utilize the call inside nxtask_exit instead, also move
nxsched_suspend_scheduler to nxtask_exit for symmetry
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I219fc15faf0026e452b0db3906aa40b40ac677f3
This fixes the following 3 issues:
1. Wait for send to complete in exchange
Before shutting down the SPI, we have to wait for send to complete; not only
DMA, since DMA just puts data to the SPI fifo. It is not yet out of SPI.
When doing exchange with both send & receive this is not an issue because when
receive dma has completed, it is certain that also the send is.
This can be accomplished by completing the transfer in SPI TXC interrupt
instead of DMA callback.
2. Fix TXDMAEN and RXDMAEN placement
According to the spec, the RXDMAEN must be enabled before
enabling DMA requests for Tx and Rx in DMA registers, and TXDMAEN
after that.
Cleaner place to do this is in spi_dmarxstart and spi_dmatxstart, where
also the dma requests are enabled. This also handles properly the
simplex modes.
3. Remove bus signal glitches when shutting off SPI block
Use AFCNTR to avoid glitches in SPI lines while turning SPI block
on/off during calls to exchange.
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
574b25 broke the internal DMA buffers usage that solved
the following problem: The DMA capable interface does
not know the buffers extent. It calulates it from size.
The user may need to transfer less than a cachline bytes,
but STILL have a DMA cabable buffer. The user is therefore
foreced to transfer more data then needed to "trick" the
DMA cabable function. This is a wast of bus bandwith and
may not work will all devices. The internal buffer, solve
this issue.
stm32h7:stm32_spi review changes
Added sugestion from jlaitine to support RX only.
This is a work in progress, and now only serves as
DMA enabled simplex RX-only mode bus controller
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
-Move task_init() and task_activate() prototypes from include/sched.h to include/nuttx/sched.h. These are internal OS functions and should not be exposed to the user.
-Remove references to task_init() and task_activate() from the User Manual.
-Rename task_init() to nxtask_init() since since it is an OS internal function
-Rename task_activate() to nxtask_activate since it is an OS internal function
Add support for the STM32G474 family of microcontrollers and the
B-G474E-DPOW1 Discovery Board, which features a STM32G474RET6.
This is a major pull request as it adds support for an entirely
new family of STM32. This support is implemented in
arch/arm/src/stm32 and shares implementation with other STM32
families supported by that code, such as the 'L15xx, 'F10xx,
'F20xx, 'F3xxx, and 'F4xxx.
arch/arm/Kconfig:
arch/arm/include/stm32/chip.h:
arch/arm/include/stm32/irq.h:
arch/arm/src/stm32/Kconfig:
arch/arm/src/stm32/hardware/stm32_adc.h:
arch/arm/src/stm32/hardware/stm32_adc_v2.h:
arch/arm/src/stm32/hardware/stm32_dma.h:
arch/arm/src/stm32/hardware/stm32_dma_v1.h:
arch/arm/src/stm32/hardware/stm32_flash.h:
arch/arm/src/stm32/hardware/stm32_i2c.h:
arch/arm/src/stm32/hardware/stm32_i2c_v2.h:
arch/arm/src/stm32/hardware/stm32_memorymap.h:
arch/arm/src/stm32/hardware/stm32_pinmap.h:
arch/arm/src/stm32/hardware/stm32_tim.h:
arch/arm/src/stm32/stm32_allocateheap.c:
arch/arm/src/stm32/stm32_dma.c:
arch/arm/src/stm32/stm32_dma_v1.c:
arch/arm/src/stm32/stm32_dumpgpio.c:
arch/arm/src/stm32/stm32_gpio.c:
arch/arm/src/stm32/stm32_gpio.h:
arch/arm/src/stm32/stm32_lowputc.c:
arch/arm/src/stm32/stm32_rcc.c:
arch/arm/src/stm32/stm32_rcc.h:
arch/arm/src/stm32/stm32_serial.c:
arch/arm/src/stm32/stm32_syscfg.h:
arch/arm/src/stm32/stm32_uart.h:
* Add architectural support to existing NuttX files. This
makes the STM32G474 family parts accessible to the system.
With big thanks for detailed code review:
David Sidrane (davids5)
Mateusz Szafoni (raiden00)
Abdelatif Guettouche (Ouss4)
Add support for the STM32G474 family of microcontrollers and the
B-G474E-DPOW1 Discovery Board, which features a STM32G474RET6.
This is a major pull request as it adds support for an entirely
new family of STM32. This support is implemented in
arch/arm/src/stm32 and shares implementation with other STM32
families supported by that code, such as the 'L15xx, 'F10xx,
'F20xx, 'F3xxx, and 'F4xxx.
arch/arm/include/stm32/stm32g47xxx_irq.h:
arch/arm/src/stm32/hardware/stm32g474cxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474mxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474qxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474rxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g474vxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_gpio.h:
arch/arm/src/stm32/hardware/stm32g47xxx_memorymap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_pinmap.h:
arch/arm/src/stm32/hardware/stm32g47xxx_pwr.h:
arch/arm/src/stm32/hardware/stm32g47xxx_rcc.h:
arch/arm/src/stm32/hardware/stm32g47xxx_syscfg.h:
arch/arm/src/stm32/hardware/stm32g47xxx_uart.h:
arch/arm/src/stm32/stm32g47xxx_rcc.c:
* New files required for architectural support. Note that
existing NuttX files are not modified. As such, in this
revision, the system is unaffected by their addition.
With big thanks for detailed code review:
David Sidrane (davids5)
Mateusz Szafoni (raiden00)
Abdelatif Guettouche (Ouss4)
remove the TLS alignment check
Regression by:
--------------------------------------------------------
commit a6da3c2cb6
Author: Ouss4 <abdelatif.guettouche@gmail.com>
Date: Thu May 7 18:50:07 2020 +0100
arch/*/*_checkstack.c: Get aligned address only when
CONFIG_TLS_ALIGNED is enabled.
--------------------------------------------------------
commit c2244a2382
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Thu May 7 09:46:47 2020 -0600
Remove CONFIG_TLS
A first step in implementing the user-space error is
force TLS to be enabled at all times. It is no longer optional
Signed-off-by: chao.an <anchao@xiaomi.com>
For SDMMC1, IDMA cannot access SRAM123 or SRAM4. Refer to ST AN5200 for
details. This patch makes stm32_dmapreflight check the buffer address and
return an error when the buffer is located in a invalid address space.
This does not fix the hardware limitation but at least makes it visible.
This simplifies the sdmmc driver when the IDMA is in use. There is no need to mix
IDMA and interrupt based transfers; instead, when making unaligned data tranfers,
just make IDMA into an internal aligned buffer and then copy the data.
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
It should not be an error to clean cache beyond the dma source buffer
boundaries. It would just prematurely push some unrelated data from
cache to memory.
The only case where it would corrupt memory is that there is a dma
destination buffer overlapping the same cache line with the source
buffer. But this can't happen, because a destination buffer must always
be cache-line aligned when using write-back cache.
This patch enables doing dma tx-only transfer from unaligned source
buffer when using write-back cache.
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
Correct flash write and erase functions, they inherit some
broken code from other platforms. Also fix the confusion between
eraseblock(sector) and page sizes.
Signed-off-by: Jari Nippula <jari.nippula@intel.com>
If the flash option register was locked before modifying it, return
it to the locked state after modify.
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
Remove support for the Codesourcery, Atollic, DevKitArm, Raisonance, and CodeRed toolchains. Not only are these tools old and no longer used but they are all equivalent to standard ARM EABI toolchains. Retaining specific support has no effect (they are still supported, but now just as generic EABI toolchains).
