reason:
In SMP, when a context switch occurs, restore_critical_section is executed.
To reduce the time taken for context switching, we directly pass the required
parameters to restore_critical_section instead of acquiring them repeatedly.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
We can see them in ifconfig:
ap> ifconfig
wlan0 Link encap:Ethernet HWaddr 42:64:7f:b3:12:03 at UP mtu 1500
inet addr:10.0.1.2 DRaddr:10.0.1.1 Mask:255.255.255.0
inet6 DRaddr: ::
RX: Received Fragment Errors Bytes
00000b9b 00000000 00000000 21daf5
IPv4 IPv6 ARP Dropped
00000a33 00000137 00000031 00000000
TX: Queued Sent Errors Timeouts Bytes
00000ac4 00000ac4 00000000 00000000 1a2103
Total Errors: 00000000
Signed-off-by: meijian <meijian@xiaomi.com>
Since the introduction of the rp2350, the pico-sdk project has been
re-arranged and elf2uf2 has been merged in to a new 'picotool' binary
which is supplied and installed separately.
Make umm & kmm heap alloc more clear, and possible support FLAT build to
enable kernel heap.
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
1. correct the armv8-r fpu flag from vfpv3-d16 to fpv5-sp-d16
2. add neon support
This commit updates the build script to specify the FPU type of
`fpv5-sp-d16` when the processor is configured with a single-precision
FPU, and `neon-fp-armv8` when the processor is configured with a
double-precision + Advanced SIMD-capable FPU.
Note that the `fp-armv8` FPU type is an alias for double-precision FPv5
with 32 double-precision registers (refer to the GCC
`gcc/config/arm/arm-cpus.in` for more details); NEON is always
specified in case of a double-precision configuration because the
Cortex-R52 can only be configured as such.
Reference:
https://developer.arm.com/Processors/Cortex-R52
Instruction set:
Arm and Thumb-2. Supports DSP instructions and a configurable Floating-Point
Unit either with single-precision or double precision and Neon.
Signed-off-by: chao an <anchao@lixiang.com>
Make this_cpu is arch independent and up_cpu_index do that.
In AMP mode, up_cpu_index() may return the index of the physical core.
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
In corner case, the pending ISR will be triggered immediately
after enable the IRQ, this PR will setting CPU affinity first
to avoid routing the unexpected IRQ to other CPUs.
Signed-off-by: chao an <anchao@lixiang.com>
Some USB controllers can receive or send multiple data packets then
generate one interrupt. This mechanism can reduce the number of data
copies. Extend req buf to accommodate this.
Signed-off-by: yangsong8 <yangsong8@xiaomi.com>
In protected build mode, the syscall returns without setting correct value for the CONTROL register, which causes the userspace threads working in privileged mode after syscall.
Signed-off-by: pangzhen1 <pangzhen1@xiaomi.com>
Currently concerns only arm.
tools/ci/testlist/msys2.dat:
At the moment I only added the board nucleo-l152re:nsh
.github/workflows/build.yml:
Enabled cmake for msys2
since not all Armv7-m platform support double-precision floating
operations, so we add an extra option that help those specific platform
could define the single-precision floating operations.
for example, qemu-mps platform(armv7-m) support double-precision
floating operations, so we do not need to open
CONFIG_ARM_FPU_SINGLE_HARDWARE build options;
but for fc7300 platform(armv7-m) only support single-precision floating
operations, so if we pass "-fhard" build option to "ghs" compiler, then
the following instruction will be generated:
vcvt.f64.s32 d9, s18
which will fail to execute on fc7300 platform.
with "-fsingle" build option, the "ghs" compiler will generate hardware
instruction for single-precision floating operation, and generate
software instruction for double-precision floating operation.
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
To support greenhill compilation, LDFLAGS removes the code that adds -T through addprefix to ARCHSCRIPT(greenhill requires a space between -T and ldscript files, but addprefix didn't do it). However,if we modified like this, when ARCHSCRIPT has more than one ldscript, the -T is only added to the first ldscript, but not to the following ldscripts, which results in a warning when linking.
To solve this problem, we can just add a space after $(SCRIPT_OPT) when using addprefix, instead of deleting addprefix.
Signed-off-by: pangzhen1 <pangzhen1@xiaomi.com>
Only in the non-critical region， nuttx can the respond to the irq and not hold the lock
When returning from the irq, there is no need to check whether the lock needs to be released
we also need keep restore_critical_section in svc call
test:
Configuring NuttX and compile:
$ ./tools/configure.sh -l qemu-armv8a:nsh_smp
$ make
Running with qemu
$ qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic \
-machine virt,virtualization=on,gic-version=3 \
-net none -chardev stdio,id=con,mux=on -serial chardev:con \
-mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
armv7-m/arm_mpu.c: In function 'mpu_dump_region':
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 6 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 7 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%u' expects argument of type 'unsigned int', but argument 8 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
Modified the input parameters of mpu_initialize to require the caller to provide the number of entries in the table
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
Summary:
1.Modify the conditions for entering different include header files
2.Added pre-definition for _Atomic _Bool when it is missing
3.Added nuttx for stdatomic implementation. When toolchain does not support atomic, use lib/stdatomic to implement it
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
In a multicore task scenario, there may be a situation where the task runs on different cores at different time slices (when the task is not bound to a particular core).
