Modify the file according to the checks
update the board config files, and modify the gd32f4xx_progmem.c
Add chip GD32F450 of GD32MCU
delete the micro FAR, modify code style
Add chip GD32F450 of GD32MCU
* boards/arm/tiva/tm4c129e-launchpad: New subdirectory providing
board support for the Texas Instruments TM4C Crypto Connected
LaunchPad, or more correctly the EK-TM4C129EXL.
* Documentation/introduction/detailed_support.rst,
Documentation/introduction/supported_platforms.rst,
boards/README.txt: Document the additional board support.
* boards/Kconfig:
(ARCH_BOARD_TM4C129E_LAUNCHPAD): New config.
(ARCH_BOARD): Add tm4c129e-launchpad.
(Board-Specific Options): Source the board-specific Kconfig
boards/arm/tiva/tm4c129e-launchpad/Kconfig when selected.
Summary:
- I noticed that error happens in loading nettest elf application.
- This commit fixes this issue by adding SYMTAB to the NSH
as well as adjusting some parameters in CONFIG_ELF_XXX
- Also, CONFIG_EXAMPLES_HELLO is changed from y to m for testing.
Impact:
- lm3s6965-ek:qemu-protected only
Tested:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Remove ifeq and endif and replace them with CSRC-$(CONFIG) form.
This simplifies Makefile and makes it a tiny bit more readable.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This commit adds support for GPIO driver based encoder for SAMv7 boards.
This encoder do not use the microcontroller's dedicated driver but two
GPIO pins with interrupts. The position is calculated based on those
interrupts.
This can be used for boards that do not have pins routed to the dedicated
driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The SPI2_CS_X and SPI2_SCK pins are used for connection to the LTE modem.
These pins are the special pins for the host interface that are set
automatically by latching the SYSTEM0/1 pins. So, it causes a problem
with increased current consumption when the modem is in power off state.
To prevent it, set these pins to GPIO HiZ during board initialization.
When nsh is not enabled, CONFIG_NSH_PROC_MOUNTPOINT is not defined.
If in that case procfs is used, compilation will result in error.
Define sane default path for procfs in case nsh is not enable but
procfs is.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
When CONFIG_ARCH_BOARD_FLASH_CPU2_PROG_SIZE is bigger than 0, compilation
will fail because of missing "{}" in struct initialization.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
If not all partitions are defined in Kconfig, compiler may show -Wundef
warnings for each: "#if CONFIG_ > 0". Fixed by defaulting values to 0
if they are undefined.
Some variables may be unused if filesystems are not enabled in Kconfig.
These variables are marked as UNUSED() to silent compiler warnings.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
Summary:
- This commit enables to test C++ static object in ELF (hello++3)
Impact:
- elf defconfig only
Testing:
- Tested with QEMU and sabre-6quad board
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit enables to test C++ static object in ELF (hello++3)
Impact:
- elf defconfig only
Testing:
- Tested with spresense
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
and remove CONFIG_LIBC_LONG_LONG option to simplify the usage.
note: the size will increase 668
before change:
text data bss dec hex filename
168440 348 4480 173268 2a4d4 nuttx
after change:
text data bss dec hex filename
169108 348 4480 173936 2a770 nuttx
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
SAMA5D2 and SAMA5D4 does not support external reset.
Some SAMA5 board's Kconfig contain item SAMA5_SYSTEMRESET, but it is better in arch/arm/src/Kconfig.
In order to support multiple LCD instances per board, add a pointer from
lcd_planeinfo_s to the lcd_dev_s which it belongs to. Also enhance the
putrun, getrun, putarea and getarea methods to pass through the
lcd_dev_s pointer to the respective device driver.
Port all LCD device drivers to this lcd_planeinfo_s extension.
Enhance SSD1306 driver to support multiple LCDs.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
This patch adds working integration of progmem FLASH. User can partition
internal FLASH memory to up to 4 partitions and use any combination of
raw, nxffs, smartfs and mtd_config filesystems (unless there are other
limitations like nxffs supports only single instance).
Support for dual CPU is added to Kconfig to not overwrite CPU2 program code.
Code guards user to not allocate more memory than there is on FLASH, and
warns user if not all FLASH memory is used. Errors will be printed when
user tries to initialize two instances of nxffs or mtd_config filesystems.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This patch adds to the nucleo-wl55jc previously implemented EXTI support.
Button support with nuttx's button driver is added.