First, configure the dmacfg in spi_dmarxsetup and spi_dmatxsetup. Then,
check for dmacapable, and only after that set up the dma.
This way the dmacapable actually works, and we don't need to initialize
the dmacfg structures twice.
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
When starting dma transfer, the dcache for the TX buffer should be cleaned.
"flush" performs also invalidate, which is unnecessary. The TX buffer
can be unaligned to the cahche line in some(most) cases, whereas RX buffer
can never be.
The cache for the receive buffer can be dirty and valid before call to exchange.
Thus another memory access (hitting the same cache line) may corrupt receive data
while waiting for transfer to complete. So the receive buffer should be
invalidated before the transfer
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
Modify some comments and debug assertions, which inherit from previous versions
and make no sense. Also add a few nerr printouts to make it easier to debug
running out of buffers
Signed-off-by: Jukka Laitinen <jukka.laitinen@intel.com>
See the following commit in SDK:
commit 62a2fb4fd3001aefad9ec3b2e2e7c47e5b0f21e1
Author: SPRESENSE <41312067+SPRESENSE@users.noreply.github.com>
Date: Fri Jan 24 13:32:04 2020 +0900
Enable dummy transfer by SPI using DMA
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
All complaints fixed except for those that were not possible to fix:
- Used of Mixed case identifier in ESP32 files. These are references to Expressif ROM functions which are outside of the scope of NuttX.
- Remove per-thread errno from the TCB structure (pterrno)
- Remove get_errno() and set_errno() as functions. The macros are still available as stubs and will be needed in the future if we need to access the errno from a different address environment (KERNEL mode).
- Add errno value to the tls_info_s structure definitions
- Move sched/errno to libs/libc/errno. Replace old TCB access to the errno with TLS access to the errno.
Move the logic to get TLS information from an inline function to a normal function. For the unaligned case, it is probably too large to be inlined.
Also fixes some minor things from review of previous commits.
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all architecture-private functions begin with the name of the arch, not up_.
This PR addresses only these name changes for the ARM-private functions up_instack_base() and up_instack_top() which should be called arm_instack_base() and arm_instack_top().
There should be no impact of this change (other that one step toward more consistent naming).
Normal PR checks are sufficient
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the MCU, not up_.
This PR addresses only these name changes for the STM32-private functions up_waste() which should be called stm32_waste.
There should be no impact of this change (other that one step toward more consistent naming).
Normal PR checks are sufficient
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the architecture, not up_.
This PR addresses function-like macro naming that was missing in previous PRs: up_savestate() and up_restorestate() which must be named arm_savestate() and arm_restorestate().
Impact
There should be no impact of this change (other that one step toward more consistent naming).
Testing
stm32f103-minimum:nsh
The are remaining nxstyle complaints due to the use of mixed case identifiers in arch/arm/src/lc823450/lc823450_irq.c This, cannot be easily fixed since it depends on register definitions in header files that have implications to section other lc823450 files.
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the architecture, not up_.
This PR addresses only these name changes for the ARM-private functions up_ramvec_initialize() and up_ramvec_attch().
Impact
There should be no impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private functions begin with the name of the architecture, not up_.
This PR addresses only these name changes for the ARM-private functions prototyped in arm_internal.h
This change to the files only modifies the name of called functions. nxstyle fixes were made for all core architecture files. However, there are well over 5000 additional complaints from MCU drivers and board logic that are unrelated to to this change but were affected by the name change. It is not humanly possible to fix all of these. I ask that this change be treated like other cosmetic changes that we have done which do not require full nxstyle compliance.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.S files.
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Summary
The naming standard at https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ requires that all MCU-private files begin with the name of the architecture, not up_.
This PR addresses only these name changes for the up_*.h files. There are only three, but almost 1680 files that include them:
up_arch.h
up_internal.h
up_vfork.h
The only change to the files is from including up_arch.h to arm_arch.h (for example).
The entire job required to be compatible with that Naming Convention will also require changing the naming of the up_() functions that are used only within arch/arm and board/arm.
Impact
There should be not impact of this change (other that one step toward more consistent naming).
Testing
stm32f4discovery:netnsh
Since armv8-m now uses arm_fullcontextrestore instead of up_fullcontextrestore, _exit
should call arm_fullcontextrestore for armv8-m accordingly.
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
This files in the arch/arm/src/armv8-m directory were cloned from arch/arm/src/armv7-m. Naming standards were created for the architecture files, function, and variable names: https://cwiki.apache.org/confluence/display/NUTTX/Naming+FAQ
There however were never appliced to arch/arm/src/armv7-m and so this bad naming was inherited by arch/arm/src/armv8-m. This commit corrects the file naming only and makes it compliant with the Naming FAQ.
In a fit of confusion, I accidentally committed PR 879 before it passed its nxstyle check (it did pass all of its build tests, but not the style check). It was really my intention to merge PR878, but I screwed that up and merged 879 instead.
This PR makes amends by passing all of the .c and .h files modified by PR879 through nxstyle and correcting all reported style problems.
Mac OS X was renamed to macOS at some point. Update references to
OSX, OS X, Mac OS X, Mac OSX, and other permutations, to macOS,
in README files and in comments of other files.
1. Add dsp extension; float point based on hardware and software.
2. Delete folder "iar"
3. Add tool chain for cortex-M23 and cortex-M35p
Signed-off-by: qiaowei <qiaowei@xiaomi.com>
Change-Id: I5bfc78abb025adb0ad4fae37e2b444915f477fe7
arch/arm/include/kinetis/kinetis_pmc.h:
* Fix several typos in comments.
* Rewrap some comment lines.
* Fix define KINETIS_PMC_VERSION_UKN: Put -1 in
parenthesis for safety.
* Fix nxstyle complaint regarding long line.
All parts in the STM32H7x3xx family have the same pinmap, etc.,
so extending support to all members of the family required only
minimal changes: Adding them to Kconfig, extending some
preprocessor logic, and minor code changes.
arch/arm/src/stm32h7/Kconfig:
* Add explicit support for all microcontrollers in the
STM32H7x3xx family by adding support for:
- STM32H743AG
- STM32H743AI
- STM32H743BG
- STM32H743BI
- STM32H743IG
- STM32H743II
- STM32H743VG
- STM32H743VI
- STM32H743XG
- STM32H743XI
- STM32H743ZG
- STM32H753AI
- STM32H753BI
- STM32H753VI
- STM32H753XI
- STM32H753ZI
* Fix TODO items for IO_CONFIG (all STM32H7X3XX).
* Because 100-pin parts lack GPIO ports F and G, but have
port H, create the new hidden configs STM32H7_HAVE_GPIOF
and STM32H7_HAVE_GPIOG.
* STM32H7_STM32H7X3XX:
- Select STM32H7_HAVE_GPIOF and STM32H7_HAVE_GPIOG only
when not STM32H7_IO_CONFIG_V (100-pin part).
- STM32H7_STM32H7X3XX: select STM32H7_HAVE_SPI5 for all
IO configs except V (100-pin part), which doesn't expose
SPI5 due to pin count.
* STM32H7_STM32H7X7XX: Always select STM32H7_HAVE_GPIOF and
STM32H7_HAVE_GPIOG because we aren't adding more part
numbers in this family.
* Remove extraneous (duplicate) "bool" and "default n"
lines.
