Adds an initial Nuttx audio driver supporting the Spresense CXD56.
Being a work in progress the driver has a number of limitations:
- Audio playback only, no recording yet.
- Only 16 bit stereo playback is supported.
- In practice only 48kHz playback is supported due to missing SRC.
lpc2148_spi1.c:142:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type 'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
142 | .send = spi_send,
| ^~~~~~~~
lpc2148_spi1.c:142:24: note: (near initialization for 'g_spiops.send')
In file included from ieee802154/mac802154_bind.c:49:
ieee802154/mac802154_internal.h: In function 'mac802154_setdevmode':
ieee802154/mac802154_internal.h:788:42: warning: converting a packed 'enum ieee802154_devmode_e' pointer (alignment 1) to a 'const union ieee802154_attr_u' pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
788 | (FAR const union ieee802154_attr_u *)&mode);
| ^~~~~~~~~~~~~~~~~
chip/stm32_hciuart.c: In function 'hciuart_read':
chip/stm32_hciuart.c:2104:30: warning: statement with no effect [-Wunused-value]
2104 | ntotal == (ssize_t)ret;
| ~~~~~~~^~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_auth_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:579:23: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
579 | type = bcmf_getle32(&event->type);
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:580:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
580 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_scan_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:619:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
619 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:620:35: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
620 | escan_result_len = bcmf_getle32(&event->len);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_bdc.c: In function 'bcmf_bdc_process_event_frame':
wireless/ieee80211/bcm43xxx/bcmf_bdc.c:166:27: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
166 | event_id = bcmf_getle32(&event_msg->event.type);
| ^~~~~~~~~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_direct':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:157:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
157 | ret = SDIO_RECVR5(dev, SD_ACMD52, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_extended':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:239:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
239 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:244:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
244 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:257:7: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
257 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:265:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
265 | SDIO_RECVR1(dev, SD_ACMD52ABRT, (uint32_t *)&resp);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:2860:7: warning: unused variable 'ret' [-Wunused-variable]
2860 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:3044:7: warning: unused variable 'ret' [-Wunused-variable]
3044 | int ret;
| ^~~
chip/stm32_i2c.c:722:12: warning: 'stm32_i2c_sem_wait_noncancelable' defined but not used [-Wunused-function]
722 | static int stm32_i2c_sem_wait_noncancelable(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/gs2200m.c: In function 'gs2200m_read':
wireless/gs2200m.c:727:20: warning: passing argument 1 of 'nxsem_wait' from incompatible pointer type [-Wincompatible-pointer-types]
727 | ret = nxsem_wait(dev);
| ^~~
| |
| struct gs2200m_dev_s *
.config:1207:warning: symbol value '' invalid for TESTING_OSTEST_FPUSIZE
platform/audio/cxd56_audio_analog.c:69:13: warning: inline function 'cxd56_audio_clock_is_enabled' declared but never defined
69 | inline bool cxd56_audio_clock_is_enabled(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:68:13: warning: inline function 'cxd56_audio_clock_disable' declared but never defined
68 | inline void cxd56_audio_clock_disable(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:67:13: warning: inline function 'cxd56_audio_clock_enable' declared but never defined
67 | inline void cxd56_audio_clock_enable(uint32_t clk, uint32_t div);
| ^~~~~~~~~~~~~~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:1348:7: warning: unused variable 'ret' [-Wunused-variable]
1348 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:1496:7: warning: unused variable 'ret' [-Wunused-variable]
1496 | int ret;
| ^~~
chip/stm32_i2c.c:729:12: warning: 'stm32_i2c_sem_wait_uninterruptble' defined but not used [-Wunused-function]
729 | static int stm32_i2c_sem_wait_uninterruptble(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/lpwan/sx127x/sx127x.c:147:52: warning: missing terminating ' character
147 | # warning OOK support is not complete, RX+TX doesn't work yet!
| ^
str71_spi.c:435:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type
'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
435 | .send = spi_send,
| ^~~~~~~~
str71_spi.c:435:24: note: (near initialization for 'g_spiops.send')
chip/pic32mx-lowconsole.c:147:24: warning: 'pic32mx_getreg' defined but not used [-Wunused-function]
static inline uint32_t pic32mx_getreg(uintptr_t uart_base,
^
chip/pic32mx-gpio.c:113:20: warning: 'pic32mx_value' defined but not used [-Wunused-function]
static inline bool pic32mx_value(uint16_t pinset)
^
chip/pic32mz-gpio.c:124:20: warning: 'pic32mz_value' defined but not used [-Wunused-function]
static inline bool pic32mz_value(pinset_t pinset)
^
chip/pic32mx-usbdev.c:3065:1: warning: 'pic32mx_epreserved' defined but not used [-Wunused-function]
pic32mx_epreserved(struct pic32mx_usbdev_s *priv, int epno)
^
mmcsd/mmcsd_spi.c: In function 'mmcsd_mediachanged':
mmcsd/mmcsd_spi.c:1938:7: warning: 'return' with a value, in function returning void
return ret;
^
In file included from partition/fs_partition.c:42:0:
partition/partition.h:66:19: warning: 'read_partition_block' defined but not used [-Wunused-function]
static inline int read_partition_block(FAR struct partition_state_s *state,
^
local/local_netpoll.c: In function 'local_pollsetup':
local/local_netpoll.c:305:1: warning: label 'pollerr' defined but not used [-Wunused-label]
pollerr:
^~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: If3ea8f32b878aa218072130f7c3018f0d3c1aca5
As pointed out by Şükrü Bahadır Arslan in PR765, function calls
inside DEBUGASSERT() will not be executed if DEBUGASSERT is
disabled. Following that PR, I searched for other instances of
similar errors and found four. As there are many thousands of
DEBUGASSERT in the code, this is *not* an exhaustive fix.
