imxrt:Clock config fixes and board.h sets sources and divisors
* imxrt:clockconfig bug fix & Board config set clocks
Fixed logic that was not clearing bits as ~ was
mising in &= mask operations.
Use valuse from the board.h file so set the Mux that
selects the clock sources.
Use board defined PODF values to select clock.
Only configure USDHC2 clocks when board defines clocks.
* imxrt1050-evk:Board setting used to set LSPI and USDHC Clocks
Approved-by: GregoryN <gnutt@nuttx.org>
Master imxrt
* imxrt:Fix typos bit# and names
* imxrt:wdog Registers are 16 Bits
* imxrt:wdog Update has to be within 255 clocks of unlock
* imxrt:clockconfig Fix comments
* imxrt1050-evk:board.h Fix comments
* imxrt:imxrt_ccm.h Define Mux Selects for board.h use
* imxrt:clockconfig Allow better control from board.h
1) Allows a board config clock setting to be defined
in terms of the /n values shown in Figure 18-2.
Clock Tree of the i.MX RT1050 Processor Reference
Manual, Rev. 1, 03/2018
2) Allows the clock multipelx selection to be made in
The board config.
* imxrt1050-evk:Define board clocking based on divisor and muxes
Approved-by: GregoryN <gnutt@nuttx.org>
(1) Now the Ethernet is completely re-initialized when an error occurs by means of taking the interface down and back up but the PHY is _not_ renegotiated for that case because that is very time consuming and an error in the Ethernet is no reflection on the state of the PHY anyway.
(2) Explicitly sets the expected PHY address to zero (this could be moved into the config) rather than searching for it which takes ages, and it's zero anyway for this board (that's the broadcast address, and anything that cannot respond on that has multiple PHYs, so that would be a new board).
(3) Allows for the renegotiation of the PHY to be optional when a reset is needed. If a non-renegotiated reset doesn't result in good comms to the PHY then it'll automatically be escalated to a renegotiated one.
(4) Only performs a reset for errors that need it (the CRITICAL_ERROR define). The list of errors that need reset are somewhat arbitrarily chosen based on my prejudices and might need to be revisited, but certainly the jabber errors don't need reset, the partial packet is thrown away by the layer above anyway.
(5) Re-loads the multicast table on reset.
(6) Adds a bit more logging into the imxrt Ethernet module.
- Added CRC32 functions for multicast address filtering.
- Do not reset PHY settings when doing an ifup
- Use chip's unique id as the device MAC
- Enable discard enet frames with errors at PHY layer
This makes the user interface a little hostile. People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header). A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length. Instead, we define the packet buffer size then derive the MTU.
The MTU is not common currency in networking. On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP). Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes. So we should be all good and without the recurring 14 byte error in MTU's and MSS's.
Squashed commit of the following:
Trivial update to fix some spacing issues.
net/: Rename several macros containing _MTU to _PKTSIZE.
net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU. These are not the MTU which does not include the size of the link layer header. These are the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE. This is not the MTU which does not include the size of the link layer header. This is the full size of the packet buffer memory (minus any GUARD bytes).
net/: Rename the file d_mtu in the network driver structure to d_pktsize. That value saved there is not the MTU. The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header. The MTU does not include the link layer header.
Squashed commit of the following:
arch/arm/src/imxrt: Fix some first time compile issues.
arch/arm/src/imxrt: This brings the RTC implement to code complete but still untested.
arch/arm/src/imxrt: Add some RTC initialization logic.
arch/arm/src/imxrt: Flesh out most of the RTC driver lower half and LPSRTC support.
arch/arm/src/imxrt: Some inital, partial implementation of the HPRTC and LPSRTC.
arch/arm/src/imxrt: Add HPSRTC/HPRTC file framework (no logic, just skeleton files).
arch/arm/src/imxrt: Add HPRTC header file.
Some initial configuration logic for SNVS LPRTC and HP RTC.
arch/arm: Remove support for CONFIG_ARMV7M_CMNVECTOR. It is now the only vector support available. Also remove CONFIG_HAVE_CMNVECTOR. That no longer signifies anything."
arch/arm/src/stm32: This commit removes support for the dedicated vector handling from the STM32 architecture support. Only common vectors are now supported.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/imxrt: Add cache operations to permit the Ethernet driver to work with the D-Cache enabled, at least in write-through mode.
Author: Jake Choy <jakearcx@gmail.com>
arch/arm/src/imxrt: The Ethernet driver is now functional, at least with the D-Cache off. The final fix was for the reference clock that needs to be forced to provide and input (SION).
