arch/arm/src/tiva/hardware: Add CC13xx SMPH and AUX SMPH header files. Still need DDI0 OSC header file for CC13x0 compilation.
arch/arm/src/tiva/cc13xx: A few changes toward getting the launchxl-cc1310/nsh configuration to build
Squashed commit of the following:
confgs/launchxl-cc1310: Add board support for the LaunchXL-CC1310. This is a work in progress and does not yet build error free.
arch/arm/src/tiva/cc13xx: cc13x0_trim.c now compiles; Make xxx_rom.h header files conform a little more closely to the NuttX coding style.
arch/arm/src/tiva/cc13xx: CC13x2 (V1 and V2) rom.c files now build with no errors or warnings. Still have to work through the CC13x0 version.
arch/arm/src/tiva/hardware: Add CC13x0/CC13x2_CC26x2 AON BATMON register definition header file.
arch/arm/src/tiva/cc13xx: A little more progress converting TI DriverLib ROM code to NuttX coding style. Lots of possibilities for breakage here!
arch/arm/src/tiva/cc13xx: Remove functions from cc13x._rom.c that are defined from ROM access in cc13x._rom.h; Add prototypes in cc13x._rom.h for functions in cc13x._rom.c that are not defined in cc13x._rom.h.
arch/arm/src/tiva/cc13xx: Remove some dangling whitespace at the end of lines.
arch/arm/src/tiva/cc13xx: Second (and final) round of name changes to get ROM function-like defines consistent with NuttX coding standard
arch/arm/src/tiva/cc13xx: Fix a few errors in last big name conversion.
arch/arm/src/tiva/cc13xx: First round of name changes to get ROM function-like defines consistent with NuttX coding standard
arch/arm/src/tiva/cc13xx: Remove ROM_ prefix from function-like defines.
stm32: Align ethernet config name to netnsh
nsh-ethernet was only used for stm32f7*-disco,
other configurations with network enabled are commonly
named netnsh or derived: (eg: nucleo-144/f7670-netnsh)
Change-Id: I80a33c8e22fbc7ccc9caf6b483478ae2c3a075ad
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
nucleo-144-f767-netnsh: Add ethernet config
* nucleo-f767zi: Use on board USB UART as default console
Board is powered by USB which can be used as UART link for upload and console
Previously it was set to use Arduino shield which developer may not have,
Change-Id: If3c1e3a71b4af0ca5f842f70e8b4dd2701bd4155
Signed-off-by: Philippe Coval <p.coval@samsung.com>
* nucleo-144-f767-netnsh: Add ethernet config
Based on nsh's config
plus stm32f769i-disco/nsh-ethernet
(which should be renamed to align netnsh)
Usage:
mount -t procfs /proc ; ifconfig -a
mkdir /tmp ; mount -t tmpfs /tmp
ifdown eth0
ifconfig eth0 hw 00:80:E1:34:ff:ff; ifconfig
ifup eth0; renew eth0 ; ifconfig
ping 8.8.8.8 ; ping ifconfig.me
cd /tmp/ ; wget http://ifconfig.me/ip ; cat ip
Change-Id: If7da7f33da8676726c42bce41077faf956b99701
Signed-off-by: Philippe Coval <p.coval@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
configs/stm32f4discovery: Update rndis configuration
Add NFS and adjusted stack size for usermain and telnetd client.
Add support for loadable application and ping.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
I still observe data abort crash if I compile the code with optimization enabled.
The next steps are to investigate the optimization issue and add Watchdog module. Currently, NSH does not run for a long time ;)
arch/arm/src/am335x/am335x_irq.c: Correct interrupt processing routine
configs/beaglebone-black/nsh/defconfig: Enable debug compilation options. Otherwise data abort crash is observed
arch/arm/src/am335x/am335x_lowputc.c and arch/arm/src/am335x/chip/am335x_uart.h: UART-related cosmetic changes
arch/arm/src/am335x/am335x_timerisr.c: Make sure that Timer 1 interrupts are disabled before any access to peripheral registers
stm32f0l0: SPI and GPIO EXTI support
arch/arm/src/stm32f0l0: add support for GPIO EXTI
configs/nucleo-l073rz: support for nrf24l01
configs/b-l072z-lrwan1/include/board.h: add note about onboard Murata CMWX1ZZABZ-09 module and definitions for available peripherals
Approved-by: GregoryN <gnutt@nuttx.org>
configs/lc823450-xgevk: Enable NFS client for rndis
Also, some stack size were adjusted to work with NFS
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Many small changes related to coding style.
Author: Petro Karashchenko <petro.karashchenko@gmail.com>
configs/beaglebone-black: Adds initial support for the BeagleBone Black board.
arch/arm/src/am335x: Adds initial support for the TI AM355x family.