arch/arm/src/tms570/tms570_boot.c:
* In function arm_boot(), call tms570_memtest_complete()
outside of the DEBUGASSERT(). Otherwise, if DEBUGASSERT is
disabled, we will never rendezvous with completion of the
test. (Two instances of this fix.)
arch/arm/src/tms570/tms570_clockconfig.c:
* In function tms570_clockconfig(), call
tms570_efc_selftest_complete() outside of the DEBUGASSERT()
for the same reason as above.
boards/arm/sam34/sam4s-xplained-pro/src/sam_boot.c:
* In function board_late_initialize(), call
sam_watchdog_initialize() outside of the DEBUGASSERT() for
the same reason as above.
Modified boards/z80/z180/p112/README.txt and boards/z80/z80/z80sim/README.txt:
IMPORTANT NOTE as of 2020-4-11: Support for CONFIG_CAN_PASS_STRUCTS was removed in NuttX-9.1. This was necessary to enforce some POSIX interface compliance but also means that ALL older SDCC versions will no long build with NuttX. I have been told that the newest SDCC compilers can indeed pass structure and union parameters and return values. If that is correct, then perhaps the newer SDCC compilers will be used. Otherwise, it will be necessary to use some other, more compliant compiler.
So call 'make EXTRAFLAGS=-Wno-cpp' could suppress the warnings with pre-processor
directive #warning in GCC.
Change-Id: Iaa618238924c9969bf91db22117b39e6d2fc9bb6
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
* boards/arm/stm32/nucleo-f429zi: Initial port to nucleo-f429zi board.
* boards/arm/stm32/nucleo-f429zi: Add two demo configs.
* Add the nucleo-f429zi to boards/Kconfig
boards/Kcondig: Fixed line alignment issue.
* boards/arm/stm32/nucleo-f429zi: Change the license header of all new files to an Apache 2.0 license.
* boards/arm/stm32/nucleo-f429zi: nxstyle fixed
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for those files under fs/driver, fs/aio, fs/nfs, crypto/, and boards/.
Please note: The modified file under fs/nfs generates several " Mixed case identifier found" errors. Please ignore these. These cannot be fixed without changes to numerous other files. They also follow a non-standard convention that is used many files: Using lower case structure names in custom SIZEOF_ definitions.
Namely these defconfig files:
boards/sim/sim/sim/configs/mtdpart/defconfig
boards/sim/sim/sim/configs/mtdrwb/defconfig
boards/sim/sim/sim/configs/rpproxy/defconfig
boards/sim/sim/sim/configs/rpserver/defconfig
boards/sim/sim/sim/configs/tcpblaster/defconfig
Because the recent versions of macOS is 64-bit only and thus
incompatible with CONFIG_SIM_M32=y.
The following defconfig files are left intact as these configs
are important for them:
boards/sim/sim/sim/configs/loadable/defconfig
boards/sim/sim/sim/configs/module32/defconfig
Because:
* A raw binary doesn't make sense for sim, where ./nuttx is
a host OS executable.
* It breaks test builds on macOS, where native objcopy
is not available.
* The appropriate size of stack varies among archs.
E.g. for 64-bit sim, 2048 is way too small, especially when the task
happens to use host OS functionalities.
I plan to allow an arch provide its own default.
* I plan to use this to replace hardcoded "STACKSIZE = 2048" in APPDIR.
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
Necessary for dlfcn etc on ESP32, which has separate memory regions
for instruction and data.
known issues/todo
* consider something similar to dual heaps for PROTOECTED
* consider to adapt binfmt as well
boards/z80/ez80/z20x/configs/w25boot/defconfig: Increase size of serial Tx buffer.
boards/z80/ez80/z20x/src/w25_main.c: Add some fflush() in necessary places. Greatly improves the usability of the UI.
boards/z80/ez80/z20x/README.txt: Trival update to README
drivers/serial/serial.c and tcdrain.c: Correct some typos.
- boards/z80/ez80/z20x/scripts/z20x_*.linkcmd: Reduce from 4 to 1 wait state. That i sufficient because of the slow clocking of the eZ80F92
- boards/z80/ez80/z20x/src/w25_main.c: Replace CRC algorithm with simple, less time consuming check sum.
- boards/z80/ez80/z20x/configs/nsh: Rename the nsh_ram configuration to just nsh
- boards/z80/ez80/z80x/configs/hello: Add simpler program to make debugging the loader easier.
I skipped the following files because they were not simple.
