(1) unifies the iomux definitions - previously some pins had them, and some didn't. This effectively made it impossible to use the pinmuxes without editing the header file in the standard distribution tree.
(2) unifies the pin definitions so that every pin now has a suffix. This makes it *much* easier to see when a pin is in use in your code, because it will always have a definition in your board.h file.
For anyone who is already using this CPU, a couple of small changes are needed to existing code;
In respect of (1) add IOMUX decorators to your pin definitions. You will find defaults in haardware/imxrt_iomux.h. Every pin should have a IOMUX decorator and in general the defaults should be OK. So while previously in your board.h file you might have had;
You will now have;
In respect of (2) you will need to add selectors for any function that previously only had one pinning option. There aren't many of those but LPUART1 is a good example. That just means adding into your board.h something like;
board/boarctl.c: Add support for the new BOARDIOC_ROMDISK command. This allows applications to create ROMFS block drivers without illegal direct calls to romdisk_register.
include/sys/boardctl.h: Add basic definitions to support a ROM disk creation boardctl() command.
Squashed commit of the following:
drivers/: Run tools/nxstyle against all drivers/*.c.
boards/boardctl.c: Add new boardctl() command, BOARDIOC_MKRD, that can be used to create a RAM disk. This will replace the illegal call to ramdisk_register() currently used by NSH.
drivers/mkrd.c: Add wrapper around ramdisk_register() for creating a proper ramdisk.
Add DMA support for STM32L4+ series
* Add DMA support for STM32L4+
* stm32l4xrxx_rcc: enable "Range 1 boost" mode if any PLL freq above 80 Mhz
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: spresense: cleanup and new defconfig
* arch: cxd56xx: remove NVIC_SYSH redefinition
The NVIC_SYSH is already defined in nvicpri.h
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: enable SPRESENSE_EXTENSION
Enable high current mode for the Spresense Extension board on all examples
that have SDCARD support
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: ifdef SDCARD_TXS02612
The SD Card TXS02612 port expander is hosted on the Extension board and
should not be enabled if the extension board is not prezent.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: increase MQ_MAXMSGSIZE
This change is needed by the display driver on spresense platform
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: config: add lcd examples defconfig
This is a configuration for the basic nx examples
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* boards: cxd56xx: spresense: add Spresense Image Processor
Enable support for accelerated format convertor, rotation and so on.
using the CXD5602 image processing accelerator.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards:cxd56xx:spresense: initalize GNSS and GEOFENCE at boot
Add the optional initialization of GNSS and GEOFENCE at boot
if the drivers are enabled
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: spresense: add board_timerhook function
* boards: cxd56xx: spresense: add board_timerhook function
in preparation for SDK we muts have a weak board_timerhook function
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: usbhost: add missing endif
By accident an endif was missing.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: audio: add build barrier
The audio implementation should not be beuilt if the config
CONFIG_CXD56_AUDIO is not set.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch:arm:cxd56xx: add ge2d.h header
The header is used by imageproc.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
fix the following link error:
/usr/bin/ld: i386 architecture of input file `nettest_host.hobj' is incompatible with i386:x86-64 output
/usr/bin/ld: i386 architecture of input file `nettest_server.hobj' is incompatible with i386:x86-64 output
boards: stm32f4discovery: Add support for MMCSD_SPI
This PR works with STM32F4 Discovery Shield plus microSD click
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
math library is also needed, however, here are various ways to provide a
math library so CONFIG_LIBM is not now set.
boards/arm/stm32l4/nucleo-l476rg/scripts/Make.defs: Add required
definitiions if libcxx is enabled.
boards: arm: cxd56xx: audio: add power_control and audio_tone_generator
* boards: arm: cxd56xx: audio: add power_control
Add a simeple way to control the audio power for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: audio: add audio_tone_generator
Add a simple way to control the audio buzzer with defined frequency
for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
1. Serial (UART) driver (13 ports)
2. Ethernet driver
This port is provided on two boards
1. RSK RX65N-2MB
2. GR-Rose
The port is built on Cygwin environment.
As part of this port, we have created two documents
1. Readme.txt for each board
2. User manual to provide information about development environment setup
Both these documents are placed under
1. /boards/renesas/rx65n/rx65n-grrose
2. /boards/renesas/rx65n/rx65n-rsk2mb
We have run 'nxstyle' for coding guidelines and 'ostest' for testing NuttX features on test platform.