I've written small example to show how to use GPIO EXTI. B3 button can be
used (selectable via Kconfig) to toggle Red LED.
I've added new defconfig for demo purposes. I've included there config
and enabled example programs that are meant to demonstrate functions of
the board and does not really have a place in real world project. Like
Red LED can be toggled with B3 button, or LED example that flashes LEDS,
or button example to show which button has been pressed.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- Change (1 << 0) to (1 << BUTTON1_BIT (and similar)
v2 -> v3:
- Fix invalid BUTTON3_BIT value
v3 -> v4:
Suggested by: Petro Karashchenko
- Change 0/1 to false/true
This patch includes bare minimum support for nucleo-wl55jc board.
It compiles and nsh shell is working properly on virtual com port
over USB. 3 onboard leds with userled driver are working.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
The driver is provided by Spresense SDK
ISX019 has the DOL-HDR feature, which combines images with different exposure so that
both bright and dark data of high-contrast subject can be viewed at the same time.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Change pin initialization timing for camera from board power on to camera device
power on for the following purposes.
- avoid unnecessary power consumption
- Make the corresponding pins available for other uses when camera is not in use
RF and system timer interrupt are used for ble.
tlsr82_flash.c:
1. BLE will loss packets during flash operation beacause the interrupt
is disabled and the operation take too long (especially erasing,
about 100ms), so allow RF and system timer interrupt during flash
operation;
2. Add sched_lock()/sched_unlock() to avoid the task switch in ble and
system timer interrupt;
flash_boot_ble.ld:
3. Because of 1, the code executes in RF and system timer interrupt
must be in ram to avoid bus error. The sem_post() will be called and
const variable g_tasklisttable will be accessed in RF and system
timer interrupt handler;
4. To improve the performance, copy some frequently called function to
ram as well, such as: sem_take(), sched_lock(), sched_unlock(),
some lib functions, some zephyr ble functions and some tinycrypt
functions;
5. The RF and system timer interrupt handler will call some libgcc
functions, so copy all the libgcc functions to ram exclude _divdi3.o,
_udivdi3.o and _umoddi3.o;
tlsr82_serial.c
6. Make up_putc() be thread safe, add enter/leave_critical_section() in
function uart_send_byte();
tc32_doirq.c
7. Increase the RF and system timer interrupt response priority;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
since the code could map the unsupported work to the
supported one and remove select SCHED_WORKQUEUE from
Kconfig since SCHED_[L|H]PWORK already do the selection
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
1. Add vbat mode for chip internal voltage sample;
2. Add adc channel config;
3. Using DFIFO2 to get the sample value, follow telink sdk.
4. Add calibration function and config;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
1. add pulse count support for pwm0;
2. add more detailed config for pwm;
3. pwm configuration and start process optimize;
4. tlsr82/Kconfig format;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Summary:
- The configuration is no longer needed because Kconfig has
been fixed in the previous commit
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that cxxtest does not work correctly.
- Finally, I found that initializers for c++ is not called.
- This commit fixes this issue
Impact:
- None
Testing:
- Tested with cxxtest (defconfig will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Follow: http://glennastory.net/boot/sysinit.html
This is first script that init runs is rc.sysinit. This
script does serval initialization tasks about basic service.
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(Peripherals driver, core driver, ...)->
run rcS script(mount fs, run service) ->
board_appinitialize->
After this patch:
The boot sequence currently provided to the board level is:
board_earlyinitialize->
board_lateinitialize(core driver,...)->
run rc.sysinit script(mount fs, run core service) ->
board_appinitialize(Peripherals driver)->
run rcS script(run other service)->
So, Peripheral drivers can do more with the file system and
core services.
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
since it is broken and inefficient, and then removed by:
commit dc961baaea
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 14 18:07:14 2022 +0800
arm/armv7-[a|r]: move fpu save/restore to assembly handler
Save/Restore FPU registers in C environment is dangerous practive,
which cannot guarantee the compiler won't generate the assembly code
with float point registers, especially in interrupt handling
Signed-off-by: chao.an <anchao@xiaomi.com>
commit 8d66dbc068
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 7 13:48:04 2022 +0800
arm/armv[7|8]-m: skip the fpu save/restore if stack frame is integer-only
Signed-off-by: chao.an <anchao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
It caused i2c tool not to work due to i2c uninitializing processing.
Since this process is not necessary in the normal case, we will
move it to the error case.