I'll create separate PRs.
arch/xtensa/src/esp32/esp32_cpustart.c
arch/xtensa/src/common/xtensa_abi.h
boards/xtensa/esp32/esp32-core/include/board.h
Also, I skipped the following files and directories because
they looked too huge and/or foreign.
arch/xtensa/include/esp32/tie.h
arch/xtensa/include/xtensa/xtensa_corebits.h
arch/xtensa/src/esp32/hardware/
arch/xtensa/include/esp32/tie-asm.h
arch/xtensa/include/esp32/core-isa.h
arch/xtensa/include/xtensa/core.h
I also fixed a few "is is" style typos when unwrapping long lines.
arch/z80/src/ez80/ez80_timerisr.c: Correct a mismatch between the programmed reload value and the timer input clock frequency.
arch/z80/src/ez80/ez80f92.h: Correct error in timer input clock divider: Bits 2-3, not bits 3-4.
boards/z80/ez80/z20x/src/w25_main.c: Correct an uninitialized return value; private function was not declard static.
boards/z80/ez80/z20x/src/w25_main.c: (1) Correct size comparison typo: Should have been >= not != (2) Fix sizeof(): Was ugetting the sizeof the pointer instead of the sizeof the pointed at structure. (3) Improve some comments.
boards/z80/ez80/z20x: Increase RX buffer size to 4Kb, reduce BAUD to 2400 in w25boot configuration
arch/z80/src/ez80/ez80_serial.c: Reduce Rx FIFO trigger level for eZ80F92 to 1 so that will respond more quickly to incoming data.
boards/z80/ez80/z20x/src/w25_main.c: Improve user interface.
There is still an error occurring while downloading Intex HEX files to FLASH. That is unrelated to this and appears to be a problem libs/libc/hex2gbin/lib_hex2bin.c
fix the following warning:
chip/sam_allocateheap.c:120:8: warning: #warning "CONFIG_MM_REGIONS < 3: NFC SRAM not included in HEAP" [-Wcpp]
120 | # warning "CONFIG_MM_REGIONS < 3: NFC SRAM not included in HEAP"
| ^~~~~~~
chip/lpc17_40_allocateheap.c:176:6: warning: #warning "CONFIG_MM_REGIONS > 1: This configuration has no available AHB SRAM Bank0/1" [-Wcpp]
176 | # warning "CONFIG_MM_REGIONS > 1: This configuration has no available AHB SRAM Bank0/1"
| ^~~~~~~
chip/stm32l4_allocateheap.c:141:4: warning: #warning "CONFIG_MM_REGIONS large enough but I do not know what some of the region(s) are" [-Wcpp]
141 | # warning "CONFIG_MM_REGIONS large enough but I do not know what some of the region(s) are"
| ^~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Adds -fno-strict-aliasing to ARCHOPTIMIZAITON definition for all sim Make.defs file. This is constistent with the setting used in the Make.defs file of all other architectures and should eliminate the build test warnings:
arp/arp_arpin.c: In function 'arp_arpin':
arp/arp_arpin.c:136:13: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
net_ipv4addr_hdrcopy(arp->ah_sipaddr, &dev->d_ipaddr);
^~~~~~~~~~~~~~~~~~~~
arp/arp_format.c: In function 'arp_format':
arp/arp_format.c:96:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
net_ipv4addr_hdrcopy(arp->ah_dipaddr, &ipaddr);
^~~~~~~~~~~~~~~~~~~~
And similar warnings from icmp/icmp_input.c, and tcp/tcp_send.c. -fno-strict-aliasing i required for a warning free build of NuttX code since there is use of punned pointers.
arch/z80/src/ez80/ez80_timerisr.c: Fix an error that looks the file got damaged by a bad keystroke in the editor while a string was highlighted.
boards/z80/ez80/z20x/src/ez80_spi.c: Fix some bad conditional compilationi. Prevented W25 chip select from being initialized.
This reverts commit f735584514.
These header changes introduce unacceptable errors:
1. The changes alter the width of the initial block comment. That will cause nxstyle failures on most of the files.
2. The third line of the header is an (optional) short description of content of the the file. This change erroneously removes that line.
Automated header file changes can screw up a lot of files, very quickly.
Commit 797e45d6bf attempted to reduce the frequency of SPI reconfiguration by keeping track of the current frequency and mode settings and changing these settings only when the new settings differ from the old settings.
However, the original commit neglected to save the new frequency setting and, hence, was not effective in what it was trying to do: Every time the SPI setfrequency() method was called, it still looked like a new frequency and the frequency was still reconfigured, even though it hadn't really changed.
arch/z80/src/ez80/ez80_spi.c: Do not configure SPI chip select pin. It is not used by the driver and configuring it just clobbers other usage of that pin. Add some additional debug outputs; correct some exiting debug outputs.
drivers/mtd/w25.c: Add some debug output.
boards/z80/ez80/z20x/src/ez80_w25.c: Correct SPI bus number used in initialization. Only SPI1 is supported.
arch/z80/src/ez80/ez80_timerisr.c: Some initial timer configuration fixes.
* tools/Config.mk - Add empty definition POSTBUILD
* tools/Makefile.unix/win - Replace CXD56xx specific logic with $(call POSTBUILD)
* boards/arm/cxd56xx/scripts/Config.mk - Add POSTBUILD definitions with logic removed from Makefile.unix/win
* boards/arm/cxd56xx/spresense/scripts/Make.defs - Include the CXD56xx Config.mk immediately after tools/Config.mk so that the empty POSTBUILD definition will be replaced with the correct one
NOTE: There is a precedent for this approach. This is the way that other architecture-specific build options are implemented. See, for example, tools/zds/Config.mk
The SPECIFIC_DRIVERS configuration was removed from the drivers Kconfig and
the build will ignore the specific drivers.
