The function is not relevant any longer, remove it. Also remove
save_addrenv_t, the parameter taken by up_addrenv_restore.
Implement addrenv_select() / addrenv_restore() to handle the temporary
instantiation of address environments, e.g. when a process is being
created.
Detach the address environment handling from the group structure to the
tcb. This is preparation to fix rare cases where the system (MMU) is left
without a valid page directory, e.g. when a process exits.
NuttX kernel should not use the syscall functions, especially after
enabling CONFIG_SCHED_INSTRUMENTATION_SYSCALL, all system functions
will be traced to backend, which will impact system performance.
Signed-off-by: chao an <anchao@xiaomi.com>
PWM driver for multiple peripherals supplied in gateware.
Only single channel frequency and duty cycle control is implemented. Pulse counting and multichannel features are not currently feasible.
Additions also include a new board configuration for arty-a7 which enables the PWM driver and example application.
This is preparation for moving address environments out of the group
structure into the tcb.
Why move ? Because the group is destroyed very early in the exit phase,
but the MMU mappings are needed until the context switch to the next
process is complete. Otherwise the MMU will lose its mappings and the
system will crash.
There were two issues with signal handling:
- With a kernel stack the "info" parameter was passed from kernel memory.
This is fixed by making a stack frame to the user stack and copying it
there.
- If the signal handler uses a system call, the kernel stack was completely
and unconditionally destroyed, resulting in a crash in the user application
There is also no need to check ustkptr, it is always NULL. Why ? Because
signal delivery is deferred when a system call is being executed.
The value printed by assert() cannot always be trusted to be correct,
as it relies on the stack / stack pointer not being corrupt.
The CPU register always points to the faulting instruction so print it
out in the exception handler.
MCUboot support is no longer behind EXPERIMENTAL for the following
chips:
- ESP32
- ESP32-S2
- ESP32-S3
- ESP32-C3
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Allow bootloader to select run-time whether the payload binary is booted with
SBI or directly by jumping to entrypoint address.
- Use just one bitmask to select sbi or direct boot for each hart
- Add mpfs_set_use_sbi function to allow selecting how to boot
- Initialize the bitmask by default according to the configuration flags
- Add a header file for including the function prototypes in bootloader code
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
SHM area is just mapped memory, the physical backup is not owned by the
process, so the process must not free it.
In ARM this is already handled as the regions are destroyed one by one,
while this implementation does a page directory walk instead.
The dependency should be vice versa; the MM_SHM should depend on the
existence of the virtual memory range allocator.
Create a new CONFIG flag CONFIG_ARCH_VMA_MAPPING, which will define that
there is a virtual memory range allocator. Make MM_SHM select that flag
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
which is made by:
commit 87a1f69a3c
Author: Alan Carvalho de Assis <acassis@gmail.com>
Date: Fri Dec 16 15:23:39 2022 -0300
Modify the IRQ APIs to be compatible with ESP32/S2/S3
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- I noticed that rv-virt:ksmp64 sometimes stops during boot.
- Finally, I found that it posts the Supervisor Software Interrupt
before the OS finishes hardware initialization.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with QEMU-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
"aes_cypher" is a function from NuttX crypto, so better use instead of
defining a new interface in the driver.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Summary:
- I noticed that mtimer stops around 30min after boot.
- Finally, I found that nesc overflows in riscv_mtimer_current().
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with rv-virt:nsh on QEMU-7.1
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
add the task from the specified task list to reduce time consuming.
It takes about 10 cycles to obtain the task list according to the task
status. In most cases, we know the task status, so we can directly
delete the task from the specified task list to reduce time consuming.
After commit b7d2b38, the system suffers from -Warray-bounds warning with -Wall:
chip/mpfs_opensbi.c: In function 'mpfs_hart_to_scratch':
chip/mpfs_opensbi.c:251:26: warning: array subscript hartid is outside array bounds of 'sbi_scratch_holder_t[0]' {aka 'struct sbi_scratch_holder_s[]'} [-Warray-bounds]
251 | return (unsigned long)(&g_scratches[hartid].scratch);
Fix it by reverting back to what is was earlier. g_scratches shouldn't be in the bss
region that would be zeroed out.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
After the commit b8b541f, the system would not start up properly
with certain coldboot conditions. For example, if the OpenSBI picked
hart4 as the coldboot hart in preference to hart3, the system would
get stuck due to stack corruption. OpenSBI uses a lottery mechanism
to pick the coldboot hart.
Also fix g_scratches area in such a manner than it will not get
initialized to zero. If several harts initialize the area to zero, there's
danger the stack pointer gets wiped out.
Now any coldboot hart works.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Currently the IHC (Inter Hart Communication) depends on OpenAMP and
rptun. However, the bootloader portion of the IHC doesn't need
either of them. Now they are wasting a lot of bootloader space.