We have shared the log with no errors as confirmation of valid port.
boards: arm: cxd56xx: different updates
* boards: cxd56xx: spresense: initialize SCU at boot
The SCU has to be initialized at bootup on spresense board because several
functions depend on it.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: add audio control definitions
Add audio control definitions for the audio implementation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: add audio defconfig
Add defconfig for the audio implementation
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Spresense smp
* arch: arm: Add ARCH_GLOBAL_IRQDISABLE to ARCH_CHIP_CXD56XX in Kconfig
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Make fpuconfg() public in cxd56_start.c
NOTE: fpuconfig() is called in both cxd56_start.c and cxd56_cpustart.c
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Add support for SMP
NOTE: To run cxd56xx in SMP mode, new boot loader which will be
released later must be used.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* arch: arm: cxd56xx: Add irq routing for SMP in cxd56_irq.c
NOTE: In cxd56xx, each external interrupt controller can be
accessed from a local APP_DSP (Cortex-M4F) only. This commit
supports IRQ routing for SMP by calling up_send_irqreq() in
both up_enable_irq() and up_disable_irq().
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* boards: spresense: Add smp configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Remove hardcoded -DCLOCK_MONOTONIC from CFLAGS in Make.defs of several configurations. That defintiion is now automatically adding this define when CONFIG_LIBCXX=y.
cxd56xx: various fixes
* arch: arm: cxd56xx: Support to set any i2c frequency
This commit supports to be able to set the i2c frequency other than just
100 or 400 Hz.
* arch: arm: cxd56xx: Enable SD clock during access to SD card
- Improve GNSS low sensitivity with SD card inserted
- Reduce power consumption by stopping SD clock
* arch: arm: cxd56xx: Do PANIC() when cpu rx fifo is overflow
If CPU Rx FIFO is overflow, it's fatal error for system. In such a case,
this commit changes to allow the user to notice by calling PANIC() for
debuggability enhancement.
* arch: arm: cxd56xx: Fix compile error in sdhci debug code
* arch: arm: cxd56xx: Remove assertion in cpu tx queue
When CPU Tx queue is overflow, it returns -EAGAIN instead of assertion
to be able to retry.
* arch: arm: cxd56xx: Add configurations for cpu fifo elements
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Fix LPADC configuration
LPADC options defined in the same symbol name, so kconfig tool
couldn't process them correctly.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Update loader and gnssfw ver.17660
* arch: arm: cxd56xx: Fix hang-up when error interrupt occurs
Fix a problem that error interrupts are not cleared.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Fix sdhci semaphore
Fix inital value of semaphore in sdhci drive.r
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: Treat the initial value of LNA power as off
LNA is always turned power on when GNSS is started. So it is desirable
that the initial value of the LNA power is off by default.
* boards: cxd56xx: Remove initial setting of PIN_AP_CLK
PIN_AP_CLK is used as a port selector of SDIO expander on the extension
board, and is set output low in initalizing. Therefore, this pin cannot
be used for other board. To avoid this restriction, remove this initial
operation because this pin is pulled down by default on the extension
board.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
It appears Yann Morin's kconfig-frontends project has gone offline and
the website at http://ymorin.is-a-geek.org/projects/kconfig-frontends
is not responding. Until we can identify a "proper" upstream project,
use the snapshot in NuttX tools repository.
Replace (almost) all links to Yann Morin's kconfig-frontends in the
docs to point to the NuttX tools snapshot instead, with the following
exceptions:
nuttx/Changelog for version 6.17, 2012-04-14: Leave this historical
information intact.
nuttx/README.txt: Document the source of our snapshot.
boards: spresense: Add board initialization for isx012
Add isx012 initialization to the board and include the needed headers
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: spresense: add isx012 camera initialization and config
* boards: spresense: add isx012 camera initialization
Add the initialization for the isx012 camera sensor.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: spresense: add camera defconfig
For easy configuration add camera defconfig for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
Some scripts use TABs, others spaced. Make usage consistent.
Move __exidx_end assignment inside of brackets.
Remove old __exidx_end assignment.
Move __exidx_start assignment inside of brackets.
Remove old __exidx_start assignment
noards: arm: cxd56xx: migrate common code
* boards: arm: cxd56xx: common: move boot to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move flash to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move I2C driver to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move uid to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: move usbmsc to common
This is a common function and can be reused by all boards.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56: add SPH
The SPH is used by the ASMP implementation from the SDK.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
Correct some additional compile-related issues.