* config STM32H7_FMC: Fix indent (contents were indented
with spaces while rest of file uses tabs).
arch/arm/include/stm32h7/chip.h:
* Extend preprocessor logic to add support for the new
MCU part numbers.
* Expand table of differences between family members.
* Define STM32H7_NGPIO based on IO_CONFIGs decided in Kconfig.
* If IO config is not known, issue compile-time #error
with grep-friendly "CONFIG_STM32H7_IO_CONFIG_x Not Set."
Suggested by davids5.
arch/arm/src/stm32h7/hardware/stm32h7x3xx_gpio.h:
arch/arm/src/stm32h7/stm32h7x3xx_rcc.c:
arch/arm/src/stm32h7/stm32h7x7xx_rcc.c:
* When checking STM32H7_NGPIO > 5 or 6, check also
CONFIG_STM32H7_HAVE_GPIOF or CONFIG_STM32H7_HAVE_GPIOG.
arch/arm/src/stm32h7/stm32_gpio.c:
* stm32_configgpio(): When applicable, make sure we're not
trying to configure one of the missing ports.
* Fix nxstyle complains (wrong end of line comment position
and several long lines). No functional changes.
* g_gpiobase[]: Init base address for ports F and G according to
CONFIG_STM32H7_HAVE_GPIOF and CONFIG_STM32H7_HAVE_GPIOG.
* stm32_configgpio(): Replace complicated check with g_gpiobase[]
null check. Suggested by davids5.
* stm32_gpiowrite() and stm32_gpioread(): Add previously missing
null check of g_gpiobase[].
arch/arm/src/stm32h7/stm32_gpio.h:
* Wrap the defines GPIO_PORTA, GPIO_PORTB, GPIO_PORTC, GPIO_PORTD,
GPIO_PORTE, GPIO_PORTF, GPIO_PORTG, GPIO_PORTH, GPIO_PORTI,
GPIO_PORTJ, and GPIO_PORTK in conditional logic so that the
compiler will prevent use of ports that do not exist on the
target MCU.
* Fix nxstyle complaints.
Documentation/NuttX.html:
* Remove copy-and-pasted anchor for stm32f76xx77xx.
* Correct link to README.txt for Nucleo-H743ZI board,
formerly on BitBucket, now on GitHub.
* Add list item for STMicro STM32H747I-DISCO board.
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
lpc2148_spi1.c:142:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type 'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
142 | .send = spi_send,
| ^~~~~~~~
lpc2148_spi1.c:142:24: note: (near initialization for 'g_spiops.send')
In file included from ieee802154/mac802154_bind.c:49:
ieee802154/mac802154_internal.h: In function 'mac802154_setdevmode':
ieee802154/mac802154_internal.h:788:42: warning: converting a packed 'enum ieee802154_devmode_e' pointer (alignment 1) to a 'const union ieee802154_attr_u' pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
788 | (FAR const union ieee802154_attr_u *)&mode);
| ^~~~~~~~~~~~~~~~~
chip/stm32_hciuart.c: In function 'hciuart_read':
chip/stm32_hciuart.c:2104:30: warning: statement with no effect [-Wunused-value]
2104 | ntotal == (ssize_t)ret;
| ~~~~~~~^~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_auth_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:579:23: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
579 | type = bcmf_getle32(&event->type);
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:580:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
580 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_scan_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:619:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
619 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:620:35: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
620 | escan_result_len = bcmf_getle32(&event->len);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_bdc.c: In function 'bcmf_bdc_process_event_frame':
wireless/ieee80211/bcm43xxx/bcmf_bdc.c:166:27: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
166 | event_id = bcmf_getle32(&event_msg->event.type);
| ^~~~~~~~~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_direct':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:157:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
157 | ret = SDIO_RECVR5(dev, SD_ACMD52, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_extended':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:239:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
239 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:244:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
244 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:257:7: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
257 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:265:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
265 | SDIO_RECVR1(dev, SD_ACMD52ABRT, (uint32_t *)&resp);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:2860:7: warning: unused variable 'ret' [-Wunused-variable]
2860 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:3044:7: warning: unused variable 'ret' [-Wunused-variable]
3044 | int ret;
| ^~~
chip/stm32_i2c.c:722:12: warning: 'stm32_i2c_sem_wait_noncancelable' defined but not used [-Wunused-function]
722 | static int stm32_i2c_sem_wait_noncancelable(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/gs2200m.c: In function 'gs2200m_read':
wireless/gs2200m.c:727:20: warning: passing argument 1 of 'nxsem_wait' from incompatible pointer type [-Wincompatible-pointer-types]
727 | ret = nxsem_wait(dev);
| ^~~
| |
| struct gs2200m_dev_s *
.config:1207:warning: symbol value '' invalid for TESTING_OSTEST_FPUSIZE
platform/audio/cxd56_audio_analog.c:69:13: warning: inline function 'cxd56_audio_clock_is_enabled' declared but never defined
69 | inline bool cxd56_audio_clock_is_enabled(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:68:13: warning: inline function 'cxd56_audio_clock_disable' declared but never defined
68 | inline void cxd56_audio_clock_disable(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:67:13: warning: inline function 'cxd56_audio_clock_enable' declared but never defined
67 | inline void cxd56_audio_clock_enable(uint32_t clk, uint32_t div);
| ^~~~~~~~~~~~~~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:1348:7: warning: unused variable 'ret' [-Wunused-variable]
1348 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:1496:7: warning: unused variable 'ret' [-Wunused-variable]
1496 | int ret;
| ^~~
chip/stm32_i2c.c:729:12: warning: 'stm32_i2c_sem_wait_uninterruptble' defined but not used [-Wunused-function]
729 | static int stm32_i2c_sem_wait_uninterruptble(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/lpwan/sx127x/sx127x.c:147:52: warning: missing terminating ' character
147 | # warning OOK support is not complete, RX+TX doesn't work yet!
| ^
str71_spi.c:435:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type
'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
435 | .send = spi_send,
| ^~~~~~~~
str71_spi.c:435:24: note: (near initialization for 'g_spiops.send')
chip/pic32mx-lowconsole.c:147:24: warning: 'pic32mx_getreg' defined but not used [-Wunused-function]
static inline uint32_t pic32mx_getreg(uintptr_t uart_base,
^
chip/pic32mx-gpio.c:113:20: warning: 'pic32mx_value' defined but not used [-Wunused-function]
static inline bool pic32mx_value(uint16_t pinset)
^
chip/pic32mz-gpio.c:124:20: warning: 'pic32mz_value' defined but not used [-Wunused-function]
static inline bool pic32mz_value(pinset_t pinset)
^
chip/pic32mx-usbdev.c:3065:1: warning: 'pic32mx_epreserved' defined but not used [-Wunused-function]
pic32mx_epreserved(struct pic32mx_usbdev_s *priv, int epno)
^
mmcsd/mmcsd_spi.c: In function 'mmcsd_mediachanged':
mmcsd/mmcsd_spi.c:1938:7: warning: 'return' with a value, in function returning void
return ret;
^
In file included from partition/fs_partition.c:42:0:
partition/partition.h:66:19: warning: 'read_partition_block' defined but not used [-Wunused-function]
static inline int read_partition_block(FAR struct partition_state_s *state,
^
local/local_netpoll.c: In function 'local_pollsetup':
local/local_netpoll.c:305:1: warning: label 'pollerr' defined but not used [-Wunused-label]
pollerr:
^~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: If3ea8f32b878aa218072130f7c3018f0d3c1aca5
As pointed out by Şükrü Bahadır Arslan in PR765, function calls
inside DEBUGASSERT() will not be executed if DEBUGASSERT is
disabled. Following that PR, I searched for other instances of
similar errors and found four. As there are many thousands of
DEBUGASSERT in the code, this is *not* an exhaustive fix.
arch/arm/src/tms570/tms570_boot.c:
* In function arm_boot(), call tms570_memtest_complete()
outside of the DEBUGASSERT(). Otherwise, if DEBUGASSERT is
disabled, we will never rendezvous with completion of the
test. (Two instances of this fix.)
arch/arm/src/tms570/tms570_clockconfig.c:
* In function tms570_clockconfig(), call
tms570_efc_selftest_complete() outside of the DEBUGASSERT()
for the same reason as above.
boards/arm/sam34/sam4s-xplained-pro/src/sam_boot.c:
* In function board_late_initialize(), call
sam_watchdog_initialize() outside of the DEBUGASSERT() for
the same reason as above.
