This reverts commit 45672c269d.
Because:
* It's very confusing to have cc as LD.
* I don't see what "-nostartfiles -nodefaultlibs" in LDFLAGS are
supposed to do when we use LD directly. It would be simpler to
remove them from our LDFLAGS.
Verge Aero has submitted the SGA
Anthony Merlino has submitted the SGA
Gregory Nutt has submitted the SGA
Sebastien Lorquet has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
This commit removes the initialization of the Wi-Fi partition
from the Wi-Fi board logic and moves it to the SPI Flash board code.
It creates 2 different partition (one for Wi-Fi and one for general
use).
It also allows these partitions to be mounted over several FSs.
When SIM_SPI is valid, a specified Linux SPI device ‘spidevN.P’(N is bus number and P is CS number) is attached to nuttx simulator, shown as 'spi0' under /dev. One may type spi command (need SPITOOL valid) in NSH to control the Linux SPI and exchange data, other devices such sensors can use it to debug in simulator on a Ubuntu PC. Note that a USB<>SPI module (e.g. CH341A/B) should be plugged in to achieve Linux SPI ports.
Change-Id: I275b2c2bbf6d14bcdf514c89efb9a2264d69e9a3
Signed-off-by: liucheng5 <liucheng5@xiaomi.com>
several configs are used for testing and need the BSD components
more information about license can be found here
https://www.apache.org/legal/resolved.html#category-a
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
several configs are used for testing and need the BSD components
more information about license can be found here
https://www.apache.org/legal/resolved.html#category-a
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
several configs are used for testing and need the BSD components
more information about license can be found here
https://www.apache.org/legal/resolved.html#category-a
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
This commit adds option for Teensy 4.x board to initialize CAN3 as can0.
The reason of this is the CAN FD capability of CAN3. This commit also
disables tickless mode support for pikron-bb configuration as this option
started causing hard faults which are yet to be solved.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
By default the components with BSD license should be disabled
NOTE:
the BLUETOOTH components was enabled in a non bluetooth config
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
By default the Bluetooth configuration is disabled due to BSD license
Please enable the use of BSD licenses and the Bluetooth config
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
By default the components with BSD license are disabled.
NOTE:
We are making an exception and enable the BSD components for
Simulator build to be able to thest the functionality.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Add a driver for CorePWM block, which can be instantiated on PolarFire SOC FPGA
This supports 2 CorePWM blocks on the FPGA. One CorePWM block provides 8 PWM output signals
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Alan Carvalho de Assis has submitted the ICLA
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
When trying to reproduce a reported issue with telnetd,
it took me a bit to find out a working config with telnetd.
I don't want to repeat the process again in future.
OTOH, I don't feel it's worth to have a separate config for this.
Enable a few things convenient for testing network stuff
- telnetd
- iperf
- NET_STATISTICS
- Bump NET_NACTIVESOCKETS
Stack related
- Enable interrupt stack
- Tweak stack sizes
- STACK_COLORATION
- SYSTEM_STACKMONITOR
Debug stuff
- Enable assertions
- Enable some WARN/ERROR logs
Misc
- Disable C++ as it does nothing for the rest of the config and
it's expensive (involving a download of the library)
Summary:
- I noticed that the RNDIS networking is unstable when running
nxplayer + command execution via telnet
- This commit is a workaround to fix this issue by disabling
CONFIG_TCP_WRITE_BUFFERS. Also, CONFIG_SENDFILE_BUFSIZE is
increased to improve the webserver performance.
Impact:
- spresense:rndis_smp only
Testing:
- Tested with nxplayer, telnetd and webserver
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This command enables the application to perform the final steps of the
booting process prior to finally switching the execution to another
firmware image.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
Summary:
- This commit adds RTC and NTP client to wapi_smp/defconfig
Impact:
- None
Testing:
- Tested with ntpcstart & date
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Currently the "esp32_spiflash_alloc_mtdpart" allocates a
statically-defined partition from "offset" and "size" set via
Kconfig.