Move include/nuttx/binfmt/builtin.h to include/nuttx/lib/builtin.h. Move apps/builtin/lib_builtin_forindex.c to libs/libc/builtin/lib_builtin_forindex.c.
Move binfmt/libbuiltin to libs/libc/builtin. There are calls made directly from apps/nshlib into this logic and hence, must be part of a library that can be shared between the OS and applications.
boards: cxd56xx: add SCU sensors (2/2)
* boards: cxd56xx: add cxd56_bh1721fvc initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bh1745nuc initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bm1383glv initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bm1422gmv initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bmi160 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_bmp280 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_kx022 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_lt1pa01 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_rpr0521rs initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_sensors initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56: add Backup Log driver
The driver will be used to backup logs on crash.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: add crashlog driver
Add Crashlog driver with support for reset on crash
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move gs2200m initialization
Move the board gs2200m initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move ili9340 initialization
Move the board ili9340 initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: move lpm013m091a initialization
Move the board lpm013m091a initalization to the common board folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: common: typo fixes
HEADER: Updates on file location
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add the sensor initialization for cxd56xx boards in the common board folder
* boards: cxd56xx: apds9930: typo fix
fix apds9930 typos
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_ak09912 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: move cxd56_bmi160 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_apds9930 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: add cxd56_apds9960 initialization
We are adding the sensor initialization for cxd56xx boards in the
common board folder.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: add SCU sensors
* drivers: platform: add Avago APDS9930 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1721FVC Ambient Light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1745NUC Color Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1383GLV/BM1383AGLV Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1422GMV/BM1422AGMV Magnetic Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMI160 Sensor support
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMP280 Barometic Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Kionix KX022/KX122 Acceleration Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Murata LT1PA01 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm RPR0521RS Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: sensors: bmi160: add optional I2C address
Add a menu option for the case when the SDO pin is pulled to VDDIO
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
tools: unix: add support for common board folder
* tools: unix: add support for common board folder
this patch adds support for a common board folder and simplifies the code
and maintenance on boards that share the same code
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* cxd56xx: migration to a common folder
This is the first platform to be migrated to the new common folder
structure.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: add stub drivers folder for later use
* boards: add stub drivers folder for later use
The board/drivers folder is added for future use.
In this folder we should place drives that are platform specific and
depend on HW that is present only on a specific platform.
NOTE: All shared drivers should go to the regular driver folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: shift BOARD_DIR one level up
In preparation for drivers and common folders we are moving the
BOARD_DIR path up one level.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: add drivers/platform symlink
Link the boards/<arch>/<chip>/drivers dir to drivers/platform
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: add platform specifc drivers extension
There are platforms that use specific drivers and we should be able to
include those drivers in the build
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* board: cxd56xx: drivers: add AK09912 driver for SCU
This is a platform specific driver connected on the SCU unit.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
boards/arm/s32k1xx/s32k148evb: Correct linker scripts for the S32K148, Update README files, Hook eht S32K148EVB into the configuration and build system.
arm/s32k1xx/s32k148evb: Verify core and peripheral clocking. It is the same as the S32K146EVB. Fixed one-too-many copy-paste error in both.
boards/arm/s32k1xx/s32k148evb: Correct LED and button pin number for the S32K148EVB.
boards/arm/s32k1xx/s32k148evb: Change all occurrences of 146 to 148.
boards/arm/s32k1xx/s32k148evb: Initial S32K148EVB. Initial commit is just clone of S32K146EVB with file name changes
arch/arm/src/s32k1xx/s32k1xx_lowputc.c: Fix a typo that prevented LPUART1 from working.
arch/arm/src/s32k1xx/s32k1xx_periphclocks.c and related files: Fix yet another case of confusion between pre-decremented and non-decremented divider values. Enforce the rule that dividers are not decremented until the moment they are written into registers.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Fix another problem related to whether a divider is pre-decremented or not. The answer must be the divder values are never pre-decremented. They are decremented just before being written to hardware.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Clean up some bad conditional logic. Precedence of operators problem.
boards/arm/s32k1xx/s32k118evb: Add support for execution out of SRAM. This is helpful for bringup when you want to avoid putting a lethal image in FLASH.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.h: Remove crystal frequency, it is not used.
arch/arm/src/s32k1xx/s32k1xx_wdog.h: Fix a typo in a register name.i
boards/arm/s32k1xx/s32k*evb/configs/nsh/defconfig: Create Motorola SREC output format.