Author: Gregory Nutt <gnutt@nuttx.org>
Fix trivial coding standard issue.
configs/imxrt1050-evk: Correct CONFIG_RAM_SIZE in all configurations (5Kb not 5Mb). I don't believe that CONFIG_RAM_SIZE is used at all in the i.MX RT so this is as grievous an error as it seems. Also enabled built-in applications in all NSH configurations.
arch/arm/src/imxrt/imxrt_enet.c: Trivial and cosmetic.
Cosmetic update to comments.
arch/arm/src/imxrt/imxrt_enet.c: Oops.. put the PHY interrupt init hooks in the wrong place. That is a one-time initialization but imxrt_initphy() is called on each ifup.
arch/arm/src/imxrt/imxrt_enet.c: Add hooks for board-specific PHY initialization (not yet needed, but there when needed).
Remove dangling white space at the end of lines
arch/arm/src/imxrt/Kconfig: Add option for board-specific PHY initialization.
configs/imxrt1050-evk/src: Add basic logic to support PHY interrupts. Incomplete.. needs additional support in imxrt_enet.c to 1. call to initialize PHY interrupt features, and 2. IOCTL commands to access PHY registers.
configs/imxrt1050-evk/README.txt: Trivial update.
configs/imxrt1050-evk/netnsh/defconfig: Disable LED support because pins conflict with PHY. Enable device statists. Enable NSH ifup and ifdown commmands
arch/arm/src/imxrt: Use macros in imxrt_periphclks.h vs. direct CCM CCGR accesses in Ethernet driver.
arch/arm/src/imxrt: Misc changes for a clean compilation of Ethernet deriver. configs/imxrt1050-evk/netnsh: Add an NSH configuration for testing Ethernet.
Author: Jake Choy <jakearcx@gmail.com>
arch/arm/src/imxrt: Initial WIP Ethernet driver.
arch/arm/src/imxrt: May eDMA channel linking a configuration option. Add support to select the DMA channel priority and pre-emption controls.
arch/arm/src/imxrt: Update some HowTo comments in the eDMA header file.
arch/arm/src/imxrt: Fix a logic error in parmater passing. Caller does not know actual channel number when setting up linked channel, only the channel handler.
arch/arm/src/imxrt: Fixes for clean eDMA driver build with Scatter/Gather enabled.
arch/arm/src/imxrt: Fixes for clean eDMA driver build with Scatter/Gather disabled.
arch/arm/src/imxrt: Add flags to DMA configuration to control transfer setup. Remove some user interfaces that are inconsistent with modular design.
arch/arm/src/imxrt: Update DMA channel interrupt handler.
arch/arm/src/imxrt: Add implementation of eDMA imxrt_dmach_start().
arch/arm/src/imxrt: Add implementation of eDMA imxrt_dmach_setup().
arch/arm/src/imxrt: Add eDMA imxrt_tcd_chanlink().
arch/arm/src/imxrt: Add eDMA imxrt_dmach_getcount; free allocated TCDs automatically when the DMA completes or is aborted.
arch/arm/src/imxrt: Add structures to support list of TCDs for Scatter/Gather DMA.
arch/arm/src/imxrt: Add eDMA imxrt_dmach_initconfig().
arch/arm/src/imxrt: Add eDMA imxrt_tcd_instantiate().
arch/arm/src/imxrt: Replacing some of the logic cloned from SAMv7 XDMAC with eDMA logic from NXP sample code. I am thinking that the eDMA is too complex to force into the same pattern as for other MCUs.
arch/arms/src/imxrt/imxrt_edma.c: Add support for in-memory TCDs.
arch/arm/src/imxrt/chip: Add an in-memory representation of the TCD in imxrt_edma.h
imxrt_gpioirq.c
- Add check for interrupt mask register before dispatching ISR. The GPIO_ISR bits are set independent of the GPIO_IMR bits.
imxrt_irq.c
- fixed a range check for extint in function imxrt_irqinfo().
This port was the joing effort of Janne Rosberg, Ivan Ucherdzhiev, and myself. I give credit to Ivan for the kill because he is the one to held on to the end.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
configs/imxrt1050-evk/scripts: Add section to linker script to handle the case where RAMFUNCs are enabled. RAMFUNCs appear to be enabled in the default configuration ... they probably should not be enabled.
Author: Ivan Ucherdzhiev <ivanucherdjiev@gmail.com>
arch/arm/src/imxrt: imxrt_lowputc.c is finished. Now everything needed for the initial port is done and ready for testing.
arch/arm/src/imxrt: Add logic to imxrt_lowputc.c. Still incomplete.