This patch enables the config locally for the CXD56 board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
This sensor driver needs rework to match the needed layout for standar NuttX driver.
In the meantime it is moved to board specific sensors to fix the violation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* SAMA5D27 peripheral support - USB Host working
- updated nsh defconfig with vfat for testing USB Host
- sama5d2_xult: USB Host worked.
- ported sam_bringup.c code from sama5d3-xplained
- USB 2.0 HS now working
- other perpherals may work, but haven't been tested
* update license headers to approve NuttX Apache-2.0
arch/z80/: include/ez80/irq.h, src/ez80/ez80f92_*.asm: Correct some comments related to vector address offsets.
boards/z80/ez80/z20x/scripts/z20x_loader.linkcmd: Fix RAM offset in linker script
* arch: x86_64: Pour-in the x86_64 code from cRTOS repository, excluding modifications of NuttX kernel, jailhouse support and linux compatibility layer
* arch: x86_64: Refactor x86_64 loading procedure for better comprehension and included support for multiboot2
* arch: x86_64: Locate the kernel at 4GB~ and modify the page table initializing procedure accordingly
* arch: x86_64: Implemented kconfig option for various x86_64 capabilities, dynamic probe and check capability on lowsetup before enabling
* arch: x86_64: inte64_check_capability: Use Marco to prettify the capability checking procedure
* arch: x86_64: intel64_timerisr.c: Refactor with new frequency calibrating method
* arch: x86_64: Fix C alias of page table and GDT/IST
* arch: x86_64: Reload GTDR with GDT in high address in up_lowsetup
* arch: x86_64: Consolidate MSR definition in arch/arch.h
* arch: x86_64: Edit the way of handling GDT/IST in C into structures
* arch: x86_64: Correct the starting point of isr/irq stack
* arch: x86_64: Update up_initialize.c with the new initializing procedure
* arch: x86_64: up_map_region now take flags instead of assuming WR/PRESENT
* arch: x86_64: Overhual of interrupt initialization procedure
* arch: x86_64: Properly configure the heap to be memory as [_ebss, end of memory]
* arch: x86_64: Try to probe the TSC frequency, fall-back to user specified frequency on failure
* arch: x86_64: Remove debug printing during restore_aux, causing infinite CTX bug
* arch: x86_64: for X86 16500 serial interrupt to work, OUT2 of MCR must be 1. Make it stuck at 1 after boot
* arch: x86_64: Correctly apply license header, comment and format code
* arch: x86_64: properly send a SIGFPE on floating point error
* arch: x86_64: Remove unused variable in up_restore_auxstate
* arch: x86_64: properly trash the processor with an infinite loop
* arch: x86_64: Fix typo in ISR handler causing ISR not handled
* arch: x86_64: Fix possibile race conditions with scheduler debug option on in signal handling path
* arch: x86_64: Fix typo in MSR_X2APIC_LVTT_TSC_DEADLINE
* arch: x86_64: Migrate tickless implementation to the new MSR naming and frequency calibration method
* board: x86_64: qemu: Add guard to exclude up_netinitialize when compiling without net support
* arch: x86_64: update defconfigs
* arch: x86_64: rename qemu as qemu-intel64
* arch: x86_64: update Board readme
Kconfig files. Repartition some functionality. Bootloader support will need to be provided in logic under arch/z80/src/ez80 so the critical configuration selections were moved the Kconfig file there.
arch/z80/src/ez80/ez80_i2c.h: Rename arch/z80/src/ez80/ez80f91_i2c.h. It is sharable by both ez80f91 and ez80f92.
arch/z80/src/ez80/: Add logic to perform an additional level of interrupt redirection. This is necessary because the the interrupt handling is part of the loader FLASH-based logic. In order to share interrupts with the program loaded into RAM by the loader, another layer or redirection is required to get control to the interrupt handlers in the loaded program. See ez809f2_loader.asm and ez80f92_program.asm
boards/z80/ez80/z20x/scripts: Reduce size of the interrupt re-direction buffer from 1Kb to 512b.
The SD boot loader was not satisfactory because 1) the SD slot is on an optional board and, hence, cannot be part of a fundamental solution. And 2) it is too big.
The only storage on borard is the Winbond W25 SPI-bsed FLASH. This commit adds support for a bootload to 1) read code in HEX format from a serial port and write it to the W25 FLASH, or 2) read code in binary form from the W25 FLASH into SRAM and execute the loaded program.
boards/z80/ez80/z20x/configs: Added w25boot configuration
boards/z80/ez80/z20x/src: Add bootloader logic, w25_main.c. Add logic to manage shared SRAM memory map so that the loaded program does not clobber the bootloader memory. Add logic to recover the bootloader memory into the heap after the loaded program as started.
boards/z80/ez80/z20x/scripts: Rework scripts and configuration to support a bootloader and program build. The boolloader cannot use all of SRAM; the program must not clobber the SRAM region used by the bootloader.