arm: stm32: codestyle fixes
* arm: stm32f0l0g0: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32f7: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32h7: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32l4: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
s32k1xx/s32k146evb/scripts/flash.ld: Update the linker script for the S32K146.
boards/: Hook the S32K146EVB into the configuration and build system.
s32k146_clockconfig.c: Add S32K146 clock configuration.
boards/arm/s32k1xx/s32k146evb/src/s32k146_periphclocks.c: Update peripheral clocking for the S32K146.
arm/s32k1xx/s32k146evb: Initial support fo S32K146EVB. Starting point is just the S32K118EVB with name changes.
boards/arm/s32k1xx/s32k118evb/include/board.h: Add LPUART0 pin disambiguation.
arch/arm/src/s32k1xx/hardware: Add pin mux definitions for S32K116, 118, 142, 144, 146, and 148.
arch/arm/src/s32k1xx/s32k1xx_pin.c and .h: Add support for PIDR register that disables a gneral purpose pin from acting as an input.
arch/arm/src/s32k1xx/s32k1xx_pin.c and .h: The device does not support slew rate controls or open drain (on all the pins). Only pins that are configured for a protocol that requires open-drain (e.g;, LPI2C, LPUART single-wire) will work in open-drain mode.
Finishes peripheral clock initialization:
arch/arm/src/s32k1xx/s32k11x/s32k11x_clockmapping.c
arch/arm/src/s32k1xx/s32k14x/s32k14x_clockmapping.c
Provide MCU-specific mapping of clock names to PCC control registers.
boards/arm/s32k1xx/s32k118evb/src/s32k118_periphclocks.c
Provides initial clocking for for the S32K118EVB
arch/arm/src/s32k1xx/s32k1xx_periphclocks.c: Add logic to initialize peripheral clocking.
arch/arm/src/s32k1xx/s32k1xx_clockconfig.c: Add SIM clock configuration.
stm32h7 RTC and friends support
* stm32h7:Removed f7 in file path
* stm32f7:Fix overwritten IRQ enabled
System boot order calls clock_initialize then up_initalize.
clock_initialize was setting up the alarm IRQ
up_initalize is initializing the NVIC.
This most likely worked in the past due to a bug in the
NVIC init code that failed to clear the Interrupt enables.
That was fixed in 510b0f7e arch/arm/src: Correct all ARMv7-M
architectures. Interrupts were not be disabled correctly
on power up.
* stm32h7:Ported over F7 RTC
* nucleo-h743zi:Add RTC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arm: sam & tiva: codestyle fixes
* arm: samd2l2: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: samd5e5: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: samv7: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: tiva: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arm: sam34: codestyle fixes
* arm: sam34: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: sama5: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Squashed commit of the following:
boards/arm/s32k1xx/s32k118evb/configs/nsh: Add a basic NSH configuration.
boards/arm/s32k1xx/s32k118evb/scripts: Add linker scripts and Make.defs.
configs/: Hook the S32K118EVB board into the configuration system.
boards/arm/s32k1xx/s32k118evb: Add initial support for the NXP S32K118EVB.
arm: codestyle fixes 4
* arm: max326xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: moxart: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: nrf52: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: nuc1xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: xmc4: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: tms570: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: str71x: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arm: codestyle fixes 3
* arm: lpc214x: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lpc2378: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lpc31xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lpc54xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lpc43xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arm: codestyle fixes 2
* arm: kl: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lc823450: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: lpc17xx_40xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arm: codestyle fixes 1
* arm: a1x: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: am335x: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: c5471: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: cxd56xx: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: dm320: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: efm32: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: imx6: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: imxrt: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: kinetis: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* Revert "Merged in yanqil-br/feature-multi_chan_pwm (pull request #973)"
This reverts commit aef0e0b538.