Author: Ivan Ucherdzhiev <ivanucherdjiev@gmail.com>
arch/arm/src/imxrt: Add serial support. configs/imxrt1050-evk: Add linker script.
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/imxrt: Add initial cut at imxrt_allocateheap.c
Author: Ivan Ucherdzhiev <ivanucherdjiev@gmail.com>
arm/arm/src/imxrt: Completes all definitions for PADMUX, CTLMUX, and IOMUX_INPUT and mapping tables on imxrt_gpio.c and imxr_iomuxc.c.
arch/arm/src/imxrt/chip: Add definitions for IMXRT_PADCTL and IMXRT_PADMUX registers. Only the IMXRT_INPUT definitions in this commit.
arch/arm/src/imxrt/chip: Add more IOMUXC register definitions.
Author: Gregory Nutt <gnutt@nuttx.org>
configs/imxrt1050-evk: Add STRIP definition to Make.defs.
arch/arm/src/imxrt: Bring in i.MX6 memory configuration settings.
arch/arm/src/imxrt: Remove call to non-existent imxrt_gpioinit() from imxrt_start.c.
arch/arm/src/imxrt: Bring in incomplete imxrt_iomuxc.c file from i.mx6.
arch/arm/src/imxrt: Add first cut at GPIO interrupt logic.
arch/arm/include: Add definitions to support a second level of GPIO pin interrupts.
Author: Janne Rosberg <janne.rosberg@offcode.fi>
arch/arm/src/imxrt: Add imxrt_wdog.c/.h
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/imxrt: Port SAMv7 interrupt logic to imxrt_irq.c.
arch/arm/src/imxrt: More clarification of the start-up memory map.
arch/arm/src/imxrt: Some mostly cosmetic clean-up to the imxrt_start.c file that was so rudely taken from the SAMv7.
arch/arm/src/imxrt: Add imxrt_start.c. Initial commit is the the SAMv7 startup logic with name changes.
Author: Ivan Ucherdzhiev <ivanucherdjiev@gmail.com>
arch/arm/src/imxrt: Adds a few IOMUXC register definitions.
Author: Janne Rosberg <janne.rosberg@offcode.fi>
arch/arm/src/imxrt: Add imxrt_clockconfig.c/.h
configs/imxrt1050-evk: Add clock configuration definitions to board.h
arch/arm/src/imxrt: Fix CCM register name; Fix doubly defined in LPUART bit field.
arch/arm/src/imxrt: Add analog defines to CCM register definition header file.
Author: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/imxrt: Bring in GPIO C files from i.MX6. Things are in disarray now because that GPIO logic depends on IOMUXC logic which is not yet in place.
arch/arm/src/imxrt: Add a few more GPIO definitions to make the header file compatible with i.MX6
arch/arm/src/imxrt/chip: Add GPIO register definition file.
Author: Janne Rosberg <janne.rosberg@offcode.fi>
arch/arm/src/imxrt: Add DCDC register definitions.
arch/arm/srch/imxrt: Add CCM register bit definitions
Author: Gregory Nutt <gnutt@nuttx.org>
Purely cosmetic
arch/arm/src/imxrt: Add system reset controller register definition header file.
Embarassingly trivial change left in compiler.
arch/arm/src/imxrt: Finishes i.MX RT1050 LPUART register definition header file.
arch/arm/src/imxrt: Beginning of an i.MX RT1050 LPUART register definition header file.
Some trivial things
Author: Janne Rosberg <janne.rosberg@offcode.fi>
arch/arm/src/imxrt: Add imxrt_wdog.h
arch/arm/src/imxrt: Add initial imxrt_ccm.h
Author: Gregory Nutt <gnutt@nuttx.org>
Trivial update to README.
arch/arm/src/imxrt: The i.MX Rt implements 4 bits of interrupt priority, not two. Thanks, Janne.
arch/arm/src/imxrt: Fix some initial compile issues. Still a long way from complete, but there is a buildable environment now for the imxrt1050-evk.
configs/imxrt1050-evk: Add an initial NSH configuration for testing.
configs/Kconfig: Hook the i.MX RT 1050 board configuration into the NuttX configuration system.
configs/imxrt_evk: Add the framework for i.MX RT 1050 board support.
arch/arm/src/imxrt: Bring in a few more files from LPC54xxx.
arch/arm/src/imxrt: Bring in imxrt_clrpend() from the LPC54xxx.
arch/arm/src/imxrt: Bring in Cortex-M7 SysTick setup from the SAMv7.
arch/arm/src/imxrt: Add a few easy files.
arch/arm/src/imxrt/chip: Add memory map header files.
arch/arm/src/imxrt: A few basic files to start the port to the i.MX RT 1050.