* imxrt: GPIO make tables const
* imxrt: Call out to board to set up FlexRAM
* imxrt: Add Knob for adding the ROM bootloaders 40Kib of RAM to heap
* imxrt: imxrt1060-evk:Add the ability to run from OCRAM
* arch/arm/src/imxrt/imxrt_usbdev.c: Add USB Device support for i.MX RT (USB OTG1)
Based on the LPC43xx USB Device driver.
* imxrt:usbotg Nxstyle fixes
Co-authored-by: thomasactia <61285689+thomasactia@users.noreply.github.com>
board/z80/ez80/*/scripts/Make.defs: Fix optimization definition use in assembly flags. It was using the compiler optimization settings instead of the assembler optimization settings. Hence, enabling optimization would could cause assembler command line errors.
arch/z80/src/ez80/Toolchain.defs: Back out some work arounds. Now compiler optimization flags can again set set without assembler command line errors.
boards/z80/ez80/z20x/README.txt: Trivial update to size/optimization discussion.
The eZ80F92 interrupt controller is very different from the eZ80F91. The eZ80F91 has:
1. Four byte interrupt vectors
2. The vector base address register is 16-bit so the vector table can lie in RAM
Whereas the eZ80F92 has:
1. Two byte interrupt vectors
2. An 8-bit vector base address
This means that the vectors must lie in the first 16-bits of FLASH and there must be a "trampoline" to get to interrupt handlers outside of the first 64-Kb of FLASH.
arch/z80/src/ez80/Toolchain.defs: Correct some CFLAGS when optimization suppressed.
arch/z80/src/ez80/Kconfig arch/z80/src/ez80/ez80_emac.c: Remove configuration option for selecting EMAC RAM address. This is duplicated and possibly conflicting. The correct address for the RAM is provided in the linker command file. The RAM should be configured once and using this single definitions.
arch/z80/src/ez80/ez80_startup.asm and arch/z80/src/ez80/ez80f9*_init.asm. Move RAM and FLAH intialization out of MCU-specific logic to common start-up logic. We cannot call any functions until SRAM is initialized and the stack is properly initialized because the return address is stored on the stack. Use internal SRAM for the IDLE stack to avoid the chicken'n'egg problem.
boards/z80/ez80/z20x/configs/sdboot/sdboot.zdsproj: Discuss build environments.
CONFIG_FAT_MAXFNAME is set to 255 and CONFIG_NAME_MAX is set to 765
which can support max file name including Japanese characters.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
arch/z80/src/ez80/Toolchain.defs: Update some CFLAGS to match CFLAGS from ZDS-II IDE. Apparently, we must say that the CPU is an eZ80F91 event when compiler for eZ80F92.
boards/z80/ez80/z20x: Update linker scripts.
Squashed commit of the following:
commit 685951b5385062035ac558df1112353c9441c910
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 16:33:00 2020 -0800
fixed typo in readme
commit ad1d3289b48af0de3095e3f365429017e57278b3
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 16:07:48 2020 -0800
simulator host route helper script and docs
Squashed commit of the following:
commit cf5cddcf55a155303cb5abb1aa026f6dcaf369ca
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:50:40 2020 -0800
syslog on console to fix compile error
commit def1bb73fcfbc8b115c55d9f4544b97d583807f2
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:46:13 2020 -0800
formatting as per PR feedback; removed ping
commit b179fd8831b77fbbe85527a4ab3161e1f1ca1e43
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 15:45:49 2020 -0800
formatting as per PR feedback
commit e3280bede9798d9a00b118e126c02ceab497e33a
Author: Adam Feuer <adam@starcat.io>
Date: Mon Feb 24 13:56:50 2020 -0800
add simhostroute.sh description to readme
commit 09a6b0ca3bacf005c2a79102141ae8cc3eb91849
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:38:40 2020 -0800
fixed error in simhostroute.sh usage docs
commit d838582119d43ee2002ce3808051c82b23e98c58
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:28:35 2020 -0800
added tcpblaster defconfig and updated docs
commit af3d2d6591f12d1127027fdd363858052094e624
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:21:29 2020 -0800
added info about capabilities and running as root
commit 6359cfdfedefc818b169455401942d3d33a59f41
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:20:42 2020 -0800
updated network linux readme
commit 47feb08aa74e4b1fc6c802567bc777d31e7c9a83
Author: Adam Feuer <adam@starcat.io>
Date: Sun Feb 23 17:09:04 2020 -0800
initial addition
* tools/zds/zds_Config.mk: Move boards/z80/ez80/scripts/eZ80_Config.mk to tools/zds/zds_Config.mk where it can be shared by other ZDS-II platforms.
* boards/z16/z16f: Duplicate changes for new ZDS-II support from ez80
* boards/z80/z8: Duplicate changes for new ZDS-II support from ez80
* arch/z16/src/z16f/Toolchain.defs: Create required Toolchain.defs file for Z16f
Eliminate the MOVEOBJ definition from tools/Config.mk, Makefiles, and other locations. The MOVEOBJ definition was used to work around the case where the object output of a compile or assemble is in a different directory than the source file. The ZDS-II tools have no command line option to perform this move; MOVEOBJ handled the move as a post-compiler operation.