* arch/arm/src/{stm32/stm32f7/stm32h7/stm32l4}/stm32_pwm.c: configure multi-channel duty only if channel specified. This allows you to update duty cycle for a single channel
* nucleo-f303re/configs: add basic NSH configuration
* nucleo-f303re/configs/pwm: enable console on UART2 and set entry point to nsh_main
Approved-by: Gregory Nutt <gnutt@nuttx.org>
codestyle fixes
* misoc: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* or1k: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* renesas: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* risc-v: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sim: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* x86: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xtensa: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z16: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
avr: hc: mips: codestyle fixes
* avr: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* hc: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mips: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
group boards based on chip
* a1x: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* am335x: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* c5471: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* scx56xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* dm320: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* efm32: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imx6: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imxrt: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* kinetis: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* kl: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lc823450: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc17xx_40xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc214x: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc2378: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc31xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc43xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc54xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* max326xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* moxart: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nrf52: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nuc1xx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam34: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd2l2: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd5e5: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samv7: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f0l0g0: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f7: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32h7: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l4: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* str71x: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tiva: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tms570: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xmc4: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* p112: typo fix
this boars is a z80 board and was moved to the wrong arch
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* avr: at32uc3: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* avr: at90usb: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* avr: atmega: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* hc: mcs92s12ne64: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mips: pic32mx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mips: pic32mz: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* misoc: lm32: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* or1k: mor1kx: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* renesas: m32262f8: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* renesas: sh7032: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* risk-v: gap8: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* risk-v: nr5m100: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sim: sim: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* x86: qemu: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xtensa: esp32: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z16: z16f2811: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80: ez80: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80: z180: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80: z80: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80: z8: group boards based on chip
All boards based on the same chip are moved to the same folder
following the arch layout <arch>/<chip>/<board>.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: update tools for boards based on chip
This patch updates only the linux tools
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pcduino-a10: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* beaglebone-black: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* c5471evm: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* spresense: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ntosd-dm320: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* efm32-g8xx-stk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* efm32gg-stk3700: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-efm32g880f128-stk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sabre-6quad: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imxrt1050-evk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imxrt1060-evk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k28f: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k64f: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k66f: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* kwikstik-k40: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* teensy-3.x: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* twr-k60n512: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* twr-k64f120m: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-kl25z: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-kl26z: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* teensy-lc: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lc823450: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lincoln60: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4088-devkit: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4088-quickstart: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpcxpresso-lpc1768: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mbed: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mcb1700: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc1766stk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* open1788: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pnev5180b: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* u-blox-c027: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* zkit-arm-1769: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mcu123-lpc214x: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* zp214xpa: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc2378: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ea3131: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ea3152: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc-h3131: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* bambino-200e: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4330-xplorer: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4337-ws: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4337-evb: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4370-link2: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpcxpresso-lpc54628: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* max32660-evsys: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* moxa: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nrf52-generic: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nutiny-nuc120: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arduino-due: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* flipnclick-sam3x: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam3u-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4cmp-db: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4e-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4l-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4s-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4s-xplained-pro: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d2-xult: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d3-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d3x-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d4-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd20-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd21-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* saml21-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* metro-m4: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* same70-xplained: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* same71-xult: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* axoloti: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* clicker2-stm32: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* cloudctrl: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* fire-stm32v2: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* hymini-stm32v: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* maple: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mikroe-stm32f4: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f103rb: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f207zg: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f302r8: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f303re: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f303ze: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f334r8: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f410rb: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f446re: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f4x1re: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-1152re: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-e407: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-h405: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-h407: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p107: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p207: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p407: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* omnibusf4: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* photon: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* shenzou: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3210e-eval: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3220g-eval: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3240g-eval: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32_tiny: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32butterfly2: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f103-minimum: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f334-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f3discovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f411e-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f429i-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f4discovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32ldiscovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32vldiscovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* viewtool-stm32f107: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* b-l072z-lrwan1: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f072rb: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f091rc: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f071rg: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l073rz: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f051-discovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f072-discovery: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-144: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f746-ws: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f746g-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f746g-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-h743zi: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* b-l475e-iot01a: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l432kc: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l432re: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l476rg: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l496zg: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l476-mdk: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l476vg-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l4r9ai-disco: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-strp711: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* dk-tm4c129x: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* eagle100: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ekk-lm3s9b96: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-cc1310: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-cc1312r1: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s6432-s2e: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s6965-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s8962-ek: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm4f120-launchpad: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm4c123g-launchpad: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm4c1294-launchpad: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-tms57004: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tms570ls31x-usb-kit: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xmc4500-relax: defconfig update
add ARCH_CHIP to defconfig
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* zp214xpa: typo fix
add missing tools/oocd.sh
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
group boards by architecture
* z80: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z16: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xtensa: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* x86: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sim: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* risc-v: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* renesas: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* or1k: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* misoc: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mips: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* hc: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* avr: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: group boards by architecture
all boards that share the same architecture are moved to the same arch
folder following the soc layout
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: group boards by architecture
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
The legacy '/' delimiter is still supported but not recommend and not advertised.