When the task calls cache clean/flush(range > cache size), depending on the optimization, clean_all, flush_all are called. however, at this point, there may be dirty data or incomplete data profiles in the cache on the kernel that is running the task, which may result in dirty data being flushed into memory or make the application think that the flushed data should be successfully flushed into memory, leading to unknown consequences.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
Execute data and instruction sync barriers after writing MPU register,
to ensure MPU setting take effects that the new changes are seen.
testing in lm3s6965-ek:qemu-protected
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
According to the current design on the armv7-a platform,
only fiq is processed in TEE, while irq and fiq are processed
in REE.
If we enable the irq function in TEE, when we process
some signal-related scenarios in TEE,
such as the ostest sighand testcase, this testcase will
call up_irq_enable() to enable irq interrupt in the
arm_sigdeliver() function. After the signal processing
logic is executed, irq will be disabled again.
During the interval of enabling irq, some external device
irq interrupts will be enabled, but these external device
irqs do not have corresponding handlers registered in TEE,
so an "unexpected irq isr exception" will be triggered.
Therefore, a better implementation is to keep the original
implementation of the up_irq_enable() function, that is,
to enable only fiq in TEE and to enable irq and fiq in REE.
Then for vendor-specific requirements, such as the need to
briefly enable irq during the TEE initialization process
and then disable irq before starting APz in TEE, we directly
provide a separate implementation of enabling irq in the
vendor, without modifying the implementation of the public
up_enable_irq() function.
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
CC: unistd/lib_setregid.c "/mnt/yang/qixinwei_vela_warnings_04_23/nuttx/include/nuttx/irq.h", line 53: warning #193-D:
zero used for undefined preprocessing identifier "NR_IRQS"
# if NR_IRQS <= 256
^
"/mnt/yang/qixinwei_vela_warnings_04_23/nuttx/include/nuttx/irq.h", line 82: warning #193-D:
zero used for undefined preprocessing identifier "NR_IRQS"
#if NR_IRQS <= 256
CC: mount/fs_umount2.c "/mnt/yang/qixinwei_vela_warnings_04_23/nuttx/include/nuttx/irq.h", line 72: warning #193-D:
zero used for undefined preprocessing identifier "NR_IRQS"
#if NR_IRQS <= 256
Signed-off-by: yanghuatao <yanghuatao@xiaomi.com>
the greenhills compiler provide its own implementation of va_start,
va_end, va_arg, va_copy. so if we are build vela with greenhills
compiler, we should using the stdarg implementation provided by
greenhills, not our own
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
Pass CP15_CACHE_INVALIDATE argument with r1 register to cp15_dcache_op_level.
cache level is 0(L1 D-Cache) with r0 register.
prototype:
void cp15_dcache_op_level(uint32_t level, int op)
Signed-off-by: Jinliang Li <lijinliang1@lixiang.com>
"/mnt/yang/qixinwei_vela_warnings/nuttx/include/nuttx/spinlock.h", line 252: warning #76-D:
argument to macro is empty
SP_DSB();
^
"/mnt/yang/qixinwei_vela_warnings/nuttx/include/nuttx/spinlock.h", line 261: warning #76-D:
argument to macro is empty
SP_DMB();
^
"/mnt/yang/qixinwei_vela_warnings/nuttx/include/nuttx/spinlock.h", line 252: warning #76-D:
argument to macro is empty
SP_DSB();
^
"/mnt/yang/qixinwei_vela_warnings/nuttx/include/nuttx/spinlock.h", line 261: warning #76-D:
argument to macro is empty
SP_DMB();
^
"/mnt/yang/qixinwei_vela_warnings/nuttx/include/nuttx/spinlock.h", line 296: warning #76-D:
argument to macro is empty
SP_DSB();
^
Signed-off-by: yanghuatao <yanghuatao@xiaomi.com>
according to armv6-m/armv7-m arch reference manual:
the three ISB {<opt>}, DSB {<opt>}, DMB {<opt>} instructions <opt>
field are defined as:
Specifies an optional limitation on the ISB/DSB/DMB operation. Allowered
values are:
Full system ISB/DSB/DMB operation, encoded as option=='1111'. Can be
omitted.
All other encodings of the options are RESERVED.
the "#opt" field of "isb #opt"
So we could remove the options field in Armv7-m platform.