MOVEOBJ is no longer needed because this the ez80 COMPILE and ASSEMBLE definitions now handle all of the object file movement cases.
tools/zds/zdsgen.c: Remove this program. It should have been a simpler way to manage ZDS-II compiler and assember differences. However, the compiler arguments needed to pass through too many layers of bash command line modifications and, as a result, it was not possible to retain quotes on critical strings. This approch was abandoned for an alternative approach.
boards/z80/ez80/scripts/eZ80_Config.mk: Add definitions to move the object files as necessary. This seems to work well and is implemented for both native and Cygwin Windows build -- but only for the Z20x.
tools/zds: A new tool sub-directory intended to hold tools for making life working with the ZDS-II toolchain less painful.
tools/zds/zdsar.c: This is a wrapper around the ZDS_II librarian. It simplifies the build scripts by replacing large sequences of complex Bash script that were added to the build files. Not only does this clean up the build files but it also improves performance and, more importantly, provides a common solution for the Windows native build case. This tool should work with all ZDS-II based platforms including z8, zNeo, and ez80.
tools/README.txt: Add a brief description about the zds sub-directory. Also re-ordered some tool descriptions. They are supposed to be in alphabetical order, but this seems to have fallen apart.
boards/z80/ez80/scripts/eZ80_Config.mk: Updated to use tools/zds/zdsar.exe.
This includes some fixes for the ez80 build including:
1. Ability to handle decorated object file names,
2. Ability to handle libraries described with absolute paths
This commit address only the POSIX build and needs to be updated
for the Windows native build.
arch/z80/arc/ez80/Toolchain.sh: Move more common toolchain definitions from Make.defs.
boards/z80/ez80/scripts/eZ80_Config.mk: Move common defines that override tools/Config.mk to this new file.
This does not solve the ez80 build problem yet but does assure that when the solution is in place, it will automatically apply to all present and future ez80 configurations.
to avoid shell complain that @echo can't find if the variable expand in the compound
command(e.g. ARLOCK) and remove $(Q) before $AR so the result is almost same as before.
Enable optimization and generate debug symbols.
Enable scheduler instrumentation and spinlock irq.
Add applications such as hello, ostest and taskset.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Update linker scripts to provide _ramfuncs sections for SAMv7 based boards. This corrects undefined reference to _ramfuncs when CONFIG_ARCH_RAMFUNCS is enabled (Issue #304)
Largely copy-and-paste from stm32f4discovery.
Also arch/arm/src/armv7-m/mpu.h: Ensure RBAR alignment
Fix crashes on init task startup I observed on qemu-system-arm -M lm3s6965evb.
Because we can get the same function by CONSOLE_SYSLOG/syslog_console_init.
BTW, it isn't a good choice to use g_ramlogfops as /dev/console since nsh
will read back what it send out which will surprise most people.
This commit adds automounter and BOARDCTRL_RESET support for SAMV71 and verified on Atmel SAMV71-XULT. Also, some fixes of Kconfig and missing uerr/uinfo definition.
To ensure size_t same as toolchain definition in the first place and rename CXX_NEWLONG to ARCH_SIZET_LONG. The change also check whether __SIZE_TYPE__ exist before CONFIG_ARCH_SIZET_LONG so our definition can align with toolchain(gcc/clang) definition automatically.
Basically a copy-and-paste from spresense.
But I added -mlong-calls for ELF to avoid out of range relocations.
(Isn't it necessary for spresense?)
gnu-elf.ld is a copy from stm32f4discovery. I changed the license
of this file with a permisson of @patacongo.
Historically, the loopback driver used the largest packet size of all enabled link layer protocols. This permitted packets to be forward via the loopbak device with no major loss of performance. However, in experimenting with configurations where no other link layer protocols were enabled, this means the loopback packet size was set to the smallest possible size, to the SLIP minimum of 296 bytes. This resulted in terrible loopback performance.
This commit adds an option to increase the loopback packet size with the option CONFIG_NET_LOOPBACK_PACKETSIZE.
The loopback driver packet buffer should be quite large. The larger the loopback packet buffer, the better will be TCP performance of the loopback transfers. The Linux loopback device historically used packet buffers of size 16Kb, but that was increased in recent Linux versions to 64Kb. Those sizes may be excessive for resource constrained MCUs, however.
The network still enforces the lower limit that is the maximum packet size of all enabled link layer protocols. But this new option permits the loopback packet size to be increased from that.
* net/Kconfig: Adds CONFIG_NET_LOOPBACK_PKTSIZE option
* include/nuttx/net/netconfig.h: Assures that the packet size that is used is at least as large as the largest packet size of other link layer protocols.
* drivers/net/loopback.c: Use that larger packet size.
* boards/sim/sim/sim/configs/tcploop/defconfig: Set the loopback packet size to 1500
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
* include: Introduce elf64.h and elf.h
Added elf64.h for 64bit ELF support and moved common definitions
from elf32.h to elf.h. Also introduced Elf_xxx to be used in
common libraries such as binfmt.
* binfmt, include, modlib, module: Add support for ELF64
Elf_xxx must be used instead of Elf32_xxx to support ELF64.
To use ELF64, CONFIG_ELF_64BIT must be enabled.
* binfmt, modlib: Add support for relocate address
* arch: risc-v: Add include/elf.h
* libs: machine: Add risc-v related files.