This commit changes the function interface to receive those information
as arguments, enabling the creation of multiple MTD partitions with
different offsets and sizes.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
so the source code compiled by host environment can include config.h
directly and then avoid pass Kconfig option through Makefile manually
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ic9fe6f846082cef2d0808dc717df8ae6ed929edf
BOARDIOC_SWITCH_BOOT is required to communicate the boot partition from
userspace (OTA subsystem) to board. It can be used to change the system
boot behavior. So it's useful for A/B boot or even single boot case.
For the board support A/B boot case:
1. Download the new image from the sever
2. Write the new image to the alternative partition
3. Call BOARDCTL_SWITCH_BOOT to the alternative system
For single boot partition case:
1. Download the new image from the sever
2. Call BOARDCTL_SWITCH_BOOT and reboot to a small system
3. Write the new image to the main partition in the small system
4. Call BOARDCTL_SWITCH_BOOT again to the main system
Change-Id: Ifebb495784ecf06842946a249bec64f75dce894f
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
The patch
Make: use gcc as LD
introduced use of GCC wrapper as linker. LD variable references GCC
executable now. But when GCC wrapper s used to build relocatable
loadable objects (ELF executables and modules) then it causes
linking of toolchain default libc and other libraries even when -r
is usd. Another problem is that incorrect multiarch variant is selected
for libraries search and possibly even for LTO or C++ templates
instantiating and other glue code which causes fails during linking
if CFLAGS selects non/default miltiarch variant.
Corresponding CFLAGS are passed to LDMODULEFLAGS and LDELFFLAGS
as well as -nostartfiles -nodefaultlibs options.
Separate line is used to easily find and adjust lines if link
process is changed in future.
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
Gregory Nutt has submitted the SGA
Zilogic Systems has submitted the SGA
Uniquix Tecnologia has submitted the SGA
Michael Jung has submitted the ICLA
Alan Carvalho de Assis has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
the common scripts.
This allows having a more costumized linker script per board.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
1. Added check for repeated connection wifi operations.
2. Invoke the carrier on/off operation in the wrong place.
3. The RTC initialization time is incorrect.
4. Reserve 32K I-Cache space in the linker script.
5. Increase the size of the wifi firmware receiving buffer.
Signed-off-by: Virus.V <virusv@live.com>
ld: /github/workspace/sources/nuttx/nuttx section `.data' will not fit in region `locked'
ld: section .paged LMA [0000000011034000,0000000011040fa3] overlaps section .data LMA [0000000011033ff4,00000000110340e3]
ld: region `locked' overflowed by 228 bytes
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- This commit adds CONFIG_NET_TCP_WRITE_BUFFERS=y to
rndis and rndis_smp defconfigs
Impact:
- webserver performance will be improved
Testing:
- Tested with nxplayer, telnetd, webserver, iperf
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds the following to smp/defconfig
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_STACK_COLORATION=y
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit removes SMP features from nsh/defconfig
because it's still unstable
Impact:
- None
Testing:
- None
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
to avoid the follow link error:
ld: /github/workspace/sources/nuttx/nuttx section `.data' will not fit in region `flash'
ld: region `flash' overflowed by 4 bytes
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Summary:
- I noticed that spresense:rndis_smp and spresense:wifi_smp
do not boot due to the recent change in nx_start.c
- As the result of the discussion, I understand that we have to
add CONFIG_BOARD_LATE_INITIALIZE=y for SMP
Impact:
- spresense only
Testing:
- Tested with spresense:rndis_smp and spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
Summary:
- I noticed that Telnet session is sometimes not closed
when tested with nxplayer + command stress test
- The symptom relates to the change of IOB throttling in TCP
but we are still finding the root cause.
- This commit is just a workaround to avoid the issue by
disabling telnet character mode.
Impact:
- spresense:rndis, spresense:rndis_smp only
Testing:
- Tested with nxplayer (HTTP audio streaming) + command stress test
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
regions.