Run all files modified by PR 766 through nxstyle and fix any resulting complaints.
NOTE: Numerous "Mixed case identifier" errors in arch/arm/src/cxd56xx/cxd56_gnss.c were not fixed because this problem is of much larger scope than this file.
This commit resolves issue #620:
Remove CONFIG_CAN_PASS_STRUCTS #620
The configuration option CONFIG_CAN_PASS_STRUCTS was added many years ago to support an old version of the SDCC compiler. That compiler is currently used only with the Z80 and Z180 targets. The limitation of that old compiler was that it could not pass structures or unions as either inputs or outputs. For example:
#ifdef CONFIG_CAN_PASS_STRUCTS
struct mallinfo mallinfo(void);
#else
int mallinfo(FAR struct mallinfo *info);
#endif
And even leads to violation of a few POSIX interfaces like:
#ifdef CONFIG_CAN_PASS_STRUCTS
int sigqueue(int pid, int signo, union sigval value);
#else
int sigqueue(int pid, int signo, FAR void *sival_ptr);
#endif
This breaks the 1st INVIOLABLES rule:
Strict POSIX compliance
-----------------------
o Strict conformance to the portable standard OS interface as defined at
OpenGroup.org.
o A deeply embedded system requires some special support. Special
support must be minimized.
o The portable interface must never be compromised only for the sake of
expediency.
o Expediency or even improved performance are not justifications for
violation of the strict POSIX interface
Also, it appears that the current SDCC compilers have resolve this issue and so, perhaps, this is no longer a problem: z88dk/z88dk#1132
NOTE: This commit cannot pass the PR checks because it depends on matching changes to the apps/ directory.
So call 'make EXTRAFLAGS=-Wno-cpp' could suppress the warnings with pre-processor
directive #warning in GCC.
Change-Id: Iaa618238924c9969bf91db22117b39e6d2fc9bb6
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
- inline functions within mpu.h converted to macros or moved to up_mpu.c
- mpu.h and up_mpu.c are now conditionally included in build via CONFIG_ARM_MPU
Chips affected by these changes
- imxrt
- kinetis
- lpc17xx
- lpc43xx
- lpc54xx
- sam34
- stm32
- stm32f7
- stm32h7
- stm32l4
- tiva
- xmc4
This commit fixes some long single line comments. This effort was primarily intended to verify the change to tools/nxstyle of PR #743 further. This took the files changed with 1501d284c3 and ran them through nxstyle again. The files in the commit previously passed the old nxstyle test with no complaints. The current nxstyle, on the other hand, reported 49 long single line comments. Each of those were verified and the file was updated. The nxstyle change appears completely reliable.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all remaining drivers in the LC823450 architectures.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all remaining drivers in the Atmel SAM architectures.
NOTES:
- arch/arm/src/sama5/sam_can.c: Generates several "Mixed case identifier" complaints because definitions provided by header files that are not part of the change.
- arch/arm/src/sama5/sam_pmecc.c: Has two cases of "Mixed case identifies" result within commented out code. There are references to undefined types that might be provided by Atmel logic (Pmecc and Pmerrloc) if it were ever integrated.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all HCI UART drivers under arch/.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all I2S/SSC drivers under arch/.
In the sam_usb.c file for these two architectures, the USB suspend() operation is implemented, but never called from anywhere. This logic might be valuable in the future for for now it just causes errors due to the unused static function.
This commit just disables the suspend() logic with #if 0 to eliminate the error. The suspend logic is, however, still preserved in case it is needed in the future.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all SDIO card drivers under arch/.
The SDIO interface structure includes fields with names like recvR1 and others. These cause "Mixed case identifier" errors from nxstyle in all places they are uses.
This change performs a mass substition of recvR with recv_r to correct this coding standard violation.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all USB host drivers under arch/.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all SPI drivers under arch/.
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is for all I2C drivers under arch/.
* stm32h7_qspi: Board.h now may define the BOARD_QSPI_CLK macro to select one of
RCC_D1CCIPR_QSPISEL_{HCLK,PLL1,PLL2,PER} clocks to use with QUADSPI peripherial.
Defaults to HCLK for backward compatibility.
New macros in qspi.h: QSPICMD_IDUAL and QSPICMD_IQUAD for selecting the bit
width for instruction code (1,2 or 4 bits) of a qspi_cmdinfo_s, and
QSPIMEM_IDUAL and QSPIMEM_IQUAD for selecting the bit width of a qspi_meminfo_s.
* NX style fixes
Unfortunately nxstyle is still not happy because it doesn't
like the following construct. I'm not sure what to do here.
struct
{
const char *pathname;
long mode;
size_t len;
} open =
{
.pathname = pathname,
.mode = host_flags_to_mode(flags),
.len = strlen(pathname),
};
* stm32h7: New timer output mode STM32_TIM_CH_OUTTOGGLE.
In this mode timer generates a square waveform on given timer channel.
The maximal waveform freq is timer clock divided by 4 (prescaler 1, period 1 results in 2 clocks '0' and 2 clocks '1').
* stm32_tim.h styling fixes.
Also fix the following build warning:
chip/sam_serialinit.c: In function 'sam_earlyserialinit':
chip/sam_serialinit.c:71:4: warning: implicit declaration of function 'uart_earlyserialinit'; did you mean 'sam_earlyserialinit'? [-Wimplicit-function-declaration]
71 | uart_earlyserialinit();
| ^~~~~~~~~~~~~~~~~~~~
| sam_earlyserialinit
Change-Id: I93adc5be739c222482b552b6e143e44c8c047794
Signed-off-by: liuhaitao <liuhaitao@xiaomi.com>
This reverts commit f735584514.
These header changes introduce unacceptable errors:
1. The changes alter the width of the initial block comment. That will cause nxstyle failures on most of the files.
2. The third line of the header is an (optional) short description of content of the the file. This change erroneously removes that line.
Automated header file changes can screw up a lot of files, very quickly.
The DBGMCU_APB1_FZ bit persists over regular software resets until next POR-reset. It can impact device power consumption and things that persist over resets are a bane for FOTA updates so make it disabled by default.
OpenOCD sets this via DAP when connecting to target so enabling this from Kconfig is only useful for users of some other debug tooling.
* SAMA5D27 peripheral support - USB Host working
- updated nsh defconfig with vfat for testing USB Host
- sama5d2_xult: USB Host worked.
- ported sam_bringup.c code from sama5d3-xplained
- USB 2.0 HS now working
- other perpherals may work, but haven't been tested
* update license headers to approve NuttX Apache-2.0
Run all .c files modified by PR424 through nxstyle and correct most of the complaints (many long line complaints ignored for now). Update file headers to use Apache 2.0 license.