Add MCUboot Update Agent and Slot Confirm configurations. It uses
ethernet with dhcp client to perform download of new image into
internal flash memory.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
MCUboot apps were moved to examples directory. This fix configs due to
recent changes.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Summary:
- This commit enables environ and path in knsh/defconfig
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that undefined instruction happens with getprime and gcc-10.3.1
- Actually, the issue does not happen with gcc-9.3.1
- This is a tentative solution to avoid the issue
Impact:
- sabre-6quad:knsh only
Testing:
- Tested with hello/getprime
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The imxrt1064, imxrt1064, and teensy-4.x board configs would fail to
build when CONFIG_USERLED_LOWER was enabled, due to a missing header in
imxrt_appinit.c and an unset local define.
Verified a build succeds for the specified boards with the following
defconfig modifications:
# CONFIG_ARCH_LEDS is not set
CONFIG_USERLED=y
CONFIG_USERLED_LOWER=y
Tested the "leds" Led driver example on a Teensy 4.1.
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- Add sabre-6quad:knsh to test BUILD_KERNEL with qemu
- Update README.txt to run the nuttx with qemu
Impact:
- None
Testing:
- Tested with QEMU
- NOTE: getprime crashes with undefined instruction when
compiled with gcc 10.3.x (please use 9.3.1)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds thumb support to i.MX6
- Also, applies the same coding style to arch_elf.c
Impact:
- i.MX6 only
Testing:
- Tested with sabre-6quad:smp (QEMU, Dev board)
- Tested with sabre-6quad:netnsh (QEMU)
- Tested with sabre-6quad:netknsh (QEMU, not merged yet)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The LSM303AGR and LSM6DSL depend on BSD license and should be disabled by default
They can be enabled after BSD components are selected in menuconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
NET_TUN depends on BSD components
Can be enabled after developer enables the BSD_LICENSE option in the menu
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
The BSD components should not be enabled by default.
Each developer can enable non Apache components locally
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- I noticed two issues in the previous commit
- QEMU setting is missing
- The ostest takes longer time (i.e. 6m13s)
- This commit fixes these issues
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
## Summary
A lot of linker scripts were listed twice, once for unix, once for windows.
This PR cleans up the logic so they're only listed once.
## Impact
Any opportunity to use a single source of truth and reduce lines of code is a win!
## Testing
CI will test all build
State of problem:
- Some drivers that do not support write operations (does not
have write handler or ioctl do not perform any write actions)
are registered with write permissions
- Some drivers that do not support read operation (does not
have read handler or ioctl do not perform any read actions)
are registered with read permissions
- Some drivers are registered with execute permissions
Solution:
- Iterate code where register_driver() is used and change 'mode'
parameter to reflect the actual read/write operations executed
by a driver
- Remove execute permissions from 'mode' parameter
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Summary:
- I noticed that the following error happened when loading the init
'elf_symvalue: SHN_COMMON: Re-compile with -fno-common'
- This commit fixes this issue
Impact:
- sabre-6quad only
Testings:
- Tested with sabre-6quad:netknsh (not merged yet)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Support for the STMicroelectronics B-U585I-IOT02A development board. This
is a proof-of-concept port that demonstrates running NuttX as the
Non-Secure TrustZone domain companion to TrustedFirmware-M.
Signed-off-by: Michael Jung <mijung@gmx.net>
This commit adds board level support of PWM driver to SAME70-XPLAINED
board. The functionality is tested with two new configurations
pwm:
An example configuration with configured PWM.
pysim:
This configuration contains support for pysimCoder application and
includes ADC and PWM peripherals and Ethernet driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
board: nucleo-l152re: Added registering logic I2C on /dev.
squash 5 commits
board: nucleo-l152re: Add missing I2C1 GPIO definition
I2C1 not worked due to it's GPIO pin definition has been missing on board.h.
Fix it through include two pin macros on stm32l15xxx_pinmap.h(arch/arm/src/stm32/hardware) to board.h
GPIO_I2C1_SCL => PB8 (CN5 pin 10, D15)
GPIO_I2C1_SDA => PB9 (CN5 pin 9, D14)
Added board_late_initialize() function for init I2C.
board: nucleo-l152re: Added registering logic I2C on /dev.
I2C1 hasn't been registered on /dev. Fix it.
board: nucleo-l152re: Fix code style.
Update board.h
board: nucleo-l152re: Fix code style.
Variables starting with symbol '"g_*" means it is a global variable, I think this is not the case here.
Fix code style