Squashed commit of the following:
arch/arm/src/stm32f0l0: Various changes for a clean compilation. Still does not compile correctly due to missing FLASH latency definitions.
arch/arm/src/stm32f0l0/hardware: Add framework for the STM32 L0. Currently set to same as the STM32F0.
arch/arm/src/stm32f0l0/hardware: Very fragmentary FLASH header register definitions for the STM32 L0.
arch/arm/src/stm32f0l0: Bring in DMA v1. Cannot possibly be functionaly yet due to the limited number for M0 interrupts.
arch/arm/src/stm32f0l0: Add STM32 F0/L0 LSE and backup power domain controls.
arch/arm/src/stm32f0l0/hardware/stm32l0_pwr.h: Add STM32L0 PWR header file.
arch/arm/include/stm32f0l0/chip.h: Clean up WIP chip header file.
arch/arm/include/stm32f0l0/chip.h: WIP.
arm/src/stm32f0l0: Resolve some small differences between F0 and L0 GPIO pin options.
arch/arm/src/stm32f0l0: Better integrate STM32L0 header files.
nuttx/arch/arm/include/stm32f0l0: Add STM32L0 IRQ number definition file.
arch/arm/src/stm32f0l0: Add STM32L0 RCC driver.
arch/arm/src/stm32f0l0/hardware: Adds basic STM32L0 header files.
arch/arm/src/stm32f0l0: Add STM32L0 chip selections.
configs/: Hook new STM32L0 boards into the configuration system.
configs: nucleo boards use as default ST LINK MCO as clock input from MCU and for this HSEBYP must be enabled
configs: add basic support for nucleo-l073rz
configs: add basic support for b-l072z-lrwan1
Change rndis mac
* configs/lc823450-xgevk: Change RNDIS MAC address assignment
In previous implementation, mac[0] was assigned to 0xaa for RNDIS
host to avoid MAC address conflicts with RNDIS device.
However, I noticed that this assignment causes a random MAC address
generation on ubuntu16.04 or later which is inconvenient to set up
network interface.
This new assignment scheme fixes this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/stm32f4discovery: Change RNDIS MAC address assignment
In previous implementation, mac[0] was assigned to 0xaa for RNDIS
host to avoid MAC address conflicts with RNDIS device.
However, I noticed that this assignment causes a random MAC address
generation on ubuntu16.04 or later which is inconvenient to set up
network interface.
This new assignment scheme fixes this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/viewtool-stm32f107: Change RNDIS MAC address assignment
In previous implementation, mac[0] was assigned to 0xaa for RNDIS
host to avoid MAC address conflicts with RNDIS device.
However, I noticed that this assignment causes a random MAC address
generation on ubuntu16.04 or later which is inconvenient to set up
network interface.
This new assignment scheme fixes this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Fix lc823450 related
* configs/lc823450-xgevk: Fix IOB params in rndis/defconfig
These prameters work for HTTP audio streaming.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch/arm/src/lc823450: Fix up_allocate_heap() in lc823450_allocateheap2.c
This change fixes heap size and also implements up_addregion().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/stm32f0l0: Some fixes for a clean build. Still have a problem with lots of error messages coming from kconfig-mconf, but the configuation looks fine. Sometimes kconfig errors are difficult to spot. I would appreciate it anyone can spot the issue.
arch/arm/src/stm32f0l0/hardware: Rename the chip directory to hardware. This will hopefully eliminate some problems that I have seen with the chip include paths not being unique in more complex configuartions.
configs/nucleo-f072rb, configs/nucleo-f091rc, configs/stm32f051-discovery, and configs/stm32f072-discovery: Update for all of the naming changes made in arch/arm/src/stm32f0l0
arch/arm/include/stm32f0l0: Rename stm32f0 to stm32f0l0 to make a speace for STM32 L0. Rename files, functions and defines, removeing the f0_ from the names in order to make them MCU agnostic.
arch/arm/src/stm32f0l0: Rename stm32f0 to stm32f0l0 to make a speace for STM32 L0. Rename files, functions and defines, removeing the f0_ from the names in order to make them MCU agnostic.
arch/arm/src/tiva: Add GPIO IRQ stubs for clean compile
arch/arm/src/tiva/cc13xx: Add build framework for CC13xx GPIO interrupts. Change prototypes of some GPIO IRQ interfaces so that the function prototype is common between LM3S, LM4F, TM4C, and CC13xx.
Master
configs/nucleo-f334r8: add example for the SPWM generation (custom STM32 PWM usage)
arch/arm/src/stm32/stm32_pwm: fix compilation errors if the upper-half PWM logic is not enabled
include/nuttx/drivers/pwm.h: remove dependency on CONFIG_PWM for the upper-half PWM header. This allows compilation for the lower-level PWM drivers even if the upper-half PWM logic is not used.
arch/arm/src/stm32/stm32_tim.c: fix compilation error if there is no TIM8
configs/nucleo-f334r8/highpri: remove the upper-half ADC from configuration
configs/nucleo-f302r8/highpri: remove the upper-half ADC from configuration
configs/stm32f429i-disco/highpri: remove the upper-half ADC from configuration
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/tiva: Add CC13xx GPIO driver plus various fixes for clean compilation.
arch/arm/src/tiva/ and configs/launchxl-cc1312r1: Make type of the GPIO pin configuration an abstract type so that CC13xx MCUs can share the same GPIO function prototypes and usage model.
Improvements in STM32 ADC
arch/arm/src/stm32/stm32_adc.c: start conversion on startup is now possible if TIM triggering selected. This can be useful to start ADC TIM conversion for ADC IPv2 when opening ADC device.
arch/arm/src/stm32/stm32_adc.c: fix compilation errors for chips with one ADV TIM
configs/nucleo-f303re: refresh ADC example
configs/nucleo-f334r8: refresh ADC example
Approved-by: GregoryN <gnutt@nuttx.org>