Reorganize the bootloader portion into a separate file 'mpfs_ihc_sbi.c'.
This file contains the OpenSBI vendor extensions, or the only required
functionalities for the bootloader. On the other hand, 'mpfs_ihc.c'
contains the non-bootloader code.
This patch also makes it possible to utilize 2 RPMSG channels. This
has been tested so that 2 separate NuttXs on harts 1 and 2 communicate
with Linux kernel that runs on harts 3 and 4.
New configuration files are added as well:
- rpmsg-ch1: sample config for RPMSG
- rpmsg-ch2: sample config for another RPMSG channel
- rpmsg-sbi: sample bootloader config for RPMSG/OpenSBI
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This reverts commit ea9144bda8.
The commit made Icicle MPFS DDR useless. Revert the change for now.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
- Reduce "SPI Flash configuration" menu dependency on SPI Flash driver
just to MTD-related configs.
- Move SPI Flash Mode and Frequency configs to SPI Flash configuration
menu.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Make a separate config flag for enabling L2 cache. This is on by
default when compiling a standalone/bootloader configuration, but
can also be disabled for special cases, such as memory testing
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Summary:
- This commit refactors the entry point name for BUILD_KERNEL
to avoid misunderstanding the name
Impact:
- None
Testing:
- Tested with rv-virt:ksmp64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that the OS timer sometimes proceeds fast when
a task is scheduled to run on CPUO via IPI.
- Actually, qemu-rv implementation shares supervisor software
interrupt for both timer and IPI on CPU0.
- This commit fixes this issue.
Impact:
- qemu-rv only
Testing:
- Tested with qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds SMP support for BUILD_KERNEL
Impact:
- RISC-V: BUILD_KERNEL + SMP only
Testing:
- Tested with rv-virt:ksmp64 (will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Run-time check for L3 page table size, to ensure it is large enough
to map all of the kernel memory.
NOTE: The check has to be run-time, as KFLASH_SIZE/KSRAM_SIZE are really
linker relocation symbols, and thus cannot be utilized compile-time.
L3 table maps 2MB of memory, this brings an implicit requirement for
any L3 region to be aligned to 2MB. This commit adds build time sanity
checks to ensure this requirement is met.
For other SvXX architectures the boundary requirement (might be) is
different.
Summary:
- This commit introduces g_percpu_spin to avoid deadlock
in riscv_percpu.c instead of using the global spinlock.
Impact:
- None
Testing:
- Tested with rv-virt:knsh64 and rv-virt:ksmp64 (will be added later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This allows properly using 10/100Mbps also with 1G phy. Some gigabit PHYs
come out of reset with 1G advertisement enabled, causing other devices to
set up link with 1G. If, after this, the link is set to 10/100 on the mpfs,
the link won't work.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Summary:
- In RISC-V, BUILD_KERNEL uses S-mode and to use M-mode timer
we need to handle it by using OpenSBI or self-implementation.
- This commit adds M-timer self-implementation for BUILD_KERNEL.
Impact:
- qemu-rv only
Testing:
- Tested with rv-virt:knsh64 on qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I found inappropriate SET_CSR() usage in the function.
- This PR fixes this issue.
Impact:
- None
Testing:
- tested with rv-virt:knsh64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- I noticed that the OpenSBI library depends on the BSD license
- This commit fixes this issue
Impact:
- CONFIG_OPENSBI=y only
Testing:
- Build with icicle:opensbi (will be updated later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- Because a context switch issue still exists with FPU
the configs should be removed until it works.
Impact:
- None
Testing:
- Tested with ostest
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
undeclare TCGETS on esp32c3 when enable usbserial and termios
error:
chip/esp32c3_usbserial.c: In function 'esp32c3_ioctl':
chip/esp32c3_usbserial.c:411:10: error: 'TCGETS' undeclared (first use in this function)
Situation:
Assume we have 2 cpus, and busy run task0.
CPU0 CPU1
task0 -> task1 task2 -> task0
1. remove task0 form runninglist
2. take task1 as new tcb
3. add task0 to blocklist
4. clear spinlock
4.1 remove task2 form runninglist
4.2 take task0 as new tcb
4.3 add task2 to blocklist
4.4 use svc ISR swith to task0
4.5 crash
5. use svc ISR swith to task1
Fix:
Move clear spinlock to the end of svc ISR
Signed-off-by: ligd <liguiding1@xiaomi.com>
Simplify the clock mode from the board.h -files. Also make the
SD clock definable as well.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Some related products, such as Aries m100pfs, don't support eMMC
speeds up to 200MHz. Thus, provide option to select slower clock.
This has only to do with the clocking, no CMD6 is sent to select
high speed modes.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The L3 mapping function was just way too simplistic. Depending on memory
configuration it either works or not.