NOTE: Currently only supports ELF64
* boards: maix-bit: Add elf and posix_spawn configurations
* boards: maix-bit: Add support for module configuration
* S32K add support for Nxp drone boards
* Update arch/arm/src/s32k1xx/hardware/s32k1xx_rtc.h codestyle
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
It seems that "ld -r" on macOS doesn't include objects from
libraries for common symbols. Because of that, sim build
ends up with undefined references to globals like g_binfmts
and g_mmheap.
Namely this changes HOSTOS for macOS from "Other" to "Darwin".
Also, suppress the following harmless messages during a "make":
(Missing redirect in tools/Makefile.host)
uname: illegal option -- o
usage: uname [-amnprsv]
Add CONFIG_MMCSD_SDIO=y to configuration. This eliminates the following error found in build testing: lpc17_40_bringup.c: undefined reference to mmcsd_initialize
This change backs out a portion of ac4735cf58 and corrects the dependencies on CONFIG_NETUTILS_TELNETD. Without this change, the configuration will not build. It will fail with:
nsh.h:154:4: error: #error "No NSH frtont end defined."
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix warning: selects SDIO_DMA or SDIO_BLOCKSETUP which has unmet direct dependencies (MMCSD)
Fix warning: selects NETDEV_TELNET which has unmet direct dependencies (NETDEVICES && NET && NET_TCP)
Fix warning: selects ARCH_PHY_INTERRUPT which has unmet direct dependencies (NETDEVICES && ARCH_HAVE_PHY)
Fix warning: selects USBHOST_HAVE_ASYNCH which has unmet direct dependencies (USBHOST)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
to fix the follow error:
Refresh z16f2800100zcog/nsh
LN: include/arch to arch/z16/include
LN: include/arch/board to /workspace/mirtos/nuttx/boards/z16/z16/z16f2800100zcog/include
No directory at /workspace/mirtos/nuttx/boards/z16/z16/z16f2800100zcog/include
to fix the follow error:
Refresh us7032evb1:nsh
LN: include/arch to arch/renesas/include
LN: include/arch/board to /workspace/mirtos/nuttx/boards/renesas//us7032evb1/include
No directory at /workspace/mirtos/nuttx/boards/renesas//us7032evb1/include
to fix the follow error:
Refresh skp16c26/ostest
LN: include/arch/board to /workspace/mirtos/nuttx/boards/renesas/m32262f8/skp16c26/include
LN: include/arch/chip to arch/renesas/include/m32262f8
fix the follow error:
Refresh demo9s12ne64/ostest
LN: include/arch/board to /workspace/mirtos/nuttx/boards/hc/mcs92s12ne64/demo9s12ne64/include
LN: include/arch/chip to arch/hc/include/mcs92s12ne64
No directory at /workspace/mirtos/nuttx/arch/hc/include/mcs92s12ne64
Author: liuhaitao <liuhaitao@xiaomi.com>
clicker2-stm32/mrf24j40-mac: enable SCHED_LPWORK config to fix build break
ieee802154/mac802154_internal.h:75:4: error: #error Both Low and High priority work queues are required for this driver
75 | # error Both Low and High priority work queues are required for this driver
| ^~~~~
ERROR: arm-none-eabi-gcc failed: 1
nucleo-f303re/nxlines: enable NXSTART_EXTERNINIT config to fix build break
arm-none-eabi-ld: /var/lib/jenkins/workspace/NuttX-Nightly-Build/nuttx/staging/libgraphics.a(nxmu_start.o): in function `nx_server':
nxmu_start.c:(.text+0x2): undefined reference to `board_lcd_initialize'
arm-none-eabi-ld: nxmu_start.c:(.text+0xc): undefined reference to `board_lcd_getdev'
make[1]: *** [nuttx] Error 1
Disable cxx new long to fix build break for some sam34 boards configs
Build fail log as below:
CXX: libxx_new.cxx
libxx_new.cxx:66:7: error: 'operator new' takes type 'size_t' ('unsigned int') as first parameter [-fpermissive]
66 | void *operator new(unsigned long nbytes)
| ^~~~~~~~
Makefile:102: recipe for target 'libxx_new.o' failed
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
sama5d3-xplained:ethernet-over-phy configuration found in build testing:
arch/arm/src/sama5/sam_irq.c: Fix "Control reaches end of non-void function " warning
arch/arm/src/sama5/sam_udphs.c: Fix "unused variable 'epno'" warning
boards/arm/sama5/sama5d*-*/src/sam_usb.c: Fix "warning 'HAVE_USBHOST' not defined" warnings
Kconfig: the CONFIG_WINDOWS_NATIVE options now depends on CONFIG_EXPERIMENTAL. The Windows native build is complete and available, but not often used or verified. As a consequence, it cannot be assured to be fully functional at any given time. Hence, it is marked here as EXPERIMENTAL so that the end user will be aware of this state.
boards/arm/stm32/stm32f4discovery/configs/winbuild/defconfig: Add CONFIG_EXPERIMENTAL to the windbuild configuration. It is now necessary for this configuratino to be a viable test configuration.
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Add pinguino-debug.ld for PIC32MX boards to fix build break under
PINGUINO gcc toolchain. All pinguino-debug.ld copy from the original
mips debug/release ld scripts.