Not canceling the I2C timeout watch dog immediately after finishing
all I2C transactions in interrupt context can lead to a race condition
due to nxsem_wait(&priv->wait) in lpc17_40_i2c_start() not resuming
execution fast enough (this can be easily triggered if another task /
thread is using a lot of cpu time).
Falling to cancel the watchdog up to time will cause the priv->wait
semaphore to be incremented twice (first by lpc17_40_i2c_stop() then
by lpc17_40_i2c_timeout()), so all I2C transactions after that will
return immediately and priv->msgs will hold pointers to memory it
doesn't own anymore.
Canceling the priv->timeout watch dog in lpc17_40_i2c_stop() prevents
this as it is executed from the I2C interrupt handler.
arch/arm/src/lpc17xx_40xx/lpc17_40_i2c.c: Fix timeout calculation
For each byte received / transmitted, an acknowledge bit is also
transmitted / received, requiring effectively 9 bits for each byte.
* imxrt: GPIO make tables const
* imxrt: Call out to board to set up FlexRAM
* imxrt: Add Knob for adding the ROM bootloaders 40Kib of RAM to heap
* imxrt: imxrt1060-evk:Add the ability to run from OCRAM
* arch/arm/src/imxrt/imxrt_usbdev.c: Add USB Device support for i.MX RT (USB OTG1)
Based on the LPC43xx USB Device driver.
* imxrt:usbotg Nxstyle fixes
Co-authored-by: thomasactia <61285689+thomasactia@users.noreply.github.com>
There are cases that USE_SERIALDRIVER is defined but USE_EARLYSERIALINIT not defined in some configs. So use ifdef USE_EARLYSERIALINIT to include up_earlyserialinit anyway.
An error was introduced from:
commit f982ee43db
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Date: Tue Feb 18 09:55:04 2020 +0800
drivers/serial: Remove the lowconsole driver
Replace with the syslog console driver which has more capability than lowconsole
* arch/arm/src/tiva/Make.defs: Compile only when enabled by configuration CONFIG_ARM_SEMIHOSTING_HOSTFS
* arch/arm/src/common/up_hostfs.c: Remove the ifdef conditional because it's redundant with the make logic.
Largely copy-and-paste from stm32f4discovery.
Also arch/arm/src/armv7-m/mpu.h: Ensure RBAR alignment
Fix crashes on init task startup I observed on qemu-system-arm -M lm3s6965evb.
And remove syslog_init_e because all initialization is later now and we don't
distinguish the initialition phase anymore after ramlog don't need special
initialize.
Because we can get the same function by CONSOLE_SYSLOG/syslog_console_init.
BTW, it isn't a good choice to use g_ramlogfops as /dev/console since nsh
will read back what it send out which will surprise most people.
it doesn't make sense that iob initialization is in up_initialize
but other memory components initialization is called in nx_start
Change-Id: Id43aeaa995f340c5943f59a0067a483ff3ac34a2
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
To ensure size_t same as toolchain definition in the first place and rename CXX_NEWLONG to ARCH_SIZET_LONG. The change also check whether __SIZE_TYPE__ exist before CONFIG_ARCH_SIZET_LONG so our definition can align with toolchain(gcc/clang) definition automatically.
Currently up_allocate_heap() assumes that g_idle_topstack points
top of the heap memory. However, g_idle_topstack pointed incorrect
address in SMP mode which resulted in heap corruption. This PR
moves g_idle_topstack at the end of .noinit to avoid this issue.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Call xxx_timer_initialize from clock subsystem to make timer ready for use as soon as possiblei and revert the workaround:
commit 0863e771a9
Author: Gregory Nutt <gnutt@nuttx.org>
Date: Fri Apr 26 07:24:57 2019 -0600
Revert "sched/clock/clock_initialize.c: clock_inittime() needs to be done with CONFIG_SCHED_TICKLESS and clock_initialize should skip clock_inittime() for external RTC case since the RTC isn't ready yet."
This reverts commit 2bc709d4b9.
Commit 2bc709d4b9 was intended to handle the case where up_timer_gettime may not start from zero case. However, this change has the side-effect of breaking every implementation of tickless mode: After this change the tickless timer structures are used before they are initialized in clock_inittime(). Initialization happens later when up_initialize is called() when arm_timer_initialize().
Since the tickless mode timer is very special, one solution might be to
1. Rename xxx_timer_initialize to up_timer_initialize
2 Move up_timer_initialize to include/nuttx/arch.h
3. Call it from clock subsystem instead up_initialize
Basically, this change make timer initialization almost same as rtc initialization(up_rtc_initialize).
For now, however, we just need to revert the change.
* S32K add support for Nxp drone boards
* Update arch/arm/src/s32k1xx/hardware/s32k1xx_rtc.h codestyle
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
Co-authored-by: Jari van Ewijk <jari.vanewijk@nxp.com>
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
* Serial Fixed interrupt storm
The target would randomly hang in the serial isr.
The priv->ie and the hardware were inconsistent.
The isr used the priv->ie to gate offloading
the RX data. Bang! Hung.
imxrt_disableuartint(priv, &ie);
ret = imxrt_setup(dev);
/* Restore the interrupt state */
imxrt_restoreuartint(priv, ie);
interrupt-> Of no return
priv->ie = ie;
On a fast cpu with FIFO, this will not work
with out proper protections.
* Serial: Conditionally enable 9 bit mode
* armv7-mi/mpu.hi: Restructure API
Preserve the existing API and enabled better granualriy on
setting.
* Enable MPU for non protected builds to set cache
* mpuinit use symbolic values for addresses
* Allow DTCM on HEAP
* allocateheap Fix Coding style
All STM32L4 MPUs have FLASH_CR_PNB bits (8 bits), and some MPUs have FLASH_CR_BKER bit to change bank if page >= 256.
The code wasn't setting or clearing FLASH_CR_BKER correctly.
Author: Gregory Nutt <gnutt@nuttx.org>
Run .c modified by the PR through tools/nxstyle and correct all reporting coding style problems noted in the file.
Author: Satoshi Togawa <togawa@develcb210.centurysys.co.jp>
STM32L4: Add workaround of data cache corruption on RWW.
Some STM32L4 chips has eratta "Data cache might be corrupted during Flash Read While Write operation". This is also in STM32, and arch/arm/src/stm32/stm32f20xxf40xx_flash.c has workaround.
To enable this workaround, define CONFIG_STM32L4_FLASH_WORKAROUND_DATA_CACHE_CORRUPTION_ON_RWW.
Recent changes removed CONFIG_TIME_ENHANCED and unmasked some warnings. These warnings were caused by nuttx/time.h not being included by files that now referenced clock_daysbeforemonth() and clock_isleapyear().
This commit adds those missing inclusions and eliminates the warnings.
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Fix these build errors which occurred if there was no PHY:
chip/lpc17_40_ethernet.c:1643:31: error: expected expression before ';' token
ret lpc17_40_phyinit();
chip/lpc17_40_ethernet.c:3941:1: error: expected identifier or '(' before '{' token
{
chip/lpc17_40_ethernet.c:448:13: warning: 'lpc17_40_macmode' used but never defined
static void lpc17_40_macmode(uint8_t mode);
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix warning: selects SDIO_DMA or SDIO_BLOCKSETUP which has unmet direct dependencies (MMCSD)
Fix warning: selects NETDEV_TELNET which has unmet direct dependencies (NETDEVICES && NET && NET_TCP)
Fix warning: selects ARCH_PHY_INTERRUPT which has unmet direct dependencies (NETDEVICES && ARCH_HAVE_PHY)
Fix warning: selects USBHOST_HAVE_ASYNCH which has unmet direct dependencies (USBHOST)
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
Fix warning found in build testing: "warning: 'dac_interrupt' defined but not used [-Wunused-function]. The compiler is right, dac_interrupt is not used. It is, apparently, a placeholder for future interrupt support. Now conditioned out with #if 0 to suppress build test warnings.