Noticed that with icicle:pnsh the software crashes due to instruction
page fault, reason is the map_region() implementation that does not
work for regions that are not aligned to 2MB (the L2 page size).
Implemented an extremely simplistic page table allocator for the L3
references, that should once and for all get rid of the L3 mapping issue.
NOTE: gran_alloc() cannot be used at this point, it is too early for it.
If the system starts up using the SD-card, and later wants
to switch to use the eMMC, it's not going to happen. SD-card
will be kept selected within the FPGA making the transition
fail.
It's been possible to switch from eMMC to SD, but now the
transition is possible for both directions.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Issuing the following commands doesn't succeed:
- conn
- disconn
- conn
This USB driver doesn't even disconnect without this patch.
If the USB driver has been started from another hart, closing it
will not disable the PLIC interrupt. This means it's possible many
harts get the USB interrupt and thus make the USB look very unstable.
Fix these problems by disconnecting the USB via the USB_POWER
register at shutdown and disabling the interrupt at shutdown. Also
clear the software internals via the mpfs_sw_setup() for the conn /
disconect loop to succeed.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
The underlying hardware supports 9 endpoints:
- EP0
- 4x IN EPs
- 4x OUT EPs
Currently the driver assumes every EP number is unique. This limits
the amount of EPs to 1 + 4 = 5. Utilize the EPs in such a manner
that all may be used.
Also fix a few error handling related bugs. Update the composite
driver to match the current situation as well.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
==2117790==ERROR: AddressSanitizer: global-buffer-overflow on address 0x64d9e3c0 at pc 0x59ac4e16 bp 0xcefe8058 sp 0xcefe8048
READ of size 1 at 0x64d9e3c0 thread T0
#0 0x59ac4e15 in up_nputs sim/up_nputs.c:54
#1 0x59a67e4c in syslog_default_write syslog/syslog_channel.c:220
#2 0x59a67823 in syslog_default_write syslog/syslog_write.c:101
#3 0x59a67f10 in syslog_write syslog/syslog_write.c:153
#4 0x59a651c3 in syslogstream_flush syslog/syslog_stream.c:60
#5 0x59a6564e in syslogstream_addchar syslog/syslog_stream.c:104
#6 0x59a6576f in syslogstream_putc syslog/syslog_stream.c:140
#7 0x5989fc4d in vsprintf_internal stdio/lib_libvsprintf.c:952
#8 0x598a1298 in lib_vsprintf stdio/lib_libvsprintf.c:1379
#9 0x59a64ea4 in nx_vsyslog syslog/vsyslog.c:223
#10 0x598a601a in vsyslog syslog/lib_syslog.c:68
#11 0x59b0e3dc in AIOTJS::logPrintf(int, char const*, ...) src/ajs_log.cpp:45
#12 0x59b03d56 in jse_dump_obj src/jse/quickjs/jse_quickjs.cpp:569
#13 0x59b03ea1 in jse_dump_error1(JSContext*, unsigned long long) src/jse/quickjs/jse_quickjs.cpp:602
#14 0x59b03dd9 in jse_dump_error(JSContext*) src/jse/quickjs/jse_quickjs.cpp:591
#15 0x59bed615 in ferry::DomComponent::callHook(char const*) src/framework/dom/component.cpp:65
#16 0x59bfe0ff in ferry::DomComponent::initialize() src/framework/dom/component.cpp:645
#17 0x59bb141d in dom_create_component(JSContext*, unsigned long long, unsigned long long, unsigned long long) (/home/wangbowen/project/central/vela_miot_bes_m0/bin/audio+0x365c41d)
#18 0x59b4c0d3 in AIOTJS::__createComponent(JSContext*, unsigned long long, int, unsigned long long*) (/home/wangbowen/project/central/vela_miot_bes_m0/bin/audio+0x35f70d3)
#19 0x5a56ec17 in js_call_c_function quickjs/quickjs.c:16108
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
Summary:
- I noticed that ps shows incorrect stack usage when running
getprime in the background.
- With CONFIG_ARCH_ADDRENV=y, a user task including pthread
allocates its stack in the user space that needs to be
accessed with a correct address environment.
- This commit fixes this issue.
Impact:
- CONFIG_ARCH_ADDRENV=y only
Testing:
- Tested with rv-virt:knsh64 on qemu-6.2
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- Current RISC-V/NuttX implementation assumes that text/data/heap
areas are continuous. In fact, CONFIG_ARCH_TEXT_VBASE and
CONFIG_ARCH_HEAP_VBASE are not used for memory allocation.
- This commit assigns dedicated virtual addresses for text and heap
which are the same approach to ARM-v7A/NuttX implementation.