With this we also don't need two separate linker scripts (one for IRAM
and another one for FLASH). Only one linker script (now called
esp32.ld) is now present.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
This memory region can be accessed by both I & D buses, so the heap can
be used for data storage and code execution.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
corrected setting SDMMC_DCTRL.DTMODE field for block data transfers ending on block count
and for block data transfers ending with STOP_TRANSMISSION command;
stm32_sdio: added more debug messages
section.
The RTC region is accessed by both I and D buses. The old name of
`rtc_iram_seg` is a bit confusing.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Laurent Latil has submitted the ICLA
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- This commit adds the following configs to spresense:elf
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_STACK_COLORATION=y
Impact:
- None
Testing:
- Tested with spresense
Signed-off-by: Masayuki Ishikawa <masayuki.ishikawa@gmail.com>
Many device driver will call the host API to finish the simulation
which require the big stack in the most case, so let's utilize the
new DEFAULT_TASK_STACKSIZE(64KB on sim) option instead.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Gregory Nutt is has submitted the SGA
Michal Lyszczek has submitted the ICLA
as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
SPI0 is used for the connection of the LCD controller.
Additional SPI and GPIO signals definitions:
SPI0_NPCS1 - SPI Chip Select, PD25
GPIO_LCD_CD - Command/Data, pin PB2
GPIO_LCD_RST - Reset, pin PB3
boards/arm/samv7/samv71-xult/src/sam_st7789.c is
derived from boards/arm/imxrt/teensy-4.x/src/imxrt_st7789.c
Signed-off-by: Jaroslav Beran <jara.beran@gmail.com>
Summary:
- This commit converts data to the physical address for DMA transfer.
Impact:
- cxd56_imageproc.c and cxd56_audio_dma.c
Testing:
- Not tested
Signed-off-by: Kazuya Hioki <Kazuya.Hioki@sony.com>
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- In order to support the atomic instructions by ldrex/strex instruction
in NuttX SMP, the data or later sections are mapped to the system bus.
Impact:
- Bootloader for Spresense SDK 2.1.0 or later must be installed
- Loops per msec must be adjusted
- Physical address for DMA must be converted with CXD56_PHYSADDR
Testing:
- Will be tested with later commits
Signed-off-by: Kazuya Hioki <Kazuya.Hioki@sony.com>
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
by EXTRAFLAGS. This was supposed to be part of an old PR but this board
was left behind.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Summary:
- This commit removes CONFIG_LIBM from defconfigs to use libm for gcc
Impact:
- Applications which use the math library
Testing:
- Tested with spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
If the GPIO falls within 300us after raising
(or GPIO raises within 300us after falling), the modem may miss the GPIO
interrupt. So add delay by 300us before changing the GPIO.
When CONFIG_BOARD_RESET_ON_ASSERT is enabled, board_reset() may be
called on interrupt context. This commit changes to be able to call the
function on interrupt context.
Drop to user-space in kernel/protected build with up_pthread_exit,
now all pthread_cleanup functions executed in user mode.
* A new syscall SYS_pthread_exit added
* A new tcb flag TCB_FLAG_CANCEL_DOING added
* up_pthread_exit implemented for riscv/arm arch
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
Summary:
- This commit adds ELF support to netnsh and netnsh_smp
Impact:
- None
Testing:
- Tested with QEMU
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
specified the name of remote proc(rpmsg server)
Change-Id: I0086bb43727a2bbb5e68f88907b5e4608182ef9c
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
N/A
specified the name of remote proc(rpmsg server)
Change-Id: Ie270d651071e87a40a80ab489597ae18db9814f0
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
Summary:
- This commit fixes the warnings reported by the CI
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit adds maix-bit:smp2 configuration to test different
sched parameters such as CONFIG_SCHED_CHILD_STATUS=y
Impact:
- None
Testing:
- Tested with ostest
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- The CONFIG_SMP_IDLETHREAD_STACKSIZE was introduced to optimize
the idle stack size for other than CPU0
- However, there are no big differences between the idle stacks.