Squashed commit of the following:
Update configurations instructions in more README.txt files to show ':' delimiter vs '/' delimiter.
Update configurations instructions in various README.txt file to show ':' delimiter vs '/' delimiter.
tools: Update all configuration-related tools to accept ':' separator between board and configuration name.
move board configs to configs folder
* amber: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arduino-due: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arduino-mega: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* avr32dev1: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* axoloti: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* b-l072z-lrwan1: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* b-l475e-iot01a: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* bambino-200e: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* beaglebone-black: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* c5471evm: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* clicker2-stm32: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* cloudctrl: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* demo9s12ne64: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* dk-tm4c129x: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ea3131: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ea3152: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* eagle100: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* efm32-g8xx-stk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* efm32gg-stk3700: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ekk-lm3s9b96: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* esp32-core: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ez80f910200kitg: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ez80f910200zco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* fire-stm32v2: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* flipnclick-pic32mz: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* flipnclick-sam3x: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k28f: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k64f: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k66f: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k125z: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* freedom-k126z: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* gapuino: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* hymini-stm32v: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imxrt1050-evk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* imxrt1060-evk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* kwikstik-k40: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-cc1310: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-cc1312r1: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* launchxl-tms57004: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lc823450-xgevk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lincoln60: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s6432-s2e: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s6965-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm3s8962-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lm4f120-launchpad: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4088-devkit: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4088-quickstart: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4330-xplorer: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4337-ws: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4357-evb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpc4370-link2: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpcxpresso-lpc1768: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* lpcxpresso-lpc54628: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* makerlisp: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* maple: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* max32660-evsys: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mbed: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mbc1700: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mcu123-lpc214x: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* metro-m4: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* micropendous3: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mikroe-stm32f4: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* mirtoo: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* misoc: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* moteino-mega: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* moxa: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ne64badge: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nr5m100-nexys4: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nrf52-generic: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ntosd-dm320: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-144: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f072rb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f091rc: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f103rb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f207zg: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f302r8: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f303re: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f303ze: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f334r8: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f410rb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f446re: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-f4x1re: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-g071rb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-h743zi: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l073rz: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l152re: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l432kc: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l452re: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l476rg: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nucleo-l496zg: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* nutiny-nuc120: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-efm32g880f128-stk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc-h3131: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc1766stk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-lpc2378: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-e407: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-h405: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-h407: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p107: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p207: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-stm32-p407: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimex-strp711: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* olimexino-stm32: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* omnibusf4: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* open1788: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* or1k: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* p112: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pcduino-a10: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* photon: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pic32mx-starterkit: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pic32mx7mmb: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pic32mz-starterkit: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* pnev5180b: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* qemu-i486: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sabre-6quad: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam3u-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4cmp-db: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4e-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4l-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4s-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sam4s-xplained-pro: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d2-xult: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d3-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d3x-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sama5d4-ek: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd20-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samd21-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* same70-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* saml21-xplained: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* samv71-xult: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* shenzhou: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sim: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* skp16c26: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* spresense: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3210e-eval: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3220g-eval: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm3240g-eval: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32_tiny: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32butterfly2: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f051-discovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f072-discovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f103-minimum: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f334-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f3discovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f411e-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f429i-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f4discovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f746-ws: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f746g-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32f769i-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l476-mdk: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l476vg-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32l4r9ai-disco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32ldiscovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* stm32vldiscovery: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* sure-pic32mx: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* teensy-2.0: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* teensy-3.x: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* teensy-lc: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tm4c123g-launchpad: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tm4c1294-launchpad: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tms570ls31x-usb-kit: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* twr-k60n512: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* twr-k64f120m: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* u-blox-c027: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* ubw32: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* viewtool-stm32f107: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* us7032evb1: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* xmc4500-relax: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z16f2800100zcog: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z80sim: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z8encore000zco: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* z8f64200100kit: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* zkit-arm-1769: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* zp214xpa: move board configs to configs folder
This is a cleanup that will move all configs from the board folder to
a board/configs folder
NOTE:
The configure.sh script must be used with the new path <board-name>/configs/<config-name>
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: configure.sh: adjust the script to use boards/configs folder
Script update to pick the configs from the new configuration folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: configure.bat: adjust the script to use boards/configs folder
Now we update the script to pick the configs from the new configuration folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