Impact:
- None
Testing:
- Tested with rv-virt:knsh64 (will be updated later)
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
mpfs_write_tx_fifo() gets stuck in the following case:
- CDCACM is used
- ttyACM0 is opened and then closed from the remote end,
such as Linux or Windows
- data is written into ttyACM0 from NuttX
- tx fifo will never get empty and the system is stuck
Fix this by issuing an error code if the transmit fifo doesn't
proceed as expected. The error code is then propagated into
higher level keeping the system functional.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
nxsig_usleep() will wait for the next timer tick which is way
too much here. It's not sleeping 100 us, but rather, near 1/60 s.
This causes severe performance problems. Fix this by polling the
register for a while if the remote end is busy.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
- Clarify the macros MSSIO_EC_DEFAULT and MSSIO_EC_USB_DEFAULT
- Remove PULLDOWN bit from MSSIO_EC_DEFAULT, it was on by accident
- Fix some EC configuration macros; DRVSTR was wrong, clean up the others
- Define GPIO_PULLUP and GPIO_PULLDOWN like on many other platforms
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Since the commit cf22dd8 (related to OpenAMP update), the notifyid
is no longer NOTIFY_ALL, but the vq id.
Utilize the vq id now properly as it's being provided. However,
vq id 0 generates action.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
so the user could disable the full image instrumentation,
but enable the instrumentation by files or directories.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
so the user could disable the full image instrumentation,
but enable the instrumentation by files or directories.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
without UBSan
```
text data bss dec hex filename
85612 208 142258 228078 37aee nuttx
```
with UBSan:
```
text data bss dec hex filename
194290 98164 208634 501088 7a560 nuttx
```
```c
int main(int argc, FAR char *argv[])
{
uint32_t ptr[32];
printf("Hello, World!! %lu\n", ptr[64]);
return 0;
}
```
Try to run this sample:
```
nsh> hello
ubsan_prologue: ================================================================================
ubsan_prologue: UBSAN: array-index-out-of-bounds in hello_main.c:39:37
__ubsan_handle_out_of_bounds: index 64 is out of range for type 'uint32_t [32]'
ubsan_epilogue: ================================================================================
Hello, World!! 1070182368
nsh>
```
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
OpenSBI vendor extension calls must not cause scheduling, as they're
part of M-mode trap handling. Thus, comment out nxsig_usleep() as
well, which is occasionally taken and crashes the system in that
case. Fix this by commenting out lines that have the potential to
cause scheduling.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- I noticed that QEMU shows high CPU usage if the number of
CPUs does not match the kernel configuration. (e.g. -smp 8
and CONFIG_SMP_NCPUS=2)
- This commit fixes this issue.
Impact:
- qemu-rv only
Testing:
- Tested with the following configs
- rv-virt:smp64 (CONFIG_NCPUS=1/2/8)
- rv-virt:nsh64
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
It is not really needed; g_hart_stacks is only used during SBI init as
a temporary stack area. We can use the scratch area buffers for this, as
the scratch areas define almost 4K of extra space, which is used for
exception stacks anyway.
The L3 table address was calculated incorrectly. For every 2MiB of
mapped memory, an offset of 4KiB is needed from the base of the L3
table. The old calculation failed if paddr was not aligned to a 2MiB
boundary.
RX_FIFO_ADDRs and TX_FIFO_ADDR were misconfigured. These addresses
overlapped causing data corruption during high USB loads. For
example, data corruption was present during the following conditions:
1. Composite USB driver was used (CDC/ACM + Mass storage)
2. /dev/ttyACM0 was accessed instantly from Linux side when
starting up.
3. Training data was sent to /dev/ttyACM0 from NuttX from the
very beginning periodically.
It was observed that while Mass storage was negotiating, sometimes
data sent from NuttX to Linux via CDC/ACM was corrupt, although it
was sent properly on the TX fifo.
Also, don't access TXCSRL_REG_EPN_TX_FIFO_NE_MASK for EP0 as it's
not applicable.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Initialize .domains_init function entry point in sbi_platform_operations when
CONFIG_OPENSBI_DOMAINS=y. In this case, the board specific code must provide
the "board_domains_init" function.
Signed-off-by: Jouni Ukkonen <jouni.ukkonen@unikie.com>
With faster data transfer rates, it was seen that the read
requests occasionally were issued while the USB RX operation
was actually in progress. This patch makes sure the system
doesn't accidentally read the RX fifo while it's being filled
up, but rather, checks for the RXCSRL_REG_EPN_RX_PKT_RDY_MASK
flag. This flag indicates the packet is ready to be read.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
cache_dbus_mmu_set and cache_ibus_mmu_set return positive values in case
of errors, so DEBUVERIFY could never detect them since this macro checks
for negative values.
Besides, the successful execution of those functions is mandatory for
the reliable operation under Protected Mode, so the verification is
always performed, even when DEBUG is not enabled.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