- This commit removes the config to simplify the kernel code
Impact:
- All SMP configurations
Testing:
- Tested with ostest with the following configs
- spresense:smp, spresense:rndis_smp
- esp32-devkitc:smp (QEMU), maix-bit:smp (QEMU)
- sabre-6quad:smp (QEMU), sabre-6quad:netnsh_smp (QEMU)
- raspberrypi-pico:smp, sim:smp (x86_64)
Signed-off-by: Masayuki Ishikawa <asayuki.Ishikawa@jp.sony.com>
This config is only useful when there is a > 4MB PSRAM and thus needs to
be selected by the user explicitly.
Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
Summary:
- This is just a workaround to avoid a crash in signest_test
- The commit should be reverted once we find the root cause of the issue
Impact:
- None
Testing:
- Tested with ostest
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
arch: Allocate the space from the beginning in up_stack_frame
and modify the affected portion:
1.Correct the stack dump and check
2.Allocate tls_info_s by up_stack_frame too
3.Move the stack fork allocation from arch to sched
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This adds initializing for the following sensor types:
- HYT271 humidity and temperature sensor
- DS18B20 temperature sensor
Signed-off-by: Marco Krahl <ocram.lhark@gmail.com>
All supported arch uses a push-down stack:
The stack grows toward lower addresses in memory. The stack pointer
register points to the lowest, valid working address (the "top" of
the stack). Items on the stack are referenced as positive(include zero)
word offsets from sp.
Which means that for stack in the [begin, begin + size):
1.The initial SP point to begin + size
2.push equals sub and then store
3.pop equals load and then add
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Janne Rosberg has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Ivan Ucherdzhiev has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Ken Pettit has submitted the ICLA and we can migrate the licenses
to Apache.
Sebastien Lorquet has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Marco Krahl has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt, S.A has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Philippe Coval has submitted the ICLA and we can migrate the licenses
to Apache.
Alan Carvalho de Assis has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt, S.A has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
The GPIO_LEDx are already used by esp32_userleds.c, they shouldn't
be used by esp32_gpio.c. This patch also includes the GPIO Input
example (GPIN) that was missing.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Mateusz Szafoni has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Actia Nordic AB has submitted the SGA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Several licenses were missed in the initial work
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Added a simple defconfig to support the userled driver and its application
for testing in the nsh.
Signed-off-by: Gustavo L F Walbon <gwalbon@linux.ibm.com>
Since 7a046358d9 the top-level COPYING
file has been deleted and replaced by DISCLAIMER, LICENSE, and NOTICE
files. However, some references to the old COPYING file remained in
Kconfig help text and documentation.
Documentation/contributing/coding_style.rst:
Documentation/introduction/about.rst:
boards/arm/lpc17xx_40xx/olimex-lpc1766stk/README.txt:
boards/arm/sam34/arduino-due/README.txt:
boards/arm/sam34/sam4l-xplained/README.txt:
boards/arm/sama5/giant-board/README.md:
boards/arm/sama5/sama5d2-xult/README.txt:
boards/arm/sama5/sama5d4-ek/README.txt:
boards/arm/samd2l2/samd20-xplained/README.txt:
boards/arm/samd2l2/samd21-xplained/README.txt:
boards/arm/samd2l2/saml21-xplained/README.txt:
boards/arm/stm32/hymini-stm32v/README.txt:
boards/arm/stm32/stm3210e-eval/README.txt:
fs/fat/Kconfig:
libs/libc/string/Kconfig:
* Updates stale references to the old top-level COPYING file to
either LICENSE or NOTICE (or both), as appropriate in each
instance.
Laurent Latil has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Gwenhael Goavec has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidranec has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Jacob Dahl has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Bob Feretich has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Goden Freemans has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Ivan Petrov Ucherdzhiev has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Petro Karashchenko has submitted the ICLA and we can migrate the licenses
to Apache.
Ivan Petrov Ucherdzhiev has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Neil Hancock has submitted the ICLA and we can migrate the licenses
to Apache.