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
sama5d3-xplained:ethernet-over-phy configuration found in build testing:
arch/arm/src/sama5/sam_irq.c: Fix "Control reaches end of non-void function " warning
arch/arm/src/sama5/sam_udphs.c: Fix "unused variable 'epno'" warning
boards/arm/sama5/sama5d*-*/src/sam_usb.c: Fix "warning 'HAVE_USBHOST' not defined" warnings
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c and .h files and fix it
Author: Juha Niskanen <juha.niskanen@haltian.com>
Fix typos and some incorrect comments
* arch/arm/src/nrf52/hardware/nrf52_twi.h: fix typo
* arch/arm/src/nrf52/nrf52_i2c.c: add interrupts support and some debug messages
* boards/arm/nrf52/nrf52840-dk: add support for hts221 and lsm303agr; boards/arm/nrf52/nrf52840-dk: fix issues noted by nxstyle
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c and .h files and fix it
Author: raiden00pl <raiden00pl@gmail.com>
arch/arm/src/nrf52: use the same naming convention for register defs
arch/arm/src/nrf52/hardware/nrf52_ficr.h: remove invalid defs
arch/arm/src/nrf52/hardware: add TIMER register defs
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle again .c file and fix error message
Author: Daniel P. Carvalho <danieloak@gmail.com>
Add SPWM example to test STM32L4 PWM driver low level operations.
Fix BUGs.
1. No .c file should include a "Public Types" section. Only a header file can define a public type. A .c file can only define a private type. Several files contained private type definitions. The section that they were defined in, however, was incorrectly named "Public Types." Those were easilty changed to "Private Types" which is what they are.
2. No .c file should include a "Public Function Prototypes" section. All global function prototypes should be provided via a header file and never declared with a .c file.
For No. 2, I corrected as many cases as was reasonable for the time that I had available. But there are still a dozen or so .c files that declare "Public Function Prototypes" within a .c file. This is bad programming style. These declarations should all be moved to the proper header files.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle on .c files and fix the issues
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
arch/stm32 ensure all spi dma handler check the result
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle against .c .h files and fix it
Author: Adam Feuer <adam@starcat.io>
Summary
Adds CDC ECM Ethernet over USB High Speed for SAMA5D36-Xplained
(and maybe other boards) (most of the code was there already,
but didn't work out of the box for the SAMA5D36-Xplained)
Only SAMA5D36-Xplained has been tested so far
Impact
None if you don't use the CDC ECM Ethernet driver
On SAMA5D36-Xplained, this adds high-speed Internet connectivity
over USB 2.0 High Speed. via the USB CDC ECM Gadget driver.
It may work on other boards too.
This also fixed full-speed (low-speed) mode for the board too.
Limitations
Hasn't been tested on anything other than SAMA5D36-Xplained board.
TODO
Ideally this would include a composite RNDIS device so it would
also work seamlessly on Windows. That is for a future PR
Ideally this would include software to help configuration via
mDNS/DNS-SD for plug and play compatibility with Linux and macOS.
That is for a future PR.
Detail
Only a few lines of C driver code needed to be changed, since the
capability was there already. The rest is config and documentation.
Changes the SAMA5D3-Xplained board bringup to match the SAMA5D3-EK
board bringup
A helper script to configure Linux routing and iptables NAT is also
provided, along with documentation on how to use it.
Testing
Manual, on a Ubuntu Linux 19.10 system and MacOS 10.14.6 Mojave
MacBook Pro.
How To Verify
Follow the new CDC ECM Ethernet over USB instructions in the board
README.txt file
Commits:
remove non-UTF-8 chars in comment and reformat
removed unneeded comment markers
instructions for using the defconfigs
removed EMAC from config
- to prove this example only needs the CDC ECM Ethernet over USB to work
added CDC-ECM Ethernet over USB info to README
added U-Boot image
added netusb helper script
- this can configure the Linux network interface and routes
so you can ping or access the NuttX system via TCP/IP.
renamed defconfig dirs to be ethernet-over-usb
- was usb-over-ethernet which is not right
added USB DMA to defconfigs
updated readme with autoboot and debugging info
bringing ethernet-over-usb examples into parity
added cdc ecm ethernet over usb with telnetd config
added defconfig
only use phy interrupt if netdevices is ethernet
- because now netdevice could be CDC ECM ethernet over usb
which has no PHY interrupt
add bringup to Makefile
add bringup
app init cleanup
init cdc ecm driver and rndis driver; some cleanup
fixed some typos and odd characters
usb over ethernet working over usb 2.0 hs
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run nxstyle to check .c and .h files and fix reported issues
Author: liuzhao <happypapa@yeah.net>
Add Quectel EC20 4G LTE Module USB CDC/ACM support
nrf52: add support for GPIO interrupts
nrf52: add macros to decode GPIO PIN and GPIO PORT
nrf52: various cosmetic changes
nrf52: fix GPIO P1 memory address
boards/nrf52840-dk: add support for SPI
boards/nrf52840-dk: add support for LSM6DSL sensor
boards/nrf52840-dk: add support for SX127X radio
Author: Alan Carvalho de Assis <acassis@gmail.com>
Check all .c and .h against nxstyle and fix it.
Author: Alin Jerpelea <alin.jerpelea@sony.com>
fs: smartfs: Fix over capacity write
When the remaining capacity of flash is one sector, if a new root
directory is created by file open, then the root directory's chain is
broken and it causes to SmartFS filesystem crash. Once this fatal
problem occurs, it's impossible to recover even if the system reboot.
Fix it by finally update link of root directory.
fs: smartfs: Fix buffer overrun
fs: smartfs: Fix uninitialized variable warnings
fs: smartfs: Memory leak fix
boards: cxd56xx: Update spresense board.h
- Fix PMIC assignment
- Add specific pin configurations for spresense
- Remove unnecessary definitions
arch: cxd56xx: Add ITM syslog init at startup
arch: cxd56xx: Enable DMA settings dynamically
Author: Alan Carvalho de Assis <acassis@gmail.com>
Verify all .c and .h against nxstyle, fixed the Mixed cases
Author: Alin Jerpelea <alin.jerpelea@sony.com>
cxd56xx improvements (#48)
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
* arch: cxd56xx: Add size limitation for I2C SCU xfer
This is a fw restriction, unroll loop because it can be transfer
up to 16 bytes.
* arch: cxd56xx: Fix lack of leave_critical_section
add the missing leave_critical_section
* arch: cxd56xx: Remove unnecessary file
this header is duplicate and we can remove it
* arch: cxd56xx: Cosmetic change
remove space after function
* arch: cxd56xx: update topreg registers
the topreg registers are updated to match the cxd5602 HW
* arch: cxd56xx: Add voltage setting for low battery notification
Add voltage setting for low battery notification
* arch: cxd56xx: Improve perfomance of SD card
Improve a problem that the clock of SD Host Controller is lower than the
expected value in SDR25 transfer mode.
* arch: cxd56xx: Cosmetic changes
cleanup to comply with coding standard
* boards: cxd56xx: Cosmetic changes
updates to comply with coding standard
* boards: cxd56xx: Fix SD card cannot mount issue
SD card cannot mount when connecting and disconnecting three times
or more due to wrong state of parameter 'initialized'.