Change-Id: Ie47a2523470cc9996d007bc4afbf9cb40e51ae5b
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
* arch/arm/src/nrf52/hardware/nrf52_twi.h: fix typo
* arch/arm/src/nrf52/nrf52_i2c.c: add interrupts support and some debug messages
* boards/arm/nrf52/nrf52840-dk: add support for hts221 and lsm303agr; boards/arm/nrf52/nrf52840-dk: fix issues noted by nxstyle
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle again .c file and fix error message
Author: Daniel P. Carvalho <danieloak@gmail.com>
Add SPWM example to test STM32L4 PWM driver low level operations.
Fix BUGs.
1. No .c file should include a "Public Types" section. Only a header file can define a public type. A .c file can only define a private type. Several files contained private type definitions. The section that they were defined in, however, was incorrectly named "Public Types." Those were easilty changed to "Private Types" which is what they are.
2. No .c file should include a "Public Function Prototypes" section. All global function prototypes should be provided via a header file and never declared with a .c file.
For No. 2, I corrected as many cases as was reasonable for the time that I had available. But there are still a dozen or so .c files that declare "Public Function Prototypes" within a .c file. This is bad programming style. These declarations should all be moved to the proper header files.
Here is the email loop talk about why it is better to remove the option:
https://groups.google.com/forum/#!topic/nuttx/AaNkS7oU6R0
Change-Id: Ib66c037752149ad4b2787ef447f966c77aa12aad
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* arch: risc-v: Remove unused typedef for irqstate_t
NOTE: irqstate_t is defined in arch/risc-v/include/types.h
* arch: risc-v: Add typedef irqstate_t for __LP64__
* arch: risc-v: Add SMP support to K210 (RV64GC) processor
* boards: maxi-bit: Update READMEs and add smp/defconfig
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c .h files and fix it
Author: Adam Feuer <adam@starcat.io>
Summary
Adds CDC ECM Ethernet over USB High Speed for SAMA5D36-Xplained
(and maybe other boards) (most of the code was there already,
but didn't work out of the box for the SAMA5D36-Xplained)
Only SAMA5D36-Xplained has been tested so far
Impact
None if you don't use the CDC ECM Ethernet driver
On SAMA5D36-Xplained, this adds high-speed Internet connectivity
over USB 2.0 High Speed. via the USB CDC ECM Gadget driver.
It may work on other boards too.
This also fixed full-speed (low-speed) mode for the board too.
Limitations
Hasn't been tested on anything other than SAMA5D36-Xplained board.
TODO
Ideally this would include a composite RNDIS device so it would
also work seamlessly on Windows. That is for a future PR
Ideally this would include software to help configuration via
mDNS/DNS-SD for plug and play compatibility with Linux and macOS.
That is for a future PR.
Detail
Only a few lines of C driver code needed to be changed, since the
capability was there already. The rest is config and documentation.
Changes the SAMA5D3-Xplained board bringup to match the SAMA5D3-EK
board bringup
A helper script to configure Linux routing and iptables NAT is also
provided, along with documentation on how to use it.
Testing
Manual, on a Ubuntu Linux 19.10 system and MacOS 10.14.6 Mojave
MacBook Pro.
How To Verify
Follow the new CDC ECM Ethernet over USB instructions in the board
README.txt file
Commits:
remove non-UTF-8 chars in comment and reformat
removed unneeded comment markers
instructions for using the defconfigs
removed EMAC from config
- to prove this example only needs the CDC ECM Ethernet over USB to work
added CDC-ECM Ethernet over USB info to README
added U-Boot image
added netusb helper script
- this can configure the Linux network interface and routes
so you can ping or access the NuttX system via TCP/IP.
renamed defconfig dirs to be ethernet-over-usb
- was usb-over-ethernet which is not right
added USB DMA to defconfigs
updated readme with autoboot and debugging info
bringing ethernet-over-usb examples into parity
added cdc ecm ethernet over usb with telnetd config
added defconfig
only use phy interrupt if netdevices is ethernet
- because now netdevice could be CDC ECM ethernet over usb
which has no PHY interrupt
add bringup to Makefile
add bringup
app init cleanup
init cdc ecm driver and rndis driver; some cleanup
fixed some typos and odd characters
usb over ethernet working over usb 2.0 hs
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle to check .c and .h files and fix reported issues
Author: liuzhao <happypapa@yeah.net>
Add Quectel EC20 4G LTE Module USB CDC/ACM support
This function fails to compile due to numerous undeclared register definitions used in cxd56_audio_bca_reg.c. This commit replaces the undefined definitions with very similar definitions recommended by GCC (differing only in some spelling).
However, I cannot be certain that this is correct. This must be reviewed, corrected, and verified by Alin Jerpelea. Please do not merge until Alin approves.
The configuration that demonstrates the failure is spresense:audio.
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix small typos and check against nxstyle
Author: Gregory Nutt <gnutt@nuttx.org>
boards/arm/lpc43xx/bambino-200e/src/lpc43_appinit.c: Eliminate a warning found in build testing.
The removal of (void) from all functions whose return value has been ignored has introduced several new warnings into the build test output. For example in lpc3_appinit(), I now see this:
# define nsh_spifi_initialize() (OK)
and
nsh_spifi_initialize();
which generaterd a new warning: "warning: statement with no effect [-Wunused-value]". This commit fixes that warning.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