Mateusz Szafoni has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Max Holtzberg has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Michael Jung has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Mateusz Tomasz Szafoni has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Abdelatif Guettouche has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
lpc17_40_userleds.c: Adds the support of Userleds driver which
provides a device to manipulate the 4 leds of the board through the
/dev/userleds.
lpc17_40_leds.c: Removes not used definitions, eg. MBED_LED3_ON.
Board LED Status support(CONFIG_ARCH_LED=y) and Device Drivers/Led
Support(CONFIG_ARCH_USERLED=y) can not be enable together.
Signed-off-by: Gustavo L F Walbon <gwalbon@linux.ibm.com>
Normally, statically allocated data goes in .bss, followed by the
initial stack, followed by HEAP. However, any data that is statically
allocated in SRAM4 with __attribute__ ((section (".sram4"))) will
clobber, and be clobbered by, the HEAP.
On STM32H7, BDMA can only access SRAM4. Therefore any BDMA buffers (or
any other data) placed in SRAM4 will expose this problem. In one case,
this manifested as a failure of NSH to start, because the SPI6 BDMA
buffers clobbered the /dev/console inode structs, which the OS
allocated earlier.
This PR ensures that only the rest of SRAM4, after any static data, is
added to the heap. This PR also allows SRAM4 to be completely excluded
from the heap by a new Kconfig, CONFIG_STM32H7_SRAM4EXCLUDE, similar
to what CONFIG_STM32H7_DTCMEXCLUDE does for the DTCM region.
Change required in linker scripts:
Every STM32H7 linker script must replace this:
.sram4 :
{
} > sram4
with this:
.sram4_reserve (NOLOAD) :
{
*(.sram4)
. = ALIGN(4);
_sram4_heap_start = ABSOLUTE(.);
} > sram4
or link will fail with: undefined reference to '_sram4_heap_start'.
The Release Notes should document this for users with out-of-tree
boards.
arch/arm/src/stm32h7/Kconfig:
* Add config STM32H7_SRAM4EXCLUDE to allow excluding all of SRAM4
from the HEAP.
arch/arm/src/stm32h7/stm32_allocateheap.c:
* Only when including SRAM4 in the heap, define HAVE_SRAM4,
SRAM4_START, SRAM4_END, and SRAM4_HEAP_START.
* Add "Private Data" section.
* Add extern for_sram4_heap_start, which must be defined in the
board's linker script.
* arm_addregion(): Only add SRAM4 to the heap when configured to
do so, i.e., unless CONFIG_STM32H7_SRAM4EXCLUDE is defined, and
only add the portion of SRAM4 that is past any static data.
boards/arm/stm32h7/nucleo-h743zi/scripts/flash.ld:
boards/arm/stm32h7/nucleo-h743zi/scripts/kernel.space.ld:
boards/arm/stm32h7/nucleo-h743zi2/scripts/flash.ld:
boards/arm/stm32h7/stm32h747i-disco/scripts/flash.ld:
boards/arm/stm32h7/stm32h747i-disco/scripts/kernel.space.ld:
* Update all in-tree STM32H7 board linker scripts as described in
"Change required in linker scripts" above.
Testing:
* Successfully built all of the following configurations:
nucleo-h743zi2:jumbo
nucleo-h743zi2:nsh
nucleo-h743zi:nxlines_oled
nucleo-h743zi:elf
nucleo-h743zi:otg_fs_host
nucleo-h743zi:nsh
nucleo-h743zi:netnsh
nucleo-h743zi:pwm
stm32h747i-disco:nsh
* Tested with custom board.
* nxstyle.
References:
[1] See the dev@nuttx.a.o mailing list discussion started 2021/03/25:
"How to ensure HEAP will not overlap static DMA buffer?"
https://lists.apache.org/thread.html/recf2bb9043f8c9f53c10917e2adb2ec64fe35dc5e6f9a695a7ac6ecc%40%3Cdev.nuttx.apache.org%3E
[2] See arm_addregion() in arch/arm/src/stm32h7/stm32_allocateheap.c
Thanks to Gregory Nutt and David Sidrane for suggestions and reviews.