This change enables to skip swtching initialized state when mount
failed.
Run all .c and .h files in last PR through nxstyle.
Author: 脚蹬破拖鞋 <happypapa@yeah.net>
Add Imxrt usdhc insert or remove detection (#43)
* Add usdhc card insertion and removal detection using interrupt for imxrt.
* Add interrupt handle when usdhc insert or remove.
This commit fixes a compilation error that occurs when enabling the
following configuration items for stm32f7 and stm32h7 architectures:
CONFIG_DEBUG_FEATURES=y
CONFIG_DEBUG_ERROR=y
CONFIG_DEBUG_WARN=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_IRQ=y
CONFIG_DEBUG_IRQ_ERROR=y
CONFIG_DEBUG_IRQ_WARN=y
CONFIG_DEBUG_IRQ_INFO=y
The compiler error for stm32f7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:497:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_FIRST'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_FIRST
chip/stm32_irq.c:497:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
And the compiler error for stm32h7:
make[1]: Entering directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
CC: chip/stm32_irq.c
chip/stm32_irq.c: In function 'stm32_dumpnvic':
chip/stm32_irq.c:164:4: warning: #warning Missing logic [-Wcpp]
# warning Missing logic
^~~~~~~
chip/stm32_irq.c: In function 'up_irqinitialize':
chip/stm32_irq.c:522:29: error: 'STM32_IRQ_NIRQS' undeclared (first use in this function); did you mean 'STM32_IRQ_CRS'?
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
^~~~~~~~~~~~~~~
STM32_IRQ_CRS
chip/stm32_irq.c:522:29: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [Makefile:172: stm32_irq.o] Error 1
make[1]: Leaving directory '/home/pdupreez/dev/wingunder/nuttx/arch/arm/src'
This commit replaces all STM32_IRQ_NIRQS defines with the NR_IRQS
define, which seems to be consistent with the rest of the code in
Nuttx.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Fix long line comments in the header files
Author: Mateusz Szafoni <raiden00pl@users.noreply.github.com>
* arch/arm/src/nrf52: add GPIOTE and SAADC registers definitions
* arch/arm/src/nrf52: update some registers definitions
* arch/arm/src/nrf52: add basic I2C support
* arch/arm/src/nrf52: add function to unconfigure GPIO
* arch/arm/src/nrf52/nrf52_lowputc: add missing FAR
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Run all .c and .h files in last PR through tools/nxstyle and fix all complaints.
Author: macman88 <jjlange91@gmail.com>
LPC17xx serial updates (#29)
* Save CONFIG_ARCH_BOARD_CUSTOM when running 'make savedefconfig'
* Don't compile up_earlyserialinit if USE_EARLYSERIALINIT is not defined
* Added support for RS485 direction control on LPC17xx UART1
* First pass at fractional baud rate divider on LPC17xx/40xx
* Added support for fractional divider to console UART
Author: patacongo <spudarnia@yahoo.com>
arch/arm/src/imxrt/imxrt_enet.c: Fix some warnings found in build testing.
Also fix coding standard problems reported by nxstyle. (#26)
Co-authored-by: Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files in last PR through nxstyle.
Author: macman88 <jjlange91@gmail.com>
SAME5x Ethernet Support (#25)
boards/arm/samd5e5/same54-xplained-pro/: Adds basic support for Microchip SAM E54 Xplained Pro board.
arch/arm/src/samd5e5/: Adds an Ethernet driver for the SAME5x family (based on the SAMA5 GMAC driver).
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Minamiya_Natsuki <yukihiratype2@gmail.com>
Add FMC SDRAM for STM32H7x3 chip (#22)
* Add FMC SDRAM for STM32H7x3 chip
* Add FMC SDRAM for STM32H7x7
* Nuttx Coding Standard requires one declaration per line
* should be __ARCH_ARM_SRC_STM32H7_STM32_FMC_H
* fix bad alignment
* fix typo
* fix typo
* people can't live in furture
* fix comment line length
* fix more comment line length
* fix aligenment
* fix typo
arch/arm/src/sama5/sam_serial.c: uart2port in sam_serial, fix the rest of the uarts in sam_serial
boards/arm/sama5/sama5d2-xult/README.txt: Fix some minor typos
boards/arm/sama5/sama5d2-xult/include/board.h: Update UART pin disambiguation with default UARTn_RXD, _TXD
STM32L4_NUSART was set to 4. The spec at
https://www.st.com/resource/en/datasheet/stm32l433cc.pdf states the
following on page 1:
- 4x USARTs (ISO 7816, LIN, IrDA, modem)
- 1x LPUART (Stop 2 wake-up)
However it on page 49, it states:
The STM32L433xx devices have three embedded universal synchronous
receiver transmitters (USART1, USART2 and USART3).
The latter is correct.
This patch sets STM32L4_NUSART to 3.
Code was flawed in that the Pins are defined with the
pullups in the definition. Since there are no alterntes pins
there is no way to remove them. So not enabling the CONFIG
pull up did nothing as did enabling them.
Code also ignored the use of D0 for ready detection causing
3X+ the chatter.
This is now a compile time feature as there was no reason for
it to be a run time. It wasted both flash and ram.
Squashed commit of the following:
Author: Gregory Nutt <gnutt@nuttx.org>
Ran nxstyle against many of the affected files. But this job was too big for today. Many of the network drivers under arch are highly non-compiant and generate many, many faults from nxstyle. Those will have to be visited again another day.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
This effects all network drivers as well as timing related portions of net/: devif_poll_tcp_timer shouldn't be skipped in the multiple card case. devif_timer will be called multiple time in one period if the multiple card exist, the elapsed time calculated for the first callback is right, but the flowing callback in the same period is wrong(very short) because the global variable g_polltimer is used in the calculation. So let's pass the delay time to devif_timer and remove g_polltimer.
nrf52 updates
board/arm/nrf52/nrf52832-dk: use the on-board virtual COM pins as default UART0 configuration
board/arm/nrf52: initial support for the nrf52840-dk board
board/arm/nrf52: initial support for the nrf52840-dk dongle board
arch/arm/src/nrf52: add support for port 1 GPIO
arch/arm/src/nrf52: initial support for UART1
arch/arm/src/nrf52: add UICR definitions
Approved-by: Gregory Nutt <gnutt@nuttx.org>
STM23L4 LPTIM PWM support with multi-channel
* arch/arm/src/stm32l4/stm32l4_pwm.c:
fixed some bugs
arch/arm/src/stm32l4/stm32l4_pwm.h:
support LPTIM PWM if PWM multi-channel is selected
Channel mode for LPTIM are not available
* arch/arm/src/stm32l4/Kconfig: add new configuration for STM32L4 LPTIM support
* arch/arm/src/stm32l4/stm32l4_pwm.c: fix warning: resetbit may be used uninitialized
Approved-by: Gregory Nutt <gnutt@nuttx.org>
I did suspect that it was just about possible that there's a use for this check (specifically, when you're changing serial the clock immediately after the character is sent) but since we're only testing that the character has left the holding register and not that it's actually been sent to line I don't think it's valid even for this case.
Driver update
* drivers/mtd/Make.defs: Add MTD driver for QuadSPI-based Winbond NOR FLASH
* stm32l4/stm32l4_qspi.c: the "QSPI_DMA_PRIO" has been defined above
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards/arm/stm32h7/stm32h747i-disco: Remove references to nucleo in the stm32h747i-disco board.
arch/arm/include/stm32h7, arch/arm/src/stm32h7, and boards/arm/stm32h7/stm32h747i-disco: Add support for the STM32H747I-DISCO board.