The following are the build error with greenhills compiler:
CC: common/arm_exit.c [asarm] (error #2071) /tmp/gh_001h70j1.si 92: bad parameter
isb 15
------^
[asarm] (error #2071) /tmp/gh_001h70j1.si 112: bad parameter
isb 15
------^
[asarm] (error) errors during processing
According to armv8-m arch reference manual:
the ISB/DMB instruction's "opt" encoding rule is same as
armv6-m/armv7-m, but the "DSB" instruction is different, in armv8-m, the
"DSB {<opt>}" field has two valid encoding options: 0b0000, 0b0100.
and all other encoding options are reserved.
In Armv7-a/Armv8-a, the dsb/dmb option field has 8 valid state value.
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
The following are the compile error that reported
by GreenHills compiler:
"/mnt/yang/qixinwei_commit/nuttx/include/arch/syscall.h", line 156 (col. 17): error #2036-D:
cannot allocate "reg0" to specified caller-saved register
"/mnt/yang/qixinwei_commit/nuttx/include/arch/syscall.h", line 157 (col. 17): error #2036-D:
cannot allocate "reg1" to specified caller-saved register
Then we fix this greenhills compilation error by explicitly specifying
the registers in the clobber list in the inline assembly code.
This fix is successful in compiling on the
nuttx/boards/arm/mps/mps2-an500/configs/nsh platform and passes
the ostest test.
However, if we keep the implementation the same for both the default
and Greenhills compilers, the default compiler will report the
following two issues:
1. the "sys_call6" function will report compile error when
compiling on "./vendor/qemu/boards/smartspeaker/configs/smartspeaker-knsh"
platform, the detailed error info:
CC: proxies/PROXY_mq_getattr.c In file included from /home/guoshichao/work_profile/vela_os/vela_qemu_1/nuttx/include/sys/syscall.h:35,
from /home/guoshichao/work_profile/vela_os/vela_qemu_1/nuttx/include/syscall.h:30,
from proxies/PROXY_mmap.c:5:
In function 'sys_call6',
inlined from 'mmap' at proxies/PROXY_mmap.c:9:22:
/home/guoshichao/work_profile/vela_os/vela_qemu_1/nuttx/include/arch/syscall.h:297:3: error: 'asm' operand has impossible constraints
297 | __asm__ __volatile__
| ^~~~~~~
2. when running on qemu-armv7-a platform, the modification to
"smh_call()" function will make the system fail to boot up, so
we need to keep the default compiler implementation and greenhills
compiler implementation separate
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
(cherry picked from commit cb48b749b1c9cad8cfb96bff7c5e9b6ebf20fc8a)
This adds the necessary defines to set the USARTs' kernel clock source
selection.
This is required for a configuration where the bootloader (running
before NuttX) changes the USARTs' clock selection, so they need to be
restored on board init.
This is according to the reference manual RM0399 page 448.
when the thread to backtrace is exiting, get_tcb and up_backtrace in
different critical section may cause try to dump invalid pointer, have
to ensure the nxsched_get_tcb and up_backtrace inside same critical
section procedure.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
The following warnings is fixed:
chip/sam_pwm.c:961:12: warning: unused variable 'regval' [-Wunused-variable]
961 | uint32_t regval;
chip/sam_serial.c: In function 'sam_dma_txavailable':
chip/sam_serial.c:2264:7: warning: unused variable 'rv' [-Wunused-variable]
2264 | int rv;
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Larger RX/TX buffers might be required for both FD and FD_BSW modes.
Default bit timing values are also changed since the original ones
did not provide correct results for default SAMv7 board clock selection
(150 MHz clock frequency). The current values provide correct bit timing
with sample point as close to 87.5 %.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This adds field type to canioc_bittiming_s structure that allows
to set/obtain bit timing for both CAN CC and CAN FD.
CANIOC_GET_BITTIMING is now bidirectional: user specifies type field
and gets other fields from the controller.
The commit also updates current CAN FD capable controllers using the
ioctl. The type is not checked for classical CAN only controllers
and nominal bit timing is returned regardless of type value.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Following warnings were caused by incorrect naming of few defines.
chip/sam_mcan.c:415:7: warning: "MCAN1_NTSEG1" is not defined, evaluates to 0 [-Wundef]
415 | # if MCAN1_NTSEG1 > 63
| ^~~~~~~~~~~~
chip/sam_mcan.c:418:7: warning: "MCAN1_NTSEG2" is not defined, evaluates to 0 [-Wundef]
418 | # if MCAN1_NTSEG2 > 15
| ^~~~~~~~~~~~
chip/sam_mcan.c:421:7: warning: "MCAN1_NSJW" is not defined, evaluates to 0 [-Wundef]
421 | # if MCAN1_NSJW > 15
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
