makerlisp/nsh/defconfig: Enable STACKDUMP on assertion.
commit 76b7a2faa3f213dd26634dd9440d12f746cac097
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:47:55 2019 -0600
configs/makerlisp/include/board.h: Don't put the board in reset on a simple assertion, onlhy a full panic.
commit 0a0dc12edcd39c07696769cb7249d8c39a148ccc
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:46:54 2019 -0600
arch/z80/src/ez80/ez80_rtc_lowerhalf.c: Remove all references to alarm ID.
commit 1a4dba1075fcf6466e87520a8ba66bbf91d696d7
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:33:29 2019 -0600
configs/makerlisp/src/ez80_bringup.c: Fix an error that was causing MMC/SD to fail to initialize. Unfortunately now the system hangs.
commit 145a395c7a8e73336fe62caf803d108c59e306a5
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Mon Jun 17 07:32:50 2019 -0600
arch/z80/src/ez80: Add an RTC lower half driver. Initial commit is just the STM32 RTC lower half with name changes.
stm32: Fix config variable for romfs
I haven't tested this change,
but I suspect it does not build
if the romfs configuration is enabled.
But I have tested similar changes on nucleo-144:
Now aligned to:
9e622bd9a4
Change-Id: I4b89af66c5ef510fc00a64c212590116cd39d561
Forwarded: https://bitbucket.org/nuttx/nuttx/pull-requests/903/
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: PM and PWM
* configs: spresense: add SPI configuration
add SPI configuration for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add support for PWM
add support for PWM for cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable PWM support
enable PWM support on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Power Management PROCFS support
the powermanager procfs support will export
/proc/pm:
clock
power
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable powermanager procfs support
The powermanager procfs is disabled by default and need to be enabled
by the CONFIG_CXD56_PM_PROCFS option
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add timer driver
Add timer driver for cxd56xx.
NOTE
The timer allows a divider of 1, 16 and 256 options
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Watch Dog Timer
Add Watch Dog Timer on cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable timer
the platform support has been added and now we can use the timers
on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable WatchDog timer
The platform support has been added and now we can use the WatchDog
Timer on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
stm32 h7 Add ADC and a few fixes for timer and Serial
* stm32h7:Fix error when SINGLEWIRE or CONFIG_STM32H7_SERIALBRK_BSDCOMPAT defined
* stm32h7:time fixed compile errors with TIM13,TIM14, TIM7
* stm32h7:Added ADC Driver
* stmh7x3:Added ADC pins to pin map
* stm32h7:Added ADC clocking
* nucleo-h743zi:Add ADC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
rndis on spresense
* arch/arm/src/cxd56xx: Fix ep0 out packet handling in cxd56_usbdev.c
This change fixes to handle ep0 out packet which exceeds EP0_MAXSIZE.
For example, 76 bytes of out packet is sent from rndis host during
rndis negotiation and finally the packet is split into two out packets
(64 bytes out packet + 12 bytes out packet). To handle these packets,
actual ep0reqlen is stored during ep0 out setup stage, and if all
out packets are received, it dispatches to cxd56_ep0setup(), otherwise,
it sets up the internal USB DMA to receive remaining out packets.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense: Add support for rndis configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
configs: Fix mac address settings for rndis
Recently CONFIG_NETINIT_MACADDR_2 and CONFIG_NETINIT_MACADDR_1
were newly introduced instead of CONFIG_NETINIT_MACADDR.
This PR conforms to this change.
Signed-off-by: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_mmuinit should be called z80_mmu_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_loweserialinit should be called z80_lowserial_initialize.
configs/z80sim/src/z80_serial.c: Remove unused function up_earlyserialinit()
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_serialinit should be called z80_serial_initialize.
nuttx/arch/z80/src: To properly follow the coding standard, the z80 architecture common should up_doirq should be called z80_doirq.
arch/z80/src/common: up_addregion() must be prototyped in nuttx/mm/mm.h, not up_internal.h
configs/makerlisp/src/ez80_spi.c: Add hooks needed by SPI driver. Move SPI MMC/SD chip selected configuration from ez80_lowinit.c to here as it done in other NuttX architectures. This enables support for multiple devices on the SPI bus.
Squashed commit of the following:
configs/makerlisp: Update comments about use of serial console.
configs/makerlisp: Add LED support, remove vestiges of button support (the board has no user buttons). Add support for SPI-based MMC/SD card slot.
arch/z80/src/ez80: Fix some link problems.
libs/libc/syslog/lib_syslog.c: The ZDS-II toolchain does not declare va_coy in stdarg.h. I think that the use of va_copy in vsyslog() is no necessary.
configs/makerlisp: Initial configuration directories cloned from ez80f910200zco with little more than naming changes.
ez80: Fixing a few more compile problems. I am afraid that the 5.3.0 compiler it too buggy to use.
ez80: Additional build-related fixed.
eZ80: Updating to use the newest ZDSII 5.3.0 toolchain.
Squashed commit of the following:
configs/: Add . = ALIGN(4); before every .data section
configs/: Add . = ALIGN(4); before every ARM.extab section
configs/: Add . = ALIGN(4); before every definition of __exidx_start
configs/: Add . = ALIGN(4); before every .init_section.
configs/: Convert TABs to spaces in all ld linker scripts. This just makes things easier to modify with scripts because the files are more consistent.
Improvements for STM32 PWM
arch/arm/src/stm32/stm32_pwm: add support for all PWM modes
arch/arm/src/stm32/stm32_pwm: add interface to change PWM mode
arch/arm/src/stm32/stm32_pwm: refactor pwm_mode_configure()
arch/arm/src/stm32/stm32_pwm: STM32_PWM_CHANx corresponds to the timer channel and STM32_PWM_OUTx corresponds to the timer channel output
arch/arm/src/stm32/stm32_pwm: add CHAN5 and CHAN6 to PWM_TIMx_NCHANNELS
arch/arm/src/stm32/stm32_pwm: calculate the PWM_TIMx_NCHANNELS if CONFIG_STM32_PWM_MULTICHAN is selected
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
arch/arm: Rename include/stm32f0l0 and src/stm32f0l0 to stm32f0l0g0.
Change all occurrences of lower-case stm32f0l0 to stm32f0l0g0.
Change all occurrences of upper-case STM32F0L0 to STM32F0L0G0.
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