1) Operational issue
TC (Transmission complete) and TDRE (TX Buffer Empty) were transposed in imxrt_serial.c. The end result was that for unoptimised code everything worked fine, but optimised code got itself into a real mess and continually fired interrupts. The patch attached fixes this. This one would have been found much more quickly if this particular board had supported SWO :-/
2) Startup issue
There are a number of chip errata that apply to the 1052 first revision (A-suffix) that don't apply to the second (B-suffix). Those got me for a while and it's important to use an EVK_B_ dev board if you're suffering stability problems with this particular chip. However, even with that resolved with either optimised or unoptimised code when there is no SNVS (Battery Backup) power and the power is switched on the CPU appears to boot but gets stuck with timer interrupts not being generated. The CPU is running and it will execute linear code. I have determined this by putting an 'imxrt_lowputc('A'+irq)' into up_doirq. For the non-running case the output looks like this;
LLLL
this implies 4 0x0b interrupts have been generated, and nothing else. If I hit keys on the keyboard I get 'e' in the flow. 0x0b is the SVC instruction and is the mechanism by which NuttX handles task switching. 'e' is 0x24, which corresponds to the LPUART1 interrupt. Other than these, the system does not respond further but is happily in the idle loop. In this circumstance if you hit SW2 on the EVKB board though the logjam 'unjams' and normal service is established, output now looks like;
LLLLPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPLPP ...etc.
Where 'P' is 0x0f (the SYSTICK interrupt)....this is what _should_ be happening so; SYSTICK starts up after SW2 has been pressed.
From this point on everything works correctly and you can reboot the CPU, put new code into it or do whatever you wish, **provided power is not cycled off**. If power is cycled off then return to the top and go through the process again.
When there is SNVS power to the CPU then power can be switched on and off as you wish, and the CPU will boot correctly. This has been determined by putting 3V onto J6.
I think we are probably doing something naughty with the way we are starting the clocks to the timers. There are certainly some restrictions on imxrt clock manipulation which we have studiously avoided. I am investigating further and have some potential patches but even if I find the root cause it should not be included in 8.2 as the change could be disruptive.
https://github.com/zephyrproject-rtos/zephyr/pull/8535/commits: "The imxrt1050 is configured to use SYSTICK for the kernel timer, but SYSTICK cannot wake up the soc from low-power modes. Disable low-power modes on this soc until we have support for an alternative timer."
"This fixes k_sleep on the EVKB version of the mimxrt1050_evk board. An earlier version of the board (EVK, not EVKB), had A0 silicon which by default did not enter low-power mode on a wfi."
This patch reverts the WFI enable for further investigation post 8.2. With this patch in place together with the previous one my system is fully stable(*), just drinking a bit more power than I'd like.
(1) unifies the iomux definitions - previously some pins had them, and some didn't. This effectively made it impossible to use the pinmuxes without editing the header file in the standard distribution tree.
(2) unifies the pin definitions so that every pin now has a suffix. This makes it *much* easier to see when a pin is in use in your code, because it will always have a definition in your board.h file.
For anyone who is already using this CPU, a couple of small changes are needed to existing code;
In respect of (1) add IOMUX decorators to your pin definitions. You will find defaults in haardware/imxrt_iomux.h. Every pin should have a IOMUX decorator and in general the defaults should be OK. So while previously in your board.h file you might have had;
You will now have;
In respect of (2) you will need to add selectors for any function that previously only had one pinning option. There aren't many of those but LPUART1 is a good example. That just means adding into your board.h something like;
STM32H7:Set the BBSRAM memory range to non-cacheable.
* armv7-m:mpu add user peripheral helper
* stm32h7:BBSRAM Exclude BBSRAM from cacheable when CONFIG_ARMV7M_DCACHE
ST placed the STM32H7 BBSRAM in the SRAM default memory region
which is cacheable. This commit sets the BBSRAM memory range
to non-cacheable.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/tiva/common/tiva_flash.c: Fix several mistakes in
tiva_write() but note that this function needs more work. (1) Fix wrong
use of && when & was intended. (2) Add compile- time warning directive
because according to this function's interface, it is supposed to
support unaligned writes and/or writes of arbitrary numbers of bytes to
FLASH. However, this function does NOT support that at this time. This
needs to be fixed. (3) Fix wrong preprocessor conditional. Was written
to use the 32-word write buffer only for TM4C1294NCPDT. This buffer is
available on all TM4C123 and TM4C129 parts. Now conditioned upon
CONFIG_ARCH_CHIP_TM4C123 or CONFIG_ARCH_CHIP_TM4C129. (4) Add comments
to document the intent of the above preprocessor logic.
stm32l4_otgfs: enable OTGFS for STM32L4+ series
The OTGFS peripheral on stm32l4x6 and stm32l4rxxx reference manual is
exactly the same. This patch also adds missing bits and fixes errors in
stm32l4x5xx and stm32l4x6xx OTGFS register maps.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add DMA support for STM32L4+ series
* Add DMA support for STM32L4+
* stm32l4xrxx_rcc: enable "Range 1 boost" mode if any PLL freq above 80 Mhz
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: spresense: cleanup and new defconfig
* arch: cxd56xx: remove NVIC_SYSH redefinition
The NVIC_SYSH is already defined in nvicpri.h
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: enable SPRESENSE_EXTENSION
Enable high current mode for the Spresense Extension board on all examples
that have SDCARD support
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: ifdef SDCARD_TXS02612
The SD Card TXS02612 port expander is hosted on the Extension board and
should not be enabled if the extension board is not prezent.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: configs: increase MQ_MAXMSGSIZE
This change is needed by the display driver on spresense platform
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: spresense: config: add lcd examples defconfig
This is a configuration for the basic nx examples
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: cxd56xx: spresense: add board_timerhook function
* boards: cxd56xx: spresense: add board_timerhook function
in preparation for SDK we muts have a weak board_timerhook function
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: usbhost: add missing endif
By accident an endif was missing.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: cxd56xx: audio: add build barrier
The audio implementation should not be beuilt if the config
CONFIG_CXD56_AUDIO is not set.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch:arm:cxd56xx: add ge2d.h header
The header is used by imageproc.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: arm: cxd56xx: audio: add power_control and audio_tone_generator
* boards: arm: cxd56xx: audio: add power_control
Add a simeple way to control the audio power for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* boards: arm: cxd56xx: audio: add audio_tone_generator
Add a simple way to control the audio buzzer with defined frequency
for userspace apps
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch/arm/src/stm32f0l0g0: Pinmap TIM1 GPIOs available for STM32G0
arch/arm/src/stm32f0l0g0: Add TIM driver lowerhalf
arch/arm/src/stm32f0l0g0/stm32_tim_lowerhalf.c: Handle 32-bit overflow on some calculations.
arch: armv7-m: Fix a deadlock in up_sigdeliver() in SMP mode.
In previous implementation, up_disable_irq() was called before
recovering local context. However, I noticed a deadlock happens
in the following situation. For example, if up_sigdevliver() is
in progress on CPU0 and CPU1 has called up_cpu_paused to CPU0,
hence g_cpu_irqlock has been locked by CPU1, in this case,
we would see a deadlock in later call of enter_critical_section()
to restore irqcount.
To avoid this situation, we need to call enter_critical_section()
to break the deadlock.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
