Intel64 can now boot application cores which is needed for SMP
IMPORTANT: CONFIG_BOARD_LOOPSPERMSEC must be properly configured,
otherwise AP boot sequence can fail due too short delays during the AP startup
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Add support for inter-processor signaling in x86_64 based on up_trigger_irq() interface.
Preparations for SMP.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
reduce the time consumed by function call
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Use GS base regsiter to store reference to CPU private data.
Then we can easily refer to private CPU data using the GS segment.
Required for SMP support.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
It turns out that the D0 core of the BL808 has an IRQ that represents all interrupt sources for the M0 core. This change uses this IRQ to access these sources, eliminating the need for IPC between M0 and D0.
fix missing reference to comm_region->tsc_khz and
fix 'defined but not used' warnings in arch/x86_64/intel64_rtc.c
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
Hide --whole-archive behind Kconfig option for x86.
This option is not needed and breaks ELF modules build.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
on ACRN hypervisor obtaining frequency from CPUID seems to be broken,
so we have to specify this value from Kconfig.
If frequency autodetection is enabled but the returned data are
incorrect - crash early.
Signed-off-by: p-szafonimateusz <p-szafonimateusz@xiaomi.com>
- This PR adds the GPIO Driver for BL808 SoC. This will be used by the upcoming LED Driver for Ox64 Board.
- The BL808 GPIO Driver was derived from the NuttX Driver for BL602 GPIO
Co-Authored-By: Lup Yuen Lee <luppy@appkaki.com>
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
For now, IOB off-loading in the wireless driver was removed because
it is not compatible with SMP-enabled devices, which is valid for
ESP32-S3. The performance gain by keeping the IOB off-loading in
the wireless drivers is not exceeded by keeping the flat buffer
approach and enabling `CONFIG_SMP=y`.
This commit modifies the existing serial driver to add support for the remaining UARTs on the BL808. It also introduces support for setting baud rate, character length, stop bits, parity, flow control and which serial port acts as the console.
Use `nxsched_gettid` instead of `nxsched_getpid`. Previously each
kernel thread was modelled as a task, so the pid is the same of the
kthread id. Now, with shared kthread group (introduced by #12320),
the pid of all kthreads will be 0 by design in shared group.
This change implements a system for allowing the D0 core (which runs NuttX) to receive forwarded interrupts from the M0 core. This makes it possible for drivers that rely on interrupts to work with peripherals attached to the M0 core.
cpu0 cpu1:
user_main
signest_test
sched_unlock
nxsched_merge_pending
nxsched_add_readytorun
up_cpu_pause
arm_sigdeliver
enter_critical_section
Reason:
In the SMP, cpu0 is already in the critical section and waiting for cpu1 to enter the suspended state.
However, when cpu1 executes arm_sigdeliver, it is in the irq-disabled state but not in the critical section.
At this point, cpu1 is unable to respond to interrupts and
is continuously attempting to enter the critical section, resulting in a deadlock.
Resolve:
adjust the logic, do not entering the critical section when interrupt-disabled.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
As suggested in PR:12530, changed the default names of ESP32S3WROOM chips to ESP32S3WROOM1N4,
ESP32S3WROOM2N16R8, ESP32S3WROOM2N32R8, ESP32S3MINI1N8.
Also regenerated all the defconfigs for board configurations.
Added a custom ESP32S3 module for custom flash configurations.
Declared ESP32S3_PSRAM_8M variable with prompt
we can use g_cpu_lockset to determine whether we are currently in the scheduling lock,
and all accesses and modifications to g_cpu_lockset, g_cpu_irqlock, g_cpu_irqset
are in the critical section, so we can directly operate on it.
test:
We can use qemu for testing.
compiling
make distclean -j20; ./tools/configure.sh -l qemu-armv8a:nsh_smp ;make -j20
running
qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic -machine virt,virtualization=on,gic-version=3 -net none -chardev stdio,id=con,mux=on -serial chardev:con -mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
- In some cases, an operational Ethernet MAC may have no PHY, for example
when the system has a direct RMII MAC-to-MAC link.
- New config option STM32H7_NO_PHY
- With this option, PHY-specific code in the ethernet driver is not built
- This option is inherently incompatible with autonegotiation and speed and
duplex settings must be compiled in
To simplify processing, the existed SBI function code is just
invoking the ecall and return the error value. This omits
potential return value in "a1", which is defined in SBI doc.
Add the "sbiret" struct so it can handle all the return value.
In addition, there are some minor improvement:
1. move the SBI related interface to a separate file to make it clean.
2. add all necessary SBI ecall interface macro until version 2.0.
3. add an utilty function to convert sbi error numner to standard
error number.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
